Whirlpool CEM2745FQ Bruksanvisning

Whirlpool Torktumlare CEM2745FQ

Läs nedan 📖 manual på svenska för Whirlpool CEM2745FQ (6 sidor) i kategorin Torktumlare. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/6

Removing Greenwald Coin Slides from Coin Boxes

Tools Needed

5/16" socket wrench 5/16" open end wrench

1. Disconnect coin slide

harness and ground jumper

With the service door open, disconnect

the coin slide harness by pressing down

on the locking tab and pulling apart. Also

disconnect the ground jumper.

2. Loosen coin slide bolt

Using a 5/16" socket wrench or 5/16" open

end wrench, loosen the coin slide bolt. Set

the bolt aside.

W11032801B

3. Remove coin slide

Remove the coin slide by pushing up, then

pulling out (it may require some twisting and

turning).

6. Tighten coin slide bolt,

reattach harness and

ground jumper, and test

Align the long bolt, insert, and tighten using

a 5/16" socket wrench or 5/16" open end

wrench. Reattach the harness and ground

jumper and test.

4. Change vend price (see

page 2 of this instruction)

See page 2 of this instruction for information

on how to change the vend price.

5. Reinsert coin slide

Reinsert the coin slide in the coin box by

pushing the slide as far back as possible,

and then pushing down to lock it in place.

Locate the threaded bolt hole.

Changing the Vend Price on Greenwald Coin Slides

Tools Needed

Phillips screwdriver Quarters (up to 8) Coin slot plugs

(if needed; eight [8]

are provided)

1. Remove spring from coin slide

Remove the one large spring from the coin

slide assembly.

3. Separate coin slide

assembly into three sections

Remove the two screws holding the cover

and switch extension to the assembly (A).

With the screws removed, the assembly

breaks down into three components (and

the spring).

4. Remove two screws

holding plug retainer

With the slide fully forward, remove the

two screws holding the plug retainer.

2. Push slide fully forward

Fill the empty coin slots with quarters

and push the coin slide fully forward.

The quarters will drop free. Do not retract

the coin slide until instructed.

Reassemble the cover and switch extension

to the coin slide. Secure with the screws

removed in Step 3. Note the location

of the bolt within the slider on the extension

(see illustration). This is important to the

function of the slide.

5. Turn over assembly and

adjust locations and number

of coin slot plugs

With the retainer removed, turn over the

assembly and adjust the locations and

number of coin slot plugs as needed.

Keep and store extra plugs, as they may

be needed in the future.

6. Replace plug retainer

Replace the plug retainer. Note that the word

“UP” is embossed on the visible side (see

illustration). Secure with the screws removed

in Step 4. It is helpful to hold this in place

with one hand while the screws are replaced

on the opposite side.

7. Reassemble cover

and switch extension

8. Insert quarters

and test for function

Insert the appropriate number of quarters

in the coin slide and test for function. Make

sure the slider moves freely and engages

the switch.

9. Reattach spring

Reattach the single spring and insert the coin

slide assembly back into the meter case per

the instructions on page 1.

Retirer les glissières à monnaie Greenwald des boîtes à monnaie

Outillage nécessaire

Clé à douille de 5/16" (8 mm) Clé plate de 5/16" (8 mm)

2. Desserrer le boulon

de la glissière à monnaie

À l’aide d’une clé à douille de 5/16" (8 mm)

ou d’une clé plate de 5/16" (8 mm), desserrer

le boulon de la glissière à monnaie. Mettre

le boulon de côté.

3. Retirer la glissière à monnaie

Retirer la glissière à monnaie en tirant vers

le haut, puis vers l’extérieur (il sera peut-être

nécessaire de tourner et secouer la glissière

à monnaie).

6. Serrer le boulon de la glissière

à monnaie, rebrancher le

faisceau et le cavalier de terre

et contrôler

Aligner le long boulon, l’insérer et le serrer en

utilisant une clé à douille de 5/16" (8 mm) ou

une clé plate de 5/16" (8 mm). Rebrancher le

faisceau et le cavalier de terre, puis contrôler

le fonctionnement.

4. Modi er le prix de vente

(voir page 4 de cette feuille

d’instructions)

Consulter page 4 de cette feuille

d’instructions pour savoir comment modi er

le prix de vente.

5. Replacer la glissière à monnaie

Replacer la glissière à monnaie dans la boîte

à monnaie en la poussant dans l’espace

aussi loin que possible, puis en appuyant

vers le bas pour la verrouiller en place.

Repérer le trou de boulon  leté.

1. Débrancher le faisceau

de la glissière à monnaie

et le cavalier de terre

En gardant la porte de service ouverte,

débrancher le faisceau de la glissière à

monnaie en appuyant sur la languette de

verrouillage et en tirant sur les deux parties.

Aussi débrancher le cavalier de terre.

Produktspecifikationer

Varumärke:	Whirlpool
Kategori:	Torktumlare
Modell:	CEM2745FQ
Färg på produkten:	Zwart
Vikt:	95 g
Bredd:	46 mm
Djup:	99 mm
Höjd:	21 mm
Snäll:	Draagbare streepjescodelezer
Bluetooth-version:	4.0
Anslutningsteknik:	Draadloos
Typ av strömkälla:	Batterij/Accu
Medföljande kablar:	USB
Bildsensortyp:	LED
Anslutningsområde:	30 m
Förvaringstemperatur:	-40 - 70 °C
Stroomverbruik:	1000 mA
Streckkoder som stöds (1D):	Codabar, Code 11, Code 128, Code 39, Code 93, GS1-128 (UCC/EAN-128), Interleaved 2 of 5, MSI, Plessey, PostBar, Telepen
Standardgränssnitt:	Bluetooth
Typ av skanner:	1D/2D
Drifttemperatur (TT):	0 - 50 °C
Relativ luftfuktighet i drift (VV):	5 - 95 procent
2D (matris och staplade) streckkoder stöds:	Aztec Code, Data Matrix, MaxiCode, Micro QR Code, MicroPDF417, PDF417, QR Code
Läshastighet (max):	300 lezingen/s
Arbetsavstånd:	450 mm