VTech DM1111 Bruksanvisning
Läs nedan 📖 manual på svenska för VTech DM1111 (4 sidor) i kategorin Babyvakt. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/4
NOTE
• theWhen POWER/LINK LED light flashes, move
the parent unit closer to the baby unit (observe the
minimum distance of 6.5 feet / 2 meters). You can
also check if the baby monitor is connected to a
live power socket and switched on.
TIP
• Increase the speaker volume of the parent unit if
you cannot hear the sounds transmitted from the
baby unit.
Positioning the baby monitor
CAUTION
• Keep the baby unit out of the reach of baby. your
Never place or mount the baby unit inside the
baby’s crib or playpen.
1. Place the baby unit more than 3 feet
(1 meter) away from your baby.
2. Place the parent unit more than 6.5 feet
(2 meters) away from the baby unit.
CAUTION
• The default volume of your parent unit is , Level 3
and the maximum volume is . If you level 5
experience high-pitched screeching noise from
your baby monitor while positioning:
-Make sure your baby unit and parent unit are
more than 6.5 feet (2 meters) apart, OR
-Turn down the volume of your parent unit.
Operating range
The operating range of the baby monitor is
up to 1,500 feet (450 meters) outdoors or
160 feet (50 meters) indoors. The actual
operating range may vary depending on
the environmental conditions and other
interferences such as walls, doors and other
obstructions.
Overview
Baby unit overview
1 (On/off)
Press and hold to turn on or off the
baby unit.
2Microphone
3POWER light
4Power jack
Parent unit overview
1 Speaker
2 (On/off)
Press and hold to turn on or off the
parent unit.
3 (Volume up)
• Press to increase the speaker
volume.
4POWER / LINK light
5Power jack
6Visual sound indicator
• Indicate the sound level detected by
the baby unit or show the volume
level during speaker volume setting.
7 (Volume down)
• Press to decrease the speaker
volume.
• Press repeatedly until the volume
reaches the minimum to mute the
parent unit.
8 (Low battery light)
9Belt clip
10 Battery compartment cover
Baby unit light
POWER
POWER light
• Lights off when the baby unit is
off.
• Lights on in green when the baby
unit is on.
Parent unit lights
POWER / LINK
POWER / LINK light
• Lights off when the parent
unit is off.
• Lights on in green when the
parent unit is on and linked
to the baby unit.
• Flashes in green when there
is no link between the baby
unit and parent unit, or when
the parent unit is out of
range from the baby unit.
Visual sound indicator
The visual sound indicator has
two functions. One is to show
the sound level detected by
the baby unit. The other one
is to show the volume level
during speaker volume setting.
Sound level detected by the
baby unit
• One to three green lights
indicate a moderate sound
level detected by the baby
unit.
• Additional red lights indicate
a higher sound level
detected by the baby unit
(e.g. baby crying loudly).
Speaker volume level
• One to three green lights
indicate Level 1 to Level
3 of the speaker volume
setting.
• Additional red lights indicate
Level 4 Level 5 to of the
speaker volume setting.
Flashes in red when the
battery is low.
Parent unit alert tones
Low
battery
tone
• Beeps twice every 10 minutes
when the battery is low.
Out of
range
tone
• Beeps three times every 30
seconds when there is no link
between the baby unit and
parent unit, or when the parent
unit is out of range from the baby
unit.
Using the baby monitor
Power on or off the baby unit
• Press and hold until the POWER light
turns on.
• Press and hold until the POWER light
turns off.
Power on or off the parent unit
• Press and hold until the POWER / LINK
light turns on.
• Press and hold until the POWER / LINK
light turns off.
Adjust speaker volume
The speaker volume is preset to Level 3
on the parent unit. You can adjust to your
preferred sound level.
• Press to decrease the volume, and to
increase the volume.
NOTE
• If you continue to press or when the
volume reaches the minimum or maximum
setting, the parent unit will beep twice.
To mute the speaker volume:
• Press repeatedly until the volume
reaches the minimum.
NOTE
S
• When the parent unit is in mute, the visual sound
indicator will still indicate the sound detected from
the baby unit.
• To unmute, press repeatedly until it reaches
your desired volume.
General product care
To keep this product working well and looking good,
follow these guidelines:
• Avoid putting it near heating appliances and
devices that generate electrical noise (for
example, motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby
unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
Storage
When you are not going to use the baby monitor for
some time, remove the AAA alkaline batteries from
the parent unit. Store the parent unit, the baby unit
and the adapters in a cool and dry place.
Operating range
This product operates with the maximum power
allowed by the Federal Communications Commission
(FCC). Even so, the baby unit and the parent unit can
communicate over only a certain distance - which can
vary with the locations of the baby unit, the parent
unit, the weather, and the layout of your home. When
the parent unit is out of range, it will beep three times
every 30 seconds and enter searching mode. To
improve reception, move closer to the baby unit (but
not less than 6.5 feet / 2 meters).
Congratulations
on purchasing your new VTech product. Before
using this product, please read Important
safety instructions.
This manual has all the feature operations
and troubleshooting necessary to install and
operate your new VTech product. Please
review this manual thoroughly to ensure proper
installation and operation of this innovative and
feature rich VTech product.
For support, shopping, and everything new at
VTech, visit our website at
www.vtechphones.com.
What’s in the box
Install batteries for
temporary use
You are recommended to use the power
adapter to power up the parent unit for normal
use. If you want to move around the house
with the parent unit, install two AAA alkaline
batteries for temporary use.
NOTE
• You need to purchase two AAA alkaline batteries
separately.
NOTE
S
• Use 2 x AAA batteries (not included). Alkaline
batteries are recommended. If you use other kind
of batteries, the performance of the baby monitor
varies.
• The parent unit does not support battery
recharging.
• Do not mix old and new batteries. Do not mix
alkaline, standard (Carbon-Zinc) or rechargeable
(Ni-Cad, Ni-Mh, etc) batteries.
• While you insert the batteries, make sure the
polarities are correct.
• When the batteries are installed, the parent unit
turns on.
• Replace the batteries when the light flashes
on the parent unit, or you hear two beeps every
10 minutes.
Install the batteries as shown below.
1. Push to slide open the battery compartment
cover.
2. Insert two AAA alkaline batteries into the
battery compartment, according to the
polarity indications (+) and (-).
3. Slide the battery compartment cover until it
clicks into place.
Replace the battery
To replace the batteries, slide open the battery
compartment cover, and then take out the
batteries. Follow the previous steps to install
the new batteries.
Connect
NOTE
S
• Use only the power adapters supplied with this
product.
• The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if
they are plugged into a ceiling, under-the-table or
cabinet outlet.
• Make sure the parent unit, the baby unit and the
power adapter cords are out of reach of children.
• Both the baby unit and the parent unit are on once
connected to the power supply.
Connect the baby monitor
NOTE
S
• Make sure the light is on after the POWER / LINK
power plug is fully inserted into the power jack of
the parent unit.
• Make sure the baby unit is on. If the parent
unit is not linked to the baby unit, the
POWER / LINK light on the parent unit will flash.
Move the parent unit closer to the baby unit (but
not less than 6.5 feet / 2 meters).
• Make sure the light is on after the power POWER
plug is fully inserted into the power jack of the
baby unit.
Before use
NOTE
• This baby monitor is intended as an aid. It is not a
substitute for proper adult supervision, and should
not be used as such.
Test your baby monitor
You may test the baby monitor before initial
use, and at regular times thereafter.
CAUTION
• For hearing protection, make sure the parent
unit is more than 6.5 feet ( ) away 2 meters
from the baby unit. If you hear any high-
pitched noise, move the parent unit further
until the noise stops. You can also press
on the parent unit to lower or mute the noise.
1. Make sure your baby unit and parent unit
are on.
2. Speak towards the microphone of the baby
unit. You will hear the sound at the parent
unit, and see the visual sound indicators
light up.
User’s manual
DM1111
DM1111-2
Enhanced Range
Digital Audio Monitor
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
St ra ng ul at io n
Haz a
rd
Ke ep th is c ord out o f re ach of childre n.
Th e cord n eed s t o b e a t lea st th ree feet
awa y f
rom the child at all t ime s . D o not
us e with an ex tens ion c or d . Do no t
re move this ta g.
Élo igne z ce cord on des e nfa nt s. Le
co rdon doi t se trouv er à au mo ins t rois
pie ds d ’un enfa nt e t ce, en tou t tem ps.
N’u tilis e z p as d e rall ong e.
N e re t ire z pas
ce tt e éti qu ette .
Manten ga e ste c
abl e fu era de l a al cance
de los n iño s. Es te ca ble deb e e star p or
lo meno s tr es p ies fue ra de la a lcan ce
de l niño en tod o mo me nto . No lo u se
co n una ex tens i ón i nalá mb rica . No quite
es ta etiq ue ta.
Ris q ue
d’é tra ng le me
nt
Rie sg o de
es tran gul ac ió n
Strang
u
latio n
Ha
z ar
d
Kee p th
is c or d out o f rea
ch of chil dren.
The cord
nee ds to b
e at le ast th ree feet
away fr o m th
e child at a ll tim
es. Do not
use w
ith an extens ion co rd
. D o not
remove t his tag.
Éloigne z c e cord on des e
nfa nts. Le
cord
on doit se trou ver à
au m
oins tro is
pieds d’un enfant e t ce, en to
ut te
mps .
N’util ise
z pas d e ra llonge . N
e re
tirez pas
cette é tiquet te.
Mantenga es t e c ab le fu era de l a alca nce
de los niños.
Es te cable debe es tar por
lo m
enos t re
s pie s fu er a de la alcanc e
del n iño en to
do m
omen to . N
o l o us e
co n una extens ión in alámbr ic
a. N
o quite
esta e tiq
ueta.
R
isq
ue
d
’é tranglement
Ries g
o de
estra ngulación
>6.5ft (2m)
1 set for DM1111
2 sets for DM1111-2
Stra
ng ul a t
io n
Ha z a r
d
Kee p th
is cor d
ou t of r each of
ch ildre n
.
The cord nee ds to be at le
ast th ree f eet
aw ay fr om the ch ild
at all times . Do not
use wi th an e
xt ensi o
n cor d. Do no t
re move this tag.
Élo ignez ce c
ordo n d es enfants. Le
cordo n doit se t rouver à au mo ins tr ois
p
ieds d’
un enfant e t ce, e n
to ut tem ps.
N’u tilise z pas de
rallo ng e. N e
retire z p
as
cette étiqu ette
.
M
an teng a
este cable fu era
de la al
ca nce
de lo
s n iños. Es te cab
le debe e
star por
lo menos tres p
ie s fuera
de la alc
an ce
de l ni ño
en todo mo mento . No l o
use
co n u na extens ión i nalám b
rica. No q ui te
esta e tiqueta.
Ris
qu
e
d ’é
tr a ngle ment
Ries go
de
es tr
an gula
ción
Stra ngul atio n
Ha z a r d
Kee p this cor d ou t of r eac
h o f chi ld re n.
The cord nee d s t o b e at leas t three fee t
aw ay f
rom t he
child at
all t imes. Do no
t
use wi th an ext e
nsio n co
rd. Do n
ot
re
move
th is ta g.
Élo i gnez ce cor d on d es
enf ant s.
Le
cordo n d
oit se tro
uv er à a u m oins t
ro is
pie
ds d’un enfant e
t ce, en tou t tem p
s.
N’ut ili
sez pas de ra llonge. Ne r et
irez pas
cette
éti quet
te.
Ma
nten ga est e cable fue ra d e la alca n
ce
de los
n iños. E ste cable d
ebe es
tar por
lo meno s tres pies fuera de la alcan ce
de l niñ o
en todo mo m ento . No lo use
co n u na ex tensió n
ina lámbr ica. No q
uite
esta etiq u eta
.
Risq ue
d’é tr
angle m e nt
Rie s go de
es t
ra ng
ul ac ión
> 3ft (1m)
< 6.5ft (2m)
> 6.5ft (2m)
Frequently asked questions
Below are the questions most frequently asked about
the baby monitor. If you cannot find the answer to your
question, visit our website at www.vtechphones.com,
or contact for customer service.1 (800) 595-9511
Why doesn’t
the POWER
light on the
baby unit turn
on when I
switch on the
units?
Perhaps the baby unit is not
connected to the power supply.
Connect the baby unit to power
supply. The baby unit turns on.
Why doesn’t
the POWER
/ LINK light
on the parent
unit turn on
when I switch
on the units?
Perhaps the battery of the parent
unit is empty and the parent unit is
not connected to power supply.
Connect the parent unit to power
supply; or insert two new AAA
alkaline batteries into the parent
unit. The parent unit turns on and
establishes connection with the
baby unit.
Why does the
baby monitor
not respond
normally?
Try the following (in the order
listed) for common cure:
1. Make sure that both baby
unit and parent unit are on.
Disconnect the power from the
baby unit and the parent unit.
2. Remove the batteries from the
parent unit.
3. Connect the baby unit to the
power supply again. The baby unit
turns on.
4. Connect the parent unit to the
power supply again; or insert
two new AAA alkaline batteries.
The parent unit turns on.
5. Wait for the parent unit to
synchronize with the baby unit.
Allow up to one minute for this
to take place.
6. Press or to adjust the
speaker volume on the parent
unit.
Why does the
baby monitor
produce a
high-pitched
noise?
The units may be too close to
each other. Make sure the parent
unit and the baby unit at least
6.5 feet / 2 meters away from each
other.
Why don’t I
hear a sound/
Why can’t I
hear my baby
cry?
Make sure that both baby unit and
parent unit are on. If you see the
visual sound indicators light up,
but there is no sound, then you
may have muted the volume or
set it to a lower level. Adjust the
volume to a higher level.
If the visual sound indicators do
not light up, and you cannot hear
any sound, it is because the baby
sound is too low for the baby unit
to detect. This is normal. Place
the baby unit at least 6.5 feet / 2
meters away from your baby.
Why does the
parent unit
beep?
The parent unit beeps three times
every 30 seconds when the baby
unit is out of range. Move the
parent unit closer to the baby
unit (but not less than 6.5 feet / 2
meters).
If the parent unit is powered by
batteries, the parent unit beeps
twice every 10 minutes and the
light flashes in red when the
battery is low. Replace with two
new AAA alkaline batteries.
Why does
the parent
unit light
flash?
If the parent unit is powered by
batteries, the parent unit beeps
twice every 10 minutes and the
light flashes in red when the
battery is low. Replace with two
new AAA alkaline batteries, or
remove the batteries, and connect
the parent unit to the power supply.
Why can’t I
establish a
connection?
Why is the
connection
lost every
now and
then? Why
are there
sound
interruptions?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than
6.5 feet / 2 meters).
Other electronic products may
cause interference with your baby
monitor. Try installing your baby
monitor as far away from these
electronic devices as possible.
Important safety instructions
When using your equipment, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock and
injury, including the following:
1. Follow all warnings and instructions marked on
the product.
2. Adult setup is required.
3. This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
4. This product is not intended for use as a medical
monitor.
5. Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in
a wet basement or shower.
6. Use only alkaline batteries (not CAUTION:
included). There may be a risk of explosion if a
wrong type of battery is used for the parent unit.
Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible
special disposal instructions.
7. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can
seriously damage the product.
Baby unit power adapter: Input: 100-120V AC 60
Hz; output: 6V DC 400 mA
Parent unit power adapter: Input: 100-120V AC 60
Hz Output: 6V DC 400mA.
8. The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
9. For pluggable equipment, the socket-outlet
shall be installed near the equipment and shall
be easily accessible.
10. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
11. Unplug the power cords before replacing batteries.
12. Do not cut off the power adapters to replace
them with other plugs, as this causes a
hazardous situation.
13. Do not allow anything to rest on the power cords.
Do not install this product where the cords may
be walked on or crimped.
14. This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home, consult your dealer or local
power company.
15. Do not overload wall outlets or use an extension
cord.
16. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
17. This product should not be placed in any area
where proper ventilation is not provided. Slots
and openings in the back or bottom of this
product are provided for ventilation. To protect
them from overheating, these openings must
not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or
heat register.
18. Never push objects of any kind into this product
through the slots because they may touch
dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.
19. To reduce the risk of electric shock, do not
disassemble this product, but take it to an
authorized service facility. Opening or removing
parts of the product other than specified
access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling
can cause electric shock when the product is
subsequently used.
20. You should test the sound reception every
time you turn on the units or move one of the
components.
21. Periodically examine all components for
damage.
22. Be aware of possible loss of privacy while using
public airwaves. Conversations may be picked
up by other nursery monitors, cordless phones,
scanners, etc.
23. Children should be supervised to ensure that
they do not play with the product.
24. The product is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature
between 32oF and 104oF.
2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to
a heating source.
3. Batteries should not be exposed to excessive
heat such as bright sunshine or fire.
4. Make sure the baby unit and the adapter cord
are always out of reach of the baby, at least 3
feet (1 meter) away from the baby or crib, to
avoid a possible strangulation hazard.
5. Never place the baby unit(s) inside the baby’s crib
or playpen. Never cover the baby unit(s) or parent
unit with anything such as a towel or a blanket.
6. Never cover the baby unit or parent unit(s) with
anything such as a towel or a blanket.
7. Other electronic products may cause
interference with your baby monitor. Try
installing your baby monitor as far away from
these electronic devices as possible: wireless
routers, radios, cellular telephones, intercoms,
room monitors, televisions, personal computers,
kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital cordless
devices):
Wireless Technology Research, LLC (WTR), an
independent research entity, led a multidisciplinary
evaluation of the interference between portable
wireless devices and implanted cardiac
pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches
from the pacemaker.
• Should NOT place wireless devices directly over
the pacemaker, such as in a breast pocket, when
it is turned ON.
WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this
user’s manual, the product is safe to be used based
on scientific evidence available today.
FCC and IC regulations
FCC Part 15
This equipment has been tested and found to
comply with the requirements for a Class B digital
device under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
WARNING: Changes or modifications to this
equipment not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product. This
product has been tested and found to comply with
the FCC criteria. The baby unit shall be installed
and used such that parts of all persons’ body are
maintained at a distance of approximately 8 in (20
cm) or more.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device complies with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference
received, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
This product meets the applicable Innovation,
Science and Economic Development Canada
technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The baby unit should be installed
and operated with a minimum distance of 20 cm
(8 inches) between the baby unit and all persons’
body. For body worn operation, this parent unit
has been tested and meets the FCC RF exposure
guidelines. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines. This
transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment complies also with Industry Canada
RSS-102 with respect to Canada’s Health Code 6 for
Exposure of Humans to RF Fields.
For cETL compliance only
Mesures de sécurité importantes
Lorsque vous utilisez votre appareil, vous devriez
toujours suivre certaines mesures de précaution
de base afin de réduire les risques d’incendie,
d’électrocution et de blessures corporelles, dont
ceux qui suivent :
1. Observez toutes les instructions et mises en
garde inscrites sur l’appareil.
2. L’installation par un adulte est requise.
3. Ce produit a été conçu pour être un dispositif
d’appoint seulement. Il n’est pas le remplacement
d’une supervision responsable et adéquate par un
adulte et ne devrait pas être utilisé comme telle.
4. Ce produit n’est pas conçu pour être utilisé en
tant que moniteur médical.
5. N’utilisez pas cet appareil près de l’eau ni de
toute autre source d’humidité, par exemple, près
d’une baignoire, cuve à lessive, évier de cuisine,
dans un sous-sol humide ni près d’une piscine,
dans un soussol humide ou une douche.
6. MISE EN GARDE : Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de
bloc-piles pour l’unité du parent. N’incinérez pas
les piles. Celles-ci risqueraient d’exploser.
7. N’utilisez que les adaptateurs inclus avec ce
produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre
votre sécurité en péril.
Adaptateur de l’unité du bébé :
Entrée 100-120V AC 60 Hz; Sortie : 6V DC
400 mA
Adaptateur de l’unité du parent :
Entrée 100-120V AC 60 Hz; Sortie : 6V DC
400 mA
8. Lorsqu’ils sont branchés dans une prise de
courant, les adaptateurs secteur ont été conçus
pour être orientés correctement, soit à la
verticale ou au plancher. Les broches n’ont pas
été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici
est branché dans une prise au plafond, sous une
table ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE
PRISE DE COURANT, la prise de courant doit
être installée près du produit, afin d’assurer une
accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant
avant de procéder au nettoyage. N’utilisez pas de
nettoyants en aérosols. Utilisez un chiffon humide
pour le nettoyer.
11. Débranchez les cordons d’alimentation avant de
remplacer le bloc-piles.
12. Ne coupez pas les cordons d’alimentation pour
remplacer les fiches, car ceci peut présenter un
danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur
le cordon d’alimentation. N’installez pas cet
appareil dans un endroit où l’on risque d’écraser
le cordon d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur l’étiquette. Si
vous ne connaissez pas le type d’alimentation
que vous possédez à votre domicile, consultez
votre marchand ou votre compagnie locale
d’électricité.
15. Ne surchargez pas les prises de courant
murales ni les rallonges électriques.
16. Ne placez pas cet appareil sur un chariot,
meuble, trépied, support de montage ni table
chancelants.
17. Les trous et ouvertures du boîtier, situés à
l’arrière de l’appareil ou sous celui-ci, servent à
aérer l’appareil. Pour l’empêcher de surchauffer,
ne bloquez sous aucun prétexte ces ouvertures
et n’empêchez pas l’aération adéquate de
l’appareil en le plaçant sur un lit, divan, tapis ou
toute autre surface similaire. De même, ne le
positionnez pas à proximité ni au-dessus d’une
source de chaleur ou d’un calorifère. De plus, ne
placez pas l’appareil dans un endroit avant de
vous assurer qu’il y ait une bonne circulation d’air.
18. N’enfoncez jamais d’objets à travers les
ouvertures de cet appareil, car ils pourraient
entrer en contact avec des points de tension
dangereux ou causer des courts-circuits qui
peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide
dans ce produit.
19. Afin de réduire les risques d’électrocution, ne
démontez pas cet appareil, mais apportez-le
dans un centre de service autorisé. L’ouverture
du boîtier ou le retrait de toutes pièces que
contient cet appareil, à l’exception de l’accès
autorisé à certaines portes ou ouvertures,
risque de vous exposer à des points de tension
dangereux ou d’autres dangers. Un remontage
incorrect peut par la suite présenter des risques
d’électrocution.
20. Vous devriez tester la réception chaque fois que
vous mettez l’appareil en fonction.
21. Examinez les composantes afin de vérifier si
celles-ci ne sont pas endommagées.
22. Soyez avisé de la perte de la confidentialité
lorsque vous utilisez les ondes publiques. Les
conversations peuvent être entendues par
d’autres moniteurs de bébé, des téléphones
sans fil, des scanneurs, etc.
23. Les enfants devraient être supervisés afin de
vous assurer qu’ils ne jouent pas avec l’appareil.
24. Le produit n’est pas conçu pour être utilisé
par des personnes (incluant des enfants) aux
capacités physiques, sensorielles ou mentales
réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné
suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une
personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une
température entre 0˚ C (32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des
chaleurs extrêmes, ainsi qu’à la lumière directe
du soleil. Ne l’installez pas près d’une source de
chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur
excessive telle que la lumière du soleil ou au feu.
4. Assurez-vous que le moniteur et le cordon
de l’adaptateur sont toujours hors de portée
des enfants, à au moins 1 mètre (3 pieds) de
l’enfant ou du berceau, pour éviter tout risque de
strangulation.
5. Ne jamais placer le moniteur à l’intérieur du
berceau ou du parc de bébé. Ne jamais couvrir
le moniteur ou l’unité (s) portative avec un article
tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent
produire des interférences sur votre moniteur
vidéo et audio. Tentez d’installer votre
moniteur vidéo ou audio à l’écart des appareils
électroniques tels que des routeurs sans fil,
radios, téléphones cellulaires, interphones,
moniteurs, téléphones, ordinateurs personnels,
électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux
dispositifs numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs
et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs
cardiaques
• Vous devriez maintenir les dispositifs sans fil à au
moins six pouces du simulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est
en marche.
L’étude effectuée par l’organisme WRS n’a pas
identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent
dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes
les normes se rapportant aux champs
électromagnétiques (EMF) standard. Si vous le
manipulez correctement en suivant les instructions
de ce guide, son utilisation sera sécuritaire pendant
de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons
aujourd’hui.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase (“Consumer”
or “you”) that the Product and all accessories
provided in the sales package (“Product”) are
free from defects in material and workmanship,
pursuant to the following terms and conditions,
when installed and used normally and in accordance
with the Product operating instructions. This limited
warranty extends only to the Consumer for Products
purchased and used in the United States of America
and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s
authorized service representative will repair
or replace at VTech’s option, without charge,
a Materially Defective Product. If we repair
the Product, we may use new or refurbished
replacement parts. If we choose to replace the
Product, we may replace it with a new or refurbished
Product of the same or similar design. We will
retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s
option, is your exclusive remedy. VTech will return
the repaired or replacement Products to you in
working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If
VTech repairs or replaces a Materially Defective
Product under the terms of this limited warranty,
this limited warranty also applies to the repaired
or replacement Product for a period of either (a)
90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining
on the original one-year warranty; whichever is
longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or other
liquid intrusion; or
2. Product that has been damaged due to repair,
alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced
is caused by signal conditions, network reliability,
or cable or antenna systems; or
4. Product to the extent that the problem is caused
by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product
serial number plates or electronic serial numbers
have been removed, altered or rendered illegible;
or
6. Product purchased, used, serviced, or shipped for
repair from outside the United States of America
or Canada, or used for commercial or institutional
purposes (including but not limited to Products
used for rental purposes); or
7. Product returned without a valid proof of purchase
(see item 2 in the next column); or
8. Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit
our website at www.vtechphones.com or
call 1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls
and features may save you a service call.
Except as provided by applicable law, you assume
the risk of loss or damage during transit and
transportation and are responsible for delivery or
handling charges incurred in the transport of the
Product(s) to the service location. VTech will return
repaired or replaced Product under this limited
warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for
damage or loss of the Product in transit. If the Product
failure is not covered by this limited warranty, or proof
of purchase does not meet the terms of this limited
warranty, VTech will notify you and will request that
you authorize the cost of repair prior to any further
repair activity. You must pay for the cost of repair and
return shipping costs for the repair of Products that
are not covered by this limited warranty.
What must you return with the Product to get
warranty service?
1. Return the entire original package and contents
including the Product to the VTech service
location along with a description of the malfunction
or difficulty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model)
and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to this
Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There
are no other express warranties. No one is authorized
to make modifications to this limited warranty and you
should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other
rights, which vary from state to state or province to
province.
Limitations: Implied warranties, including those of
fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary
use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on
how long an implied warranty lasts, so the above
limitation may not apply to you. In no event shall
VTech be liable for any indirect, special, incidental,
consequential, or similar damages (including, but
not limited to lost profits or revenue, inability to use
the Product or other associated equipment, the cost
of substitute equipment, and claims by third parties)
resulting from the use of this Product. Some states/
provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof
of purchase.
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 1921.536 - 1928.448 MHz
Parent unit: 1921.536 - 1928.448 MHz
Channels 5
Nominal
effective
range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirements
Baby unit adapter:
Input: 100-120V AC 60Hz
Output: 6V DC @ 400mA
Parent unit adapter:
Input: 100-120V AC 60Hz
Output: 6V DC @ 400mA
Parent unit battery:
2 X AAA alkaline batteries
Specifications are subject to change without notice.
© 2018 VTech Communications, Inc.
All rights reserved. 02/18. DM1111-X_CIB_V2.0
Document order number: 91-010894-020-100
Produktspecifikationer
| Varumärke: | VTech |
| Kategori: | Babyvakt |
| Modell: | DM1111 |
Behöver du hjälp?
Om du behöver hjälp med VTech DM1111 ställ en fråga nedan och andra användare kommer att svara dig
Babyvakt VTech Manualer
2 Oktober 2024
19 September 2024
15 September 2024
22 Augusti 2024
20 Augusti 2024
7 Augusti 2024
6 Augusti 2024
6 Augusti 2024
4 Augusti 2024
26 Juli 2024
Babyvakt Manualer
- Babyvakt IKEA
- Babyvakt Brondi
- Babyvakt Philips
- Babyvakt Grundig
- Babyvakt Motorola
- Babyvakt Topcom
- Babyvakt Tefal
- Babyvakt Alcatel
- Babyvakt Alecto
- Babyvakt Angelcare
- Babyvakt Ansmann
- Babyvakt Amplicomms
- Babyvakt Silvercrest
- Babyvakt SereneLife
- Babyvakt Beurer
- Babyvakt Hyundai
- Babyvakt Chicco
- Babyvakt Jane
- Babyvakt Overmax
- Babyvakt Concept
- Babyvakt Medisana
- Babyvakt Ezviz
- Babyvakt Elro
- Babyvakt EMOS
- Babyvakt Denver
- Babyvakt Hama
- Babyvakt Cresta
- Babyvakt Babymoov
- Babyvakt Eufy
- Babyvakt Sanitas
- Babyvakt Audioline
- Babyvakt Uniden
- Babyvakt BT
- Babyvakt Goclever
- Babyvakt Graco
- Babyvakt BabyOno
- Babyvakt Oricom
- Babyvakt Safety 1st
- Babyvakt Switel
- Babyvakt Duux
- Babyvakt Nova
- Babyvakt Luvion
- Babyvakt Konig
- Babyvakt Reer
- Babyvakt Tesla
- Babyvakt Foscam
- Babyvakt D-Link
- Babyvakt Lionelo
- Babyvakt Lorex
- Babyvakt Basetech
- Babyvakt HQ
- Babyvakt Chipolino
- Babyvakt Beaba
- Babyvakt Bebetel
- Babyvakt Truelife
- Babyvakt NUK
- Babyvakt Tomy
- Babyvakt Babysense
- Babyvakt Modern-Electronics
- Babyvakt Duronic
- Babyvakt Hartig Helling
- Babyvakt Levana
- Babyvakt IBaby
- Babyvakt Kogan
- Babyvakt Mobi
- Babyvakt Neonate
- Babyvakt Pabobo
- Babyvakt Neno
- Babyvakt Philips-Avent
- Babyvakt Heimvision
- Babyvakt BabySafe
- Babyvakt Chillax Baby
- Babyvakt Hubble Connected
- Babyvakt Peekyboo
Nyaste Babyvakt Manualer
27 Oktober 2024
23 Oktober 2024
22 Oktober 2024
21 Oktober 2024
21 Oktober 2024
21 Oktober 2024
20 Oktober 2024
20 Oktober 2024
19 Oktober 2024
18 Oktober 2024