Whirlpool AWT 2074 Bruksanvisning

Whirlpool tvättmaskin AWT 2074

Läs nedan 📖 manual på svenska för Whirlpool AWT 2074 (14 sidor) i kategorin tvättmaskin. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/14

115

QUICK REFERENCE GUIDE GB

BEFORE USING THE APPLIANCE FOR THE FIRST TIME:

• IMPORTANT: MAKE SURE YOU HAVE READ THE INSTALLATION INSTRUCTIONS.

• IMPORTANT: REMOVE THE TRANSPORT SCREWS AND THE TRANSPORT BRACKET.

• First wash cycle without laundry:

1. Open the tap(s).

2. Close the drum flaps.

3. Pour a small amount of detergent (about 30 ml) into the detergent dispenser

compartment .

4. Close the lid.

5. Select a short wash programme and a low spin speed (see programme chart).

6. Switch on the appliance.

This will remove any water remaining in the machine from the manufacturer’s test run.

NORMAL DAILY USE:

1. Open the tap(s).

2. Sort the laundry according to fabric type and colour and load the machine.

3. Close the drum flaps.

4. Add detergent and any additives required into the dispenser.

5. Close the lid.

6. Select the programme, temperature, spin speed and special options.

7. Switch on the appliance.

Read these user instructions carefully to learn about all the functions of your washing

machine.

116

GB CONTENTS

INSTALLATION INSTRUCTIONS PAGE 117

WASHING MACHINE AND ACCESSORIES PAGE 120

PROTECTING THE ENVIRONMENT PAGE 121

SAFETY INSTRUCTIONS PAGE 121

TRANSPORT / HANDLING PAGE 121

PREPARING THE WASH PAGE 122

DETERGENT AND ADDITIVES PAGE 123

DYEING AND BLEACHING PAGE 123

STARCHING PAGE 123

REMOVING THE FOREIGN BODY TRAP PAGE 124

DRAINING RESIDUAL WATER PAGE 124

MAINTENANCE AND CLEANING PAGE 125

TROUBLESHOOTING GUIDE PAGE 127

AFTER-SALES SERVICE PAGE 128

117

HOW TO UNPACK THE APPLIANCE

1. Cut and remove the shrink-wrap.

2. Remove the top protection and the protection corners.

3. Remove the bottom protection by tilting and

turning the appliance on one rear bottom corner.

4. Open the lid by pulling at the handle. Remove the

polystyrene cushion.

HOW TO REMOVE THE TRANSPORT

SCREWS AND THE TRANSPORT BRACKET

The appliance is fitted with the transport screws and

the transport bracket to prevent internal damage while

being moved.

Before using the appliance, the transport bracket

at the back MUST be removed.

1. Unscrew the two screws A and the four screws B

with a flat screwdriver or a N°8 hex nut screwdriver.

2. Remove the transport bracket.

3. Replace the four outer screws B into the machine

again and tighten.

4. Tear off the two stop plugs C from the hose holder

and clip them into the openings of the machine

Note: In case of future moves, always transport the

washing machine upright.

Keep the transport bracket for future use.

INSTALLATION

•Install the appliance on a solid and level floor

surface close to electrical, water and drain

connections.

•Make sure that all feet are stable and resting on

the floor and then check that the appliance is

perfectly level (use a spirit level).

•If the floor is uneven, adjust the levelling feet as

required (do not insert pieces of wood, cardboard

etc. under the feet).

•The appliance can be installed in a 40 cm width

and 63 cm depth space.

Note: It is important to avoid blocking the openings on

the underside of the appliance when installing on a

carpet floor.

ADJUSTMENT OF THE APPLIANCE

1. To move the appliance into its operating position:

Pull the mobility lever situated on the bottom of

the front (optional on certain models) a little bit by

hand and pull it in the final driving position by foot.

Afterwards push the mobility lever back into the

original, stable position. The front feet can be

adjusted in order to level the appliance.

2. Loosen the locknut using a wrench.

3. Adjust the height of the foot, turning it by hand.

4. Tighten the locknut by turning it anti-clockwise

towards the appliance casing.

IMPORTANT: Do not run the appliance while the

mobility lever is pulled and the appliance isstanding on

the trolleys.

INSTALLATION INSTRUCTIONS

Produktspecifikationer

Varumärke:	Whirlpool
Kategori:	tvättmaskin
Modell:	AWT 2074
Vikt:	3170 g
Bredd:	292 mm
Djup:	220 mm
Höjd:	108 mm
Ljudnivå:	32 dB
Förpackningens vikt:	3670 g
Förpackningens bredd:	362 mm
Djuppackning:	305 mm
Förpackningshöjd:	197 mm
Original bildförhållande:	4:3
USB-kontakttyp:	Mini-USB B, USB Type-A, USB Type-B
Ethernet LAN:	Ja
Videolägen som stöds:	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Medföljande kablar:	VGA
Typiskt kontrastförhållande:	15000:1
Inkluderar AC-adapter:	Ja
Marknadspositionering:	Draagbaar
Projektorns ljusstyrka:	3500 ANSI lumens
Projektionsteknik:	DLP
Projektorns inbyggda upplösning:	XGA (1024x768)
Lämplig för skärmstorlekar:	- "
Projektionsavståndsmål:	- m
Antal färger:	1.073 biljoen kleuren
VGA (D-Sub) port(ar):	2
Antal HDMI-portar:	1
Typ av seriell anslutning:	RS-232
Audio-ingan (L, R):	1
Kompositvideoingång:	1
S-videoingång:	1
DVI-port:	Nee
Antal Ethernet LAN (RJ-45)-portar:	1
Fokus:	Handmatig
Brännvidd:	- mm
Ljuskällans livslängd:	3500 uur
Monteringsalternativ för kabellås:	Ja
Kabellåsspårtyp:	Kensington
Inbyggda högtalare:	Ja
Genomsnittlig effekt:	2 W
Antal inbyggda högtalare:	2
Strömförbrukning (i standby):	- W
Bildförhållanden som stöds:	4:3, 5:4, 16:9, 16:10
Zoomförhållande:	1.1:1
Kastförhållande:	1.9 - 2.2:1
Analog signalformat:	NTSC, PAL, SECAM
Full HD:	Nee
HDCP:	Nee
RS-232 port:	1
3D:	Ja
HDMI-version:	1.4
Ljud (L,R) ut:	1
Ljuskällans livslängd (sparläge):	5000 uur
Förinställda lägen:	Beige wall, Blackboard, Bright, Presentation, Whiteboard
Ljudnivå (ekonomiläge):	30 dB
Horisontell synkronisering (min):	15 kHz
Horisontell synkronisering (max):	91 kHz
Vertikal synkronisering (min):	24 kHz
Vertikal synkronisering (max):	120 kHz
Projektorns ljusstyrka (ekonomiläge):	3200 ANSI lumens
Fjärrkontroll ingår:	Ja
Typ produkt:	Projector met normale projectieafstand