VTech VM990 Bruksanvisning

VTech Babyvakt VM990

Läs nedan 📖 manual på svenska för VTech VM990 (2 sidor) i kategorin Babyvakt. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

User’s manual

VM990

Accessory Wi-Fi

Pan & Tilt HD Camera

for use with VTech model

VM981/VM991

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safety instructions.

This manual has instructions on how to set up

your new camera unit. For complete instructions

on using the camera unit, see the installation

guide, quick start guide, and the online app

manual of the HD video monitor.

For support, shopping, and everything new at

VTech, visit our website at

www.vtechphones.com.

3-month warranty!

Visit www.vtechphones.com.

Registration

enhanced warranty support.

Product news

Learn about the latest VTech

products.

1Light sensor

2Infrared LEDs

• Allow you to see clearly in a dark

surrounding.

3Camera lens

4Microphone

5Antenna

• Connect to router with Wi-Fi.

6Speaker

7Power jack

8Ethernet port

• Connect to router with an RJ45

network cable (optional).

93.5mm line jack

• Connect to audio output device

(optional).

10 micro SD card slot

11 LED indicators

• Flash orange and blue alternately

when the camera unit is in pairing

mode.

• Orange is steady on when the camera

unit is connecting to the Internet.

• Orange and blue are steady on when

the camera unit is idle.

• Flash orange and blue slowly during

video streaming.

• Flash orange and blue quickly and

alternately when the camera unit is

updating its firmware.

12 Volume –

• Press to decrease the camera unit

speaker volume.

Volume +

• Press to increase the camera unit

speaker volume.

13 Pair/reset button

• Press and hold for three seconds to

enter pairing mode.

What’s in the box

mic

User’s manual

x 2

Overview

mic

4. Place the camera unit on the wall mount

bracket, and then slide it forward until it locks

into place.

-OR-

5. Connect the power adapter to the camera unit

and a power supply not controlled by a wall

switch.

Mount the camera unit (optional)

1. Place the wall mount bracket on a wall or on

the ceiling, and then use a pencil to mark two

holes in parallel.

2. Remove the wall mount bracket and then drill

two holes in the wall or on the ceiling (7/32”

drill bit).

• If you drill the holes into an object other than a

stud, insert the wall anchors into the holes and

tap gently on the ends with a hammer until the

wall anchors are flush with the wall.

3. Align the holes on the wall mount bracket

with the screws on the wall or on the ceiling.

Tighten the screws in the holes.

volume

micro SD

Insert micro SD card

Your camera unit can capture videos of the

monitoring area when detects motions. You can

choose to save the videos to a micro SD card.

NOTES

• Your camera supports Class 4 or higher micro SD

card, with storage capacity up to 32GB.

CAUTION

• Before inserting or ejecting the micro SD card of

your camera, you must first power off the camera. To

power off, unplug the camera from the power supply.

Connect to audio output device

(optional)

The camera unit has a built-in speaker. You can

also connect an external self-powered speaker to

your camera unit for extra sound quality.

2. Place the camera unit at a desired place.

NOTES

• To turn off the camera unit, unplug the camera unit

from the power supply.

Cable connection (optional)

After you have paired the camera unit with your

parent unit via Wi-Fi, you can connect the camera

unit to the Internet using the network cable to

optimize your Internet connection. Refer to the

online app manual for the instructions on how to

pair your camera unit with your parent unit.

Connect

NOTES

• Use only the power adapter supplied with this

product.

• Make sure the electrical outlet is not controlled by

wall switch.

• The power adapter is intended to be correctly oriented

in a vertical or floor mount position. The prongs are

not designed to hold the plug in place if it is plugged

into a ceiling, under-the-table or cabinet outlet.

• Make sure the camera unit and the power adapter

cord are out of reach of children.

Connect the camera unit

You can choose to set up the camera unit

for desktop usage, wall mounting or ceiling

mounting.

Wi-Fi connection

NOTES

• Before you connect the camera unit, make sure you

have Internet access and a Wi-Fi router

(IEEE 802.11 b/g/n). Charges apply and service

plan may vary for Internet access. Router is not

included.

• Do not plug in the network cable.

• To maintain compliance with the FCC’s RF exposure

guidelines, place the camera unit at least 20cm from

nearby persons.

1. Connect the power adapter to the camera unit

and a power supply.

volume

micro SD

Before use

How the system works

The Wi-Fi router (not included) provides Internet

connectivity to your HD video monitor system.

It serves as a communicating channel between

your camera unit and parent unit, allowing you to

monitor and/or control your camera unit wherever

you are.

Requirements

Make sure your system includes the following

components, and they meet the minimum

requirement.

Network Wi-Fi

Wi-Fi router 2.4GHz IEEE 802.11 b/g/n

Internet connection At least 1.0 Mbps upload

bandwidth per camera

micro SD card Support Class 4 or higher,

with storage capacity up to

32GB

Test the location for the camera unit

Before you install your camera unit, you need to

test which of your selected monitoring areas within

the house have good Wi-Fi signal strength. After

you have connected your parent unit to a Wi-Fi

network, you can use your parent unit’s Wi-Fi

signal strength indicator to assist in checking.

Once you have identified the suitable location, you

can install your camera unit. Adjust the distance

between your camera unit and the Wi-Fi router if

needed.

TIP

• Depending on surroundings and obstructing factors,

such as the effect distance and internal walls have

on signal strength, you may experience reduced

Wi-Fi signal. To improve the Wi-Fi signal strength,

adjust the distance or direction of your parent unit.

Check with your parent unit again.

Pair new camera unit

Each newly purchased camera unit (VM990)

must be paired to the parent unit of the HD video

monitor system (VM981 or VM991).

Refer to the online app manual in your parent unit

on how to pair your camera unit to your system.

AUDIO IN

volume

micro SD

volume

micro SD

volume

micro SD

micro S

Click!

Protect your privacy and online

security

VTech cares about your privacy and peace of

mind. That’s why we’ve put together a list of

industry-recommended best practices to help

keep your wireless connection private and your

devices protected when online. We recommend

you carefully review and consider complying with

the following tips.

Ensure your wireless connection is secure.

• Before installing a device, ensure your router’s

wireless signal is encrypted by selecting the

“WPA2-PSK with AES” setting in your router’s

wireless security menu.

Change default settings.

• Change your wireless router’s default wireless

network name (SSID) to something unique.

• Change default passwords to unique, strong

passwords. A strong password:

- Is at least 10 characters long.

- Is complex.

- Does not contain dictionary words or

personal information.

- Contains a mix of uppercase letters,

lowercase letters, special characters and

numbers.

Keep your devices up to date.

• Download security patches from

manufacturers as soon as they become

available. This will ensure you always have

the latest security updates.

• If the feature is available, enable automatic

updates for future releases.

Disable Universal Plug and Play (UPnP) on your

router.

• UPnP enabled on a router can limit the

effectiveness of your firewall by allowing other

network devices to open inbound ports without

any intervention or approval from you. A virus

or other malware program could use this

function to compromise security for the entire

network.

For more information on wireless connections

and protecting your data, please review the

following resources from industry experts:

1. Federal Communications Commission:

Wireless Connections and Bluetooth Security

Tips–

www.fcc.gov/consumers/guides/how-protect-

yourself-online.

2. U.S. Department of Homeland Security:

Before You Connect a New Computer to the

Internet–

www.us-cert.gov/ncas/tips/ST15-003.

3. Federal Trade Commission: Using IP

CamerasSafely–

https://www.consumer.ftc.gov/articles/0382-

using-ip-cameras-safely.

4. Wi-FiAlliance:DiscoverWi-FiSecurity–

http://www.wi-.org/discover-wi-/security.

WIFI MAC:0012A4A3CE4

LAN MAC:00122A4A3CE5

S/N:VM500006007

Model:

VM990

Specifications are subject to change without notice.

Document order number: 91-010169-030-100

Technical specifications

Frequency Camera unit: 2412 - 2462 MHz

Channels 11

Nominal

effective

range

Maximum power allowed by FCC

and IC. Actual operating range may

vary according to environmental

conditions at the time of use.

Power

requirement

Camera unit power adapter:

Input: 100-240V AC 50/60Hz

Output: 5V DC 1500mA

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to

the holder of a valid proof of purchase (“Consumer”

or “you”) that the Product and all accessories

provided in the sales package (“Product”) are

free from defects in material and workmanship,

pursuant to the following terms and conditions,

when installed and used normally and in accordance

with the Product operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America

and Canada.

What will VTech do if the Product is not free from

defects in materials and workmanship during

the limited warranty period (“Materially Defective

Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace the

Product, we may replace it with a new or refurbished

Product of the same or similar design. We will retain

defective parts, modules, or equipment. Repair or

replacement of the Product, at VTech’s option, is

your exclusive remedy. VTech will return the repaired

or replacement Products to you in working condition.

You should expect the repair or replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends

for ONE (1) YEAR from the date of purchase. If

VTech repairs or replaces a Materially Defective

Product under the terms of this limited warranty,

this limited warranty also applies to the repaired or

replacement Product for a period of either (a) 90 days

from the date the repaired or replacement Product

is shipped to you or (b) the time remaining on the

original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse,

accident, shipping or other physical damage,

improper installation, abnormal operation or

handling, neglect, inundation, fire, water or other

liquid intrusion; or

2. Product that has been damaged due to repair,

alteration or modification by anyone other than

an authorized service representative of VTech; or

3. Product to the extent that the problem

experienced is caused by signal conditions,

network reliability, or cable or antenna systems;

4. Product to the extent that the problem is caused

by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product

serial number plates or electronic serial numbers

have been removed, altered or rendered illegible;

6. Product purchased, used, serviced, or shipped

for repair from outside the United States of

America or Canada, or used for commercial or

institutional purposes (including but not limited to

Products used for rental purposes); or

7. Product returned without a valid proof of

purchase (see item 2 on the next page); or

8. Charges for installation or set up, adjustment of

customer controls, and installation or repair of

systems outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit

our website at www.vtechphones.com or call

1-844-848-8324 (1-844-84-VTECH). In Canada, go to

www.vtechcanada.com or call 1-888-211-2005.

NOTE: Before calling for service, please review the

user’s manual - a check of the Product’s controls

and features may save you a service call.

Except as provided by applicable law, you assume

the risk of loss or damage during transit and

transportation and are responsible for delivery

or handling charges incurred in the transport of

the Product(s) to the service location. VTech

will return repaired or replaced Product under

this limited warranty. Transportation, delivery or

handling charges are prepaid. VTech assumes no

risk for damage or loss of the Product in transit. If

the Product failure is not covered by this limited

warranty, or proof of purchase does not meet the

terms of this limited warranty, VTech will notify you

and will request that you authorize the cost of repair

prior to any further repair activity. You must pay for

the cost of repair and return shipping costs for the

repair of Products that are not covered by this limited

warranty.

What must you return with the Product to get

warranty service?

1. Return the entire original package and

contents including the Product to the VTech

service location along with a description of the

malfunction or difficulty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product

model) and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech. It supersedes

all other written or oral communications related to

this Product. VTech provides no other warranties for

this Product. The warranty exclusively describes all

of VTech’s responsibilities regarding the Product.

There are no other express warranties. No one

is authorized to make modifications to this limited

warranty and you should not rely on any such

modification.

State/Provincial Law Rights: This warranty gives you

specific legal rights, and you may also have other rights,

which vary from state to state or province to province.

Limitations: Implied warranties, including those of

fitness for a particular purpose and merchantability (an

unwritten warranty that the Product is fit for ordinary

use) are limited to one year from the date of purchase.

Some states/provinces do not allow limitations on how

long an implied warranty lasts, so the above limitation

may not apply to you. In no event shall VTech be liable

for any indirect, special, incidental, consequential,

or similar damages (including, but not limited to lost

profits or revenue, inability to use the Product or

other associated equipment, the cost of substitute

equipment, and claims by third parties) resulting from

the use of this Product. Some states/provinces do

not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or

exclusion may not apply to you.

Please retain your original sales receipt as proof

of purchase.

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to

comply with the requirements for a Class B digital

device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Changes or modifications to this equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established

criteria for the amount of radio frequency energy

that can be safely absorbed by a user or bystander

according to the intended usage of the product. This

product has been tested and found to comply with

the FCC criteria. The camera unit shall be installed

and used such that parts of all persons’ body are

maintained at a distance of approximately

8 in (20 cm) or more.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device complies with Industry Canada licence-

exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation.

The term ‘’IC:‘’ before the certification/registration

number only signifies that the Industry Canada

technical specifications were met.

This product meets the applicable Industry Canada

technical specifications.

RF radiation exposure statement

The camera unit complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The camera unit should be installed

and operated with a minimum distance of 8 in

(20 cm) between the main unit and all persons’

body. Use of other accessories may not ensure

compliance with FCC RF exposure guidelines. This

transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

This equipment complies also with Industry Canada

RSS-210 with respect to Canada’s Health Code 6 for

Exposure of Humans to RF Fields.

connaissances, à moins qu’on leur ait donné

suffisamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une

personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température

entre0˚C(32˚F)et40˚C(104˚F).

2. N’exposez pas cet appareil à des froids ou des

chaleurs extrêmes, ainsi qu’à la lumière directe

du soleil. Ne l’installez pas près d’une source de

chauffage.

3. D’autres produits électroniques peuvent causer

des interférences auprès de votre caméra

IP. Essayez d’installer votre caméra IP le plus

loin possible de ces dispositifs électroniques :

routeurs sans fil, radios, téléphones cellulaires,

interphones, moniteurs de pièces, téléviseurs,

ordinateurs personnels, appareils électriques de

cuisine et téléphones sans fil.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux

dispositifs numériques sans fil):

L’organisme ‘Wireless Technology Research, LLC

(WTR)’, une firme de recherche indépendante,

a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil portatifs

et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des

aliments et drogues (FDA) des États-Unis, la firme

WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à

au moins six pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil

directement sur le stimulateur cardiaque, tel que

dans une poche de chemise, lorsque celui-ci est

en marche.

L’étude effectuée par l’organisme WRS n’a

pas identifié de risque pour les détenteurs de

simulateurs cardiaques causés par les gens qui

utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes

les normes se rapportant aux champs

électromagnétiques (EMF) standard. Si vous le

manipulez correctement en suivant les instructions

de ce guide, son utilisation sera sécuritaire pendant

de nombreuses années, selon les meilleures

évidences scientifiques dont nous disposons

aujourd’hui.

For cETL compliance only

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez

toujours suivre certaines mesures de précaution

de base afin de réduire les risques d’incendie,

d’électrocution et de blessures corporelles, dont

ceux qui suivent:

1. Observez toutes les instructions et mises en

garde inscrites sur l’appareil.

2. L’installation par un adulte est requise.

3. Ce moniteur résidentiel est conçu à titre d’aide

seulement. Il ne remplace pas les systèmes de

surveillance résidentiels et ne doit pas être utilisé

comme tel.

4. Ce produit n’est pas conçu pour être utilisé en

tant que moniteur médical.

5. N’utilisez pas cet appareil près de l’eau ni de toute

autre source d’humidité, par exemple, près d’une

baignoire, cuve à lessive, évier de cuisine, dans

un sous-sol humide ni près d’une piscine, dans un

soussol humide ou une douche.

6. N’utilisez que les adaptateurs inclus avec ce

produit. L’utilisation d’un adaptateur dont la

polarité ou la tension serait inadéquate risque

d’endommager sérieusement le produit et mettre

votre sécurité en péril.

Adaptateur secteur de la caméra :

Entrée 100-240V CA 50/60 Hz;

Sortie : 5 V CC 1500 mA.

7. Lorsqu’ils sont branchés dans une prise de

courant, les adaptateurs secteur ont été conçus

pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas

été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici

est branché dans une prise au plafond, sous une

table ou dans un meuble.

8. Pour les appareils raccordés, la prise de courant

(de l’adaptateur secteur) doit être installée

près de l’équipement et doit être facilement

accessible.

9. Débranchez ce produit de la prise de courant

avant de procéder au nettoyage. N’utilisez pas

de nettoyants en aérosols. Utilisez un chiffon

humide pour le nettoyer.

10. Ne coupez pas les cordons d’alimentation pour

remplacer les fiches, car ceci peut présenter un

danger potentiel.

11. Ne laissez aucun objet reposer ni appuyer sur le

cordon d’alimentation. N’installez pas cet appareil

dans un endroit où l’on risque d’écraser le cordon

d’alimentation ou de le piétiner.

12. Ne faites fonctionner cet appareil qu’avec le type

d’alimentation indiqué sur l’étiquette. Si vous

ne connaissez pas le type d’alimentation que

vous possédez à votre domicile, consultez votre

marchand ou votre compagnie locale d’électricité.

13. Ne surchargez pas les prises de courant murales

ni les rallonges électriques.

14. Ne placez pas cet appareil sur un chariot, meuble,

trépied, support de montage ni table chancelants.

15. Les trous et ouvertures du boîtier, situés à

l’arrière de l’appareil ou sous celui-ci, servent à

aérer l’appareil. Pour l’empêcher de surchauffer,

ne bloquez sous aucun prétexte ces ouvertures

et n’empêchez pas l’aération adéquate de

l’appareil en le plaçant sur un lit, divan, tapis ou

toute autre surface similaire. De même, ne le

positionnez pas à proximité ni au-dessus d’une

source de chaleur ou d’un calorifère. De plus,

ne placez pas l’appareil dans un endroit avant

de vous assurer qu’il y ait une bonne circulation

d’air.

16. N’enfoncez jamais d’objets à travers les

ouvertures de cet appareil, car ils pourraient

entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui

peuvent dégénérer en incendies ou en risques

d’électrocution. Ne renversez jamais de liquide

dans ce produit.

17. Afin de réduire les risques d’électrocution, ne

démontez pas cet appareil, mais apportez-le dans

un centre de service autorisé. L’ouverture du

boîtier ou le retrait de toutes pièces que contient

cet appareil, à l’exception de l’accès autorisé à

certaines portes ou ouvertures, risque de vous

exposer à des points de tension dangereux ou

d’autres dangers. Un remontage incorrect peut par

la suite présenter des risques d’électrocution.

18. Vous devriez tester la réception chaque fois que

vous mettez l’appareil en fonction.

19. Examinez les composantes afin de vérifier si

celles-ci ne sont pas endommagées.

20. Soyez avisé de la perte de la confidentialité

lorsque vous utilisez les ondes publiques. Les

conversations peuvent être entendues par

d’autres moniteurs de bébé, des téléphones sans

fil, des scanneurs, etc.

21. Les enfants devraient être supervisés afin de

vous assurer qu’ils ne jouent pas avec l’appareil.

22. Les petites pièces de ce moniteur peuvent être

avalées par les bébés ou les petits enfants.

Veuillez tenir ces pièces hors de portée des

enfants.

23. Le produit n’est pas conçu pour être utilisé

par des personnes (incluant des enfants) aux

capacités physiques, sensorielles ou mentales

réduites ou qui manquent d’expérience et de

Locate the online app manual

To access the online app manual from

the parent unit:

1. Tap to display the side menu.

2. Tap Help.

3. Tap App manual to read the online app

manual.

General product care

To keep this product working well and looking

good, follow these guidelines:

• Avoid putting it near heating appliances and

devices that generate electrical noise (for

example, motors or fluorescent lamps).

Storage

When you are not going to use the camera for

some time, store the camera unit and the adapter

in a cool and dry place.

Important safety instructions

When using your equipment, basic safety

precautions should always be followed to reduce

the risk of fire, electric shock and injury, including

the following:

1. Follow all warnings and instructions marked

on the product.

2. Adult setup is required.

3. This home monitor is intended as an aid. It is

not a substitute for home security supervision

and should not be used as such.

4. This product is not intended for use as a

medical monitor.

5. Do not use this product near water. For

example, do not use it next to a bath tub,

wash bowl, kitchen sink, laundry tub or

swimming pool, or in a wet basement or

shower.

6. Use only the adapters included with this

product. Incorrect adapter polarity or voltage

can seriously damage the product.

Power adapter: Input 100-240V AC 50/60Hz;

Output: 5V DC 1500mA.

7. The power adapter is intended to be correctly

oriented in a vertical or floor mount position.

The prongs are not designed to hold the plug

in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

8. For pluggable equipment, the socket-outlet

(power adapter) shall be installed near the

equipment and shall be easily accessible.

9. Unplug this product from the wall outlet

before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

10. Do not cut off the power adapters to replace

them with other plugs, as this causes a

hazardous situation.

11. Do not allow anything to rest on the power

cords. Do not install this product where the

cords may be walked on or crimped.

12. This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home, consult your dealer or

local power company.

13. Do not overload wall outlets or use an

extension cord.

14. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

15. This product should not be placed in any area

where proper ventilation is not provided. Slots

and openings in the back or bottom of this

product are provided for ventilation. To protect

them from overheating, these openings must

not be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or over a

radiator or heat register.

16. Never push objects of any kind into this

product through the slots because they may

touch dangerous voltage points or create a

short circuit. Never spill liquid of any kind on

the product.

17. To reduce the risk of electric shock, do

not disassemble this product, but take it to

an authorized service facility. Opening or

removing parts of the product other than

specified access doors may expose you to

dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when

the product is subsequently used.

18. You should test the sound reception every

time you turn on the units or move one of the

components.

19. Periodically examine all components

for damage.

20. Be aware of possible loss of privacy while

using public airwaves. Conversations may be

picked up by other nursery monitors, cordless

phones, scanners, etc.

21. Children should be supervised to ensure that

they do not play with the product.

22. The small parts of this monitor can be

swallowed by babies or small children. Keep

these parts out of reach of children.

23. The product is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

• Use and store the product at a temperature

between 32oF and 104oF.

• Do not expose the product to extreme cold,

heat or direct sunlight. Do not put the product

close to a heating source.

• Other electronic products may cause

interference with your camera unit. Try

installing your camera unit as far away from

these electronic devices as possible: wireless

routers, radios, cellular telephones, intercoms,

room monitors, televisions, personal

computers, kitchen appliances and cordless

telephones.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital

cordless devices):

Wireless Technology Research, LLC (WTR),

an independent research entity, led a

multidisciplinary evaluation of the interference

between portable wireless devices and implanted

cardiac pacemakers. Supported by the U.S. Food

and Drug Administration, WTR recommends to

physicians that:

Pacemaker patients

• Should keep wireless devices at least six

inches from the pacemaker.

• Should NOT place wireless devices directly

over the pacemaker, such as in a breast

pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless devices.

Electromagnetic elds (EMF)

This VTech product complies with all standards

regarding electromagnetic fields (EMF).

If handled properly and according to the

instructions in this user’s manual, the product

is safe to be used based on scientific evidence

available today.

• DO NOT expose it to direct sunlight or

moisture.

• Avoid dropping the product or treating it

roughly.

• Clean with a soft cloth.

• DO NOT immerse the camera unit in water

and do not clean it under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the camera unit is dry before you

connect it to the mains again.

Produktspecifikationer

Varumärke:	VTech
Kategori:	Babyvakt
Modell:	VM990
Typ av operation:	Touch
Färg på produkten:	Roestkleur
Bredd:	500 mm
Höjd:	1300 mm
Ljudnivå:	53 dB
Årlig-energiförbrukning:	- kWu
Snäll:	Hangend
Motoreffekt:	54 W
Avgasanslutningsdiameter:	150 mm
Husmaterial:	Roestvrijstaal
Maximal utsugskapacitet:	400 m³/uur
Typ lampa:	LED
Soort vetfilter:	Houtskool
Strömlampa:	9 W