Ventev TW-HCEN-FL-TBAR Bruksanvisning

Ventev Inte kategoriserad TW-HCEN-FL-TBAR

Läs nedan 📖 manual på svenska för Ventev TW-HCEN-FL-TBAR (3 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/3
www.ventevinfra.com sales@ventev.com 1-800-851-4965
Flush Mount Hard Cap Wi-Fi Enclosure
Assembly Instructions
Step 1 - Cut a hole into the ceiling as shown in Figure 1. It ers so the lid covers the hole. is important to chamfer the corn
Figure 2
Step 2 - Place the enclosure base into the hole and tighten the 4 screws that clamp the enclosure to the ceiling. Knock outs
are provided to run the RJ45 cable into the enclosure. Shown in Figure 2.
Figure 1
Figure 2
www.ventevinfra.com sales@ventev.com 1-800-851-4965
Flush Mount Hard Cap Wi-Fi Enclosure
Assembly Instructions
Step 3 - Remove the back plate from the enclosure base by removing 4 screws and install the AP to it.
Step 3A - To attach Cisco AP’s, use the key holes provided and place the locking spring pin in the key hole to prevent the AP
from sliding o as shown in Figure 3 and Figure 4. Connect the RJ45 cable to the AP.
Step 3B - To attach Aruba AP’s, insert the ing spring pin in the center hole to preAP feet into the cut outs and place the lock -
vent the AP from sliding o as shown in Figure 5. Connect the RJ45 cable to the AP.
Figure 3 - Cisco
Figure 5 -Aruba
Figure 4 - Cisco
Step 3C - If you are using the Solution that includes a T-Bar, Please follow your AP Manufacturer’s Instructions to attach the
AP T-Bar Mounting Solution to the T-Bar inside the enclosure as shown in Figure 6. Connect the RJ45 cable to the AP.
Figure 6 -T-Bar
www.ventevinfra.com sales@ventev.com 1-800-851-4965
Flush Mount Hard Cap Wi-Fi Enclosure
Assembly Instructions
Step 4 - Screw the back plate back into place to the stand os provided in the base as shown in Figure 7.
Figure 9 Figure 8
Figure 10
Step 6 - To access the AP, pull the cover down and press the spring pin in to remove the cover.
Step 5 - Align the 2 spring pins on the lid assembly into the slots in the enclosure base. Push the lid towards the assembly
keeping the lid level until the cover is tight against the ceiling shown in Figures 8, 9, and 10.
Figure 7

Produktspecifikationer

Varumärke: Ventev
Kategori: Inte kategoriserad
Modell: TW-HCEN-FL-TBAR

Behöver du hjälp?

Om du behöver hjälp med Ventev TW-HCEN-FL-TBAR ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad Ventev Manualer

Ventev

Ventev ID-HCEN-635 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-505 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-535 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-9136 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-515 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-555 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-9120 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-655 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-9130 Bruksanvisning

25 September 2024
Ventev

Ventev ID-HCEN-615 Bruksanvisning

25 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024