Walrus Audio Monumental Bruksanvisning

Läs nedan 📖 manual på svenska för Walrus Audio Monumental (5 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/5
*Only use a 9 volt DC, Center Negative, 100mA to power the pedal.
The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
Daisy chain power supplies are not recommended.
Got questions or need a repair?
Email help@walrusaudio.com to talk with a real live human about your Walrus gear!
This product comes with a limited lifetime warranty.
Click Here for more info.
The Monumental Harmonic Stereo Tremolo is an analog, optical tremolo inspired by the
beautifully jagged, red-sand desert landscape of Monument Valley. The Monumental is
capable of blending between harmonic and standard tremolo in stereo to produce rich,
luscious, warm pulsating modulation producing valleys as smooth or as jagged as the real
ones that our dear mother nature created long ago.
VOL: Use to adjust the overall volume of the left and right channels. Counterclockwise
is less volume, clockwise is maximum volume. You are able to achieve +10dB of clean
gain at maximum volume.
SHAPE: Use to change the waveshape of the LFO.
Sine Square Saw Ramp Bump Random
PAN: Control the stereo spread of the left and right channels.
Counterclockwise is your standard tremolo sound, the left and
right channels have the same LFO. Turning the control
clockwise will offset the phase of the right LFO to introduce
stereo spread. Fully clockwise is maximum panning
with the right channel LFO being 180 degrees out of
phase from the Left LFO.
CONTROLS
0% paNNed 50% paNNed 100% paNNed
RATE: Finely adjust the speed of the LFO (TAP LED
will always indicate the rate). Counterclockwise
for slower speeds, clockwise for faster speeds.
DEPTH: Control the intensity of the tremolo effect.
Fully Counterclockwise will give you no tremolo
effect, clockwise will give you the maximum
tremolo effect.
S-B-H: Use this control to blend between
standard and harmonic tremolo modes.
In , all frequencies get affected at the Standard
same time.
In , the High frequencies and Low Harmonic
frequencies are offset from each other - When
high is on, low is off. When high is off, low is on.
Pro Tip: Experiment with the S-B-H knob in
combination with the Pan knob to create
interesting polyrhythmic sounds.
TAP/RAMP: Tap this switch to set the rate of the LFO. Your taps are averaged for more
accurate timing, so more taps = more accurate timing. Tap the switch once to reset the
starting point of the LFO. Holding down the tap tempo switch will engage the ramp”
feature. While holding down the switch you can adjust the rate knob to determine where
the LFO ramps to. If you set the ramp speed slower than your current tempo, it will ramp
down, then back up to your set tempo upon release. If you set your ramp speed higher
than your current tempo, then it will ramp up, then back down to your current tempo
upon release. This can be saved per preset and will also work in live mode.
BYPASS: Press this control once to turn the pedal bypass/activate
the effect. Hold down the Bypass switch when the pedal is active
to edit the expression parameters (See Expression).
CONTROLS
TAP DIVISION BUTTON: Use this control to
determine the subdivision of the LFO based
on the current rate, which can be set via the
RATE control or the TAP TEMPO. Tap division
is always active.
Available divisions are:
Quarter Note Quarter Note Triplet Eighth Note
Eighth Note Triplet Sixteenth Note
STANDARD MODE
BLENDED
(S-B-H knob fully counterclockwise)
(S-B-H knob begins to separate low & high frequencies)
(S-B-H knob fully clockwise)
HARMONIC MODE
LOW FREQUENCY
HIGH FREQUENCY
LOW FREQUENCY
HIGH FREQUENCY
LOW FREQUENCYHIGH FREQUENCY
PRESETS: The Monumental has three onboard presets
with an additional live mode. Each preset can save and
recall every parameter available on the pedal. Press both
the Bypass Switch and Tap Tempo Switch simultaneously
to cycle through the available presets (Red, Green, Blue,
and White “live”).
PRESET RESET: Hold both stomp switches while applying
power to the pedal for lo
more se
When you are on a preset and you change a
parameter, the bypass LED will change color to
purple, indicating a change has been made. You can
then turn the control and the bypass LED will return
to the preset color when the control is at the saved
position. Once you have determined what sound
you want saved for the preset, hold down both
footswitches to save the preset (the bypass LED
will return to the preset color).
Live mode will always return to the current
knob positions on the face of the pedal.

Produktspecifikationer

Varumärke: Walrus Audio
Kategori: Inte kategoriserad
Modell: Monumental

Behöver du hjälp?

Om du behöver hjälp med Walrus Audio Monumental ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Walrus Audio Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer