Whirlpool AWT 2359 Bruksanvisning

Whirlpool tvättmaskin AWT 2359

Läs nedan 📖 manual på svenska för Whirlpool AWT 2359 (48 sidor) i kategorin tvättmaskin. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/48

CONTENTS

BEFORE USING THE WASHING MACHINE

FIRST WASH CYCLE

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

DESCRIPTION OF THE WASHING MACHINE

PREPARATION OF THE WASHING

DETERGENTS AND ADDITIVES

PROGRAMME SELECTION

CLEANING THE FOREIGN BODY TRAP

DRAINING RESIDUAL WATER

CARE AND MAINTENANCE

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

TRANSPORT AND HANDLING

INSTALLATION

ELECTRICAL CONNECTION

3GB10281.fm Page 1 Wednesday, April 21, 2004 6:05 PM

GB 2

BEFORE USING THE WASHING MACHINE

1.Remove the packaging and check

a. Cut and remove the shrink-wrap.

b. Remove the top protection and the protective

corners.

c. Remove the bottom protection by tilting and

turning the washing machine on one rear bottom

corner.

d. Open the lid by pressing it slightly down while raising

the handle. Remove the polystyrene cushion.

e. Remove the blue protective film from the panel

(depending on model).

•After unpacking, make sure that the washing

machine is undamaged. If in doubt, do not use the

washing machine. Contact After-Sales Service or

your local retailer.

•Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children;

they are potentially dangerous.

2.Remove the transport bracket

•The washing machine is fitted with transport

screws and a transport bracket to prevent

damage during transport. Before using the

washing machine you must remove the

transport bracket (see “Installation/Remove

the transport bracket”).

3.Install the washing machine

•Place the washing machine on a flat and stable

floor surface.

• Adjust the feet to ensure that the machine

is stable and level (see “Installation/Adjust

the feet”).

4.Water supply

•Connect the water supply inlet hose in

accordance with the regulations of your local

water company (see “Installation/Connect the

water inlet hose”).

•Water supply: Cold water only

•Tap: 3/4” threaded hose connection

•Pressure: 100-1000 kPa (1-10 bar).

For Great Britain & Ireland only:

•Water inlet: hot and cold fill.

The warm water inlet temperature must not

exceed 60° C.

5.Drain hose

•Connect the drain hose to the siphon or hook it

over the edge of a sink with the “U” bend (see

“Installation/Connect the water drain hose”).

•If the washing machine is connected to a built-in

drainage system, ensure the latter is equipped

with a vent to avoid simultaneous loading and

draining of water (siphoning effect).

6.Electrical connection

•Electrical connections must be carried out by a

qualified technician in compliance with the

manufacturer’s instructions and the current

standard safety regulations.

•The technical data (voltage, power and fuses) are

given on the rating plate on the rear of the

washing machine.

•The washing machine must be connected

exclusively by means of a socket with an earth

connection in accordance with current

regulations. The washing machine must be

earthed by law. The manufacturer declines all

liability for damage to persons or property

deriving directly or indirectly from failure to

observe the directions.

•Do not use extension leads or multi sockets.

•Before any maintenance on the washing machine

disconnect it from the mains supply.

•Access to the mains plug or to disconnection

from the mains supply via a double-pole switch

must be ensured at all times following the

installation.

•Do not operate the washing machine if it has

been damaged during transport. Inform the

After-Sales Service.

•Mains cable replacement is only to be carried out

by After-Sales Service.

•The washing machine must be connected to an

effective earthing installation, in compliance with

the regulations in force. In particular, washing

machines installed in premises containing a

shower or a bath must be protected by a

differential residual current device of at least 30

mA. Earthing the washing machine is obligatory

under the law. The manufacturer declines all

liability for damage to persons or property

deriving either directly or indirectly from failure

to observe the directions above.

•The washing machine may only be used in the

household for the prescribed uses.

Dimensions:

Width: 400 mm

Height: 900 mm

Depth: 600 mm

3GB10281.fm Page 2 Wednesday, April 21, 2004 6:05 PM

GB 3

FIRST WASH CYCLE

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

1.Packing

•The packaging materials are 100% recyclable

and bear the recycling symbol . Adhere to

local regulations when disposing of packaging

material.

2.Energy saving tips

•Achieve the best use of energy, water, detergent

and time by using the recommended maximum

load size.

•Do not exceed the detergent dosages indicated

in the manufacturer’s instructions.

•The Eco Ball - a special system in the outlet - will

prevent detergent loss from the drum to avoid

detergent loss into the environment.

•Use “Prewash” for heavily soiled laundry only!

Save detergent, time, water and energy

consumption by not selecting “Prewash” for

slight to normally soiled laundry.

•Pretreat stains with stain remover or soak dried

in stains in water before washing to reduce the

necessity of a hot wash program.

•Save energy by using a 60°C instead of a 90°C

wash programme or a 40°C instead of a 60°C

wash programme.

•Save energy and time by selecting a high spin

speed to reduce the water content in laundry

before using a tumble dryer (for machines with

adjustable spin speed).

3.Disposing of packaging and old washing

machines

•The washing machine is built from reusable

materials. The washing machine must be

disposed of in compliance with current local

waste disposal regulations.

•Before scrapping, cut of the power cable so that

the washing machine cannot be connected to the

mains.

•Remove detergent from compartment if you

intend scrapping your washing machine.

4.Child safety

•Children must not be allowed to play with or in

the washing machine.

5.General recommendations

•Do not leave the washing machine connected

when not in use. Turn off the tap.

•Before cleaning or carrying out maintenance

switch off the washing machine and disconnect it

from the mains supply.

•To clean the outside of the washing machine, use

a neutral detergent and a damp cloth.

•Do not use abrasive detergents.

•Do not attempt to force the lid open.

•If necessary, the power cable may be replaced

with an identical one obtained from our After-

Sales Service. The power cable must only be

replaced by a qualified technician.

6.EC Declaration of Conformity

•This washing machine has been designed,

constructed and distributed in compliance with

the safety requirements of EC Directives:

73/23/EEC Low Voltage Directive

89/336/EEC EMC Directive

93/68/EEC CE Marking Directive

We recommend that the first wash cycle be carried out empty. This will remove any residual water used

in the factory checks.

1.Turn on the tap.

2.Close the drum flaps.

3.Pour a small amount of detergent (about 30 ml) into the detergent dispenser .

4.Select a short programme (see programme chart).

5.Switch on the machine.

6.Press the “On/Off” button.

3GB10281.fm Page 3 Wednesday, April 21, 2004 6:05 PM

Produktspecifikationer

Varumärke:	Whirlpool
Kategori:	tvättmaskin
Modell:	AWT 2359
Färg på produkten:	Zwart
Vikt:	1480 g
Sladdlängd:	450 m
Snäll:	Alles-in-één vloeistofkoeler
Ljudnivå (hög hastighet:	35 dB
Typ av förpackning:	Doos
Monteringsverktyg:	Ja
Medföljande kablar:	4-pin
Material:	Aluminium
Hållbarhetscertifikat:	Federal Communications Commission (FCC), REACH, RoHS
Luftflöde:	131.93 m³/uur
Antal per paket:	1 stuk(s)
Antal fans:	2 ventilator(en)
Färg på belysningen:	Multi
Rotationshastighet (max):	2000 RPM
Slangdiameter:	71.5 mm
Inklusive skruvar:	Ja
Rotationshastighet (min):	600 RPM
Antal lysdioder:	12
Belysning LED:	Ja
Lämplig plats:	Computer case, Processor
Kompatibla processorer:	Intel Core i3, Intel Core i5, Intel Core i7, Intel Core i9
Grundläggande plåtmaterial:	Koper
Ventilator diameter:	120 mm
Pumpmotorns hastighet:	1600 RPM
Pumpmotorhastighet (max):	3200 RPM
Ventilator 2 diameter:	120 mm
Fläktspänning:	12 V
Maximalt lufttryck:	2.9 mmH2O
Stöd för pulsbreddsmodulering:	Ja
Typ av lager:	Hydrodynamische lager (HDB)
Fläktkontakt:	4-pin
Installationsinstruktion:	Ja
Fläkthastighet (max):	2000 RPM
Vattenblockmaterial:	Koper
Radiatormaterial:	Aluminium
Pumpmotorhastighet (min):	1600 RPM
Fläkthastighet (min):	600 RPM
Pompspänning:	12 V
Pumpström:	0.35 mA
Pumpströmförbrukning:	4.2 W
Fan Dikhaid:	25 mm
Kylarens bredd:	121 mm
Kylarens djup:	272 mm
Kylarens höjd:	27.5 mm
Energiförbrukning ventilation:	2.52 W
Fläktlagerteknik:	Hydrodynamische lager (HDB)
Från nuvarande:	0.21 A
Pompkontakt:	4-pin
Inkluderar termisk dyna:	Ja
Lagerteknik för pumpar:	Keramische lager
Fläkt 2 rotationshastighet (min):	600 RPM
Fläkt 2 rotationshastighet (max):	2000 RPM
Fläkt 2 ljudnivå (hög hastighet):	35 dB
LED-anslutningstyp:	4-pin
Led spänning:	6.7 V
LED-strömförbrukning (fläkt):	2.7 W
LED-strömförbrukning (pump):	4 W
Rörets innerdiameter:	52.3 mm