Zanker kht 6111 x Bruksanvisning

Zanker Fläktkåpa kht 6111 x

Läs nedan 📖 manual på svenska för Zanker kht 6111 x (24 sidor) i kategorin Fläktkåpa. Denna guide var användbar för 11 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/24
Operating Instructions
Mode d’emploi
Bedienungsanleitung
Gebruiksaanwijzing
Istruzioni per l’uso
Manual de instrucciones
Manual de instruções
2
GB
GENERAL INFORMATION
This canopy hood is designed to be fixed to any rigid vertical surface, over a gas or electric hotplate
and can be used either in the extraction mode (ducted to the outside) or in the recircu-lation mode
(internal recycling). All cookers hood perform better when used in evacuation mode. During winter
time it may be convenient to use the hood in the recycling mode to avoid heat loss from the kitchen.
Before starting the installation, consideration should be given to the difficulties to be found
during installation. The installation work must be undertaken by a qualified and competent
person in conformity to the rules concerning the evacuation of contaminated air.
The manufacturer disclaims all liability for any damage or injury caused as a result of not
following the instructions for installation contained in the following text.
1 - SAFETY WARNINGS
1.1 - When used in the extraction mode, the cooker hood ducting must not be connected to a flue
which is used for exhausting fumes from appliances supplied with energy other than electric,
such as a central heating flue or water heating flue.
1.2 - Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage
on the rating plate inside the hood.
1.3 - Connect the cooker hood to the mains via a bipolar switch which has 3mm clearance between
the contacts.
1.4 - For cooker hoods featuring an earth cable, make sure the electric plant of your house is correctly
earthed.
1.5 - Appliance in class II are provided with a double insulation; therefore do not connect then through
earthed plugs but through simple bipolar plugs.
1.6 - When installed, the hood must be positioned at least 65cm above the hotplate.
1.7 - Never do flambé cooking under this cooker hood.
1.8 - Never leave frying pans unattended during use as overheated fat and oil may catch fire.
1.9 - Before carrying out any kind of maintenance or cleaning, disconnect the hood from the mains
supply.
1.10 - If the room where the cooker hood is to be used contains a fuel burning appliance such as a
central heating boiler then this must be of the room sealed or balanced flue type. If other types
of flue or appliance are fitted, ensure that there is an adequate supply of air into the room. When
the cooker hood is used in conjunction with appliances supplied with energy other than electric,
the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back
into the room by the cooker hood.
1.11 - The appliance must be positioned so that the plug is accessible.
1.12 - If the supply cord is damaged, it must be replaced by a special cord or assembly available from
the manufacturer or its service agent.
2 - INSTALLATION INSTRUCTIONS
Some installation systems require the opening and removal of the metal grille panel.
2.1 - Instructions for opening and removing the metal grille panel
To open the grille panel, press inwardly on the two slider catches at each side of the grille panel and
the grille will pivot down.
To remove the metal grille, pull forward on the right hand side so that the hinge pin on the back of
the grille will be released from the slot in the side of the casing.
3
GB
2.2 - Wall cabinet fixing
a - Predrilled wall cabinet: fix the hood onto the wall cabinet base panel using the four screws 4.2
x 45 mm (supplied with the fixing kit).
It is not necessary to open the metal grille.
b - No predrilled wall cabinet:
b.1 - If the hood is provided with a paper fixing template, follow the instructions.
b.2 - If the hood is not provided with a paper fixing template, position the hood on the wall
cabinet base panel and pilot drill the 3.5 x 16 mm screws (not supplied with the fixing kit)
from the inside onto the wood.
2.3 - Wall mounting
a - Drill two Ø 8 mm holes on the wall using the paper template, insert two rawl plugs and two 4.2
x 44,4 mm screws leaving 5 mm untightened. Open the metal grille panel, hook the hood on and fully
tighten the screws.
b - If the hood is not provided with a paper fixing template, drill two Ø 8 mm holes (see draw.), insert
the plugs and screws, proceeding as directed under paragraph a.
c - For wall mounting using wallbrackets (optional), follow the instructions of the fixing template.
d - Pay attention to the safety regulation of point 1.6.
2.4 - Choice of operating mode
a - Evacuation mode
To check that the hood is set up for evacuation, open the grille panel and make sure that the conver-
sion lever or the change-over knob on the centrifugal unit is in the DUCTING position. The charcoal
filter is not required.
For ducting to the outside, the hood is supplied with a rear and top outlet. A flange spigot of 100 mm
diameter (120 mm in certain models) is usually fitted on the top outlet and a blanking plug on the rear
outlet. If you choose to duct the hood from the rear of the casing, you should invert the position of
the flange and of the blanking plug. Pay attention to the safety regulation 1.1.
b - Internal recirculation mode
To check that the hood is set up for recycling, open the grille panel and make sure that the conversion
lever or the change-over knob on the centrifugal unit is in the RECYCLING position.
The charcoal filter is to be fitted. To fit the charcoal filter, support the filter with one hand and turn
the thumb screw through the centre of the charcoal filter. If the filter is of the interlocking type, turn
the filter clockwise. The hood can remain connected to the outside.
2.5 - Electrical connection and working test
1 - The safety measures 1.2, 1.3, 1.4 and 1.5 of paragraph 1 are to be strictly observed.
2 - Once the electrical connection has been completed, check that the worktop illumination, motor
and speeds work properly.
3 - OPERATION
3.1-Controls are located on the right hand side of the front to operate worktop illumination and select the
most suitable working speed for your cooking. To increase the area of extraction, the glass visor
should be pulled open. The top speed should be used when frying or cooking foods with strong
odours, while a lower speed can be used for normal cooking.
To obtain the best performance from your hood, turn it on before you start cooking and leave it
running for a few minutes after your cooking is over to clear the air.
3.2-Pay attention to safety regulations 1.7 and 1.8.

Produktspecifikationer

Varumärke: Zanker
Kategori: Fläktkåpa
Modell: kht 6111 x

Behöver du hjälp?

Om du behöver hjälp med Zanker kht 6111 x ställ en fråga nedan och andra användare kommer att svara dig


Fläktkåpa Zanker Manualer

Zanker

Zanker ZKC6141X Bruksanvisning

21 September 2024
Zanker

Zanker ZKC6244X Bruksanvisning

31 Augusti 2024
Zanker

Zanker ZKC 6244 Bruksanvisning

17 Juli 2024
Zanker

Zanker ZKC 9141 Bruksanvisning

17 Juli 2024
Zanker

Zanker krt 260 x rvs Bruksanvisning

16 Juli 2024
Zanker

Zanker krc 60 x rvs Bruksanvisning

16 Juli 2024
Zanker

Zanker krt 60 b n w Bruksanvisning

16 Juli 2024
Zanker

Zanker krc 90 x Bruksanvisning

16 Juli 2024
Zanker

Zanker krp 60 Bruksanvisning

16 Juli 2024
Zanker

Zanker kht 6111 x Bruksanvisning

16 Juli 2024

Fläktkåpa Manualer

Nyaste Fläktkåpa Manualer

Neff

Neff D61MAC1X0B Bruksanvisning

27 Oktober 2024
Klarstein

Klarstein 10033709 Bruksanvisning

27 Oktober 2024
Halifax

Halifax FTHI740K Bruksanvisning

27 Oktober 2024
Hoover

Hoover HDTI6500/1X Bruksanvisning

27 Oktober 2024
Heinner

Heinner HTCH-440FS Bruksanvisning

27 Oktober 2024
ATAG

ATAG WG411V Bruksanvisning

27 Oktober 2024
Broan

Broan BKDB136WW Bruksanvisning

27 Oktober 2024
XO

XO R30SC Bruksanvisning

26 Oktober 2024
IKEA

IKEA DATID HW570 Bruksanvisning

24 Oktober 2024
Candy

Candy CDG6MB Bruksanvisning

24 Oktober 2024