Accell UltraAV K072C-013B Bruksanvisning

Accell mottagare UltraAV K072C-013B

Läs nedan 📖 manual på svenska för Accell UltraAV K072C-013B (2 sidor) i kategorin mottagare. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
READ ME FIRST – SETUP INSTRUCTIONS
Thank you for purchasing the Accell UltraAV HDMI Distribution
Amplifi er. This product is designed to provide an exceptional
performance and value. Please review the manual before
operating and retain for future reference.
- CAUTION -
1. Ensure the unit has suffi cient
ventilation. Do not cover
ventilation openings. Do not install
in a confi ned space.
2. Do not operate near source
of heat. Do not stack on to p,
underneath or between other heat
generating unit/s including other
amplifi ers.
3. Unplug power adapter if not
used for an extended period.
4. To prevent damage from power
surges, the unit should be plugged
into a surge protector or surge pro-
tected power source.
5. Do not use near liquid or areas
of heavy moisture.
6. Clean unit with a clean and dry
cloth only.
7. This unit cannot be serviced in
the fi eld. Contact Accell if service is
required.
8. Do not open case, risk of shock -
shock hazard.
9. Do not modify power cord or use
the product if the power cord is
damaged.
Introduction
The UltraAV 4x4 HDMI Matrix and Distribution Amplifier accepts signals
from up to 4 HDMI enabled audio/video sources and distributes the
signal to up to 4 HDMI enabled displays. The matrix can be configured to
send any input to a HDMI displays, monitors, projectors or TV’s.ny
Over-Current and Over-Voltage Protection
The circuit boards are equipped with both oltage over-current and over-v
protection and will automatically power down if encountered. The circuit
boards will restore automatically once the excessive current or voltage
has passed.
Package Contents
●HDMI Distribution Amplifier (Matrix) ●Power Adapter
●Remote Control (with battery) ●Owner’s Manual
●CD-ROM (for RS-232 control)
Model Number:
K072C-013B
UltraAV
®
HDMI 4x4 Matrix and
Distribution Amplifier
Setup
With the matrix power switch in the OFF position, connect an HDMI High
Speed cable from the HDMI Output of the most commonly used audio/
video source to the HDMI Input 1 located on the rear of the matrix.
Similarly, connect the remaining source devices to the HDMI Input rts Po
on the matrix.
Tips: Use the shortest length HDMI cables possible in each point
in the installation. Use only High Quality and High Speed HDMI
cables.
Next, connect an HDMI cable to the HDMI Output Port 1 on the rear of
the matrix. Connect the other end to the HDMI Input Port of the displ ay
device. Similarly, connect the remaining HDMI Output Ports from the
matrix to the other displays.
The matrix has internal memory that stores the system
information for faster switching. Please follow the steps in the
order listed: Turn ON the displays and ensure they are awake (not in
standby mode). Check the displays INPUT setting to ensure the correct
HDMI port is active.
Turn on the source devices and ensure they are awake (not in standby
mode). Connect the power adapter to the matrix. Plug the power
adapter into a surge protected AC power outlet. Turn the matrix power
switch to the ON position.
The matrix has a low power d w and is intended to be left on. If ra
the matrix is turned off, start up the system as noted above. If new
hardware is added, please perform a RESET.
To RESET the matrix, turn off the display and source devices. Power off
the matrix and unplug the power adapter from the rear of the matrix.
Wait 20 minutes for the memory of the system configuration inside of
the matrix to be deleted. llow the setup instructions above to correctly Fo
initiate the setup.
HDMI 4x4 Matrix and Distribution Amplifier
Model: K072C-013B
Specifi cations
● Independently access 4 HDMI Sources from 4 HDMI Displays
● Supports HD resolutions up to 1080P and 3D
● HDMI 1.4a, HDCP 1.2 compliant
● Input video signal: 5v p-p, Input DDC signal: 5v p-p (TTL)
● Data transfer speed of 6.75Gbps (2.25Gbps/channel)
● Audio formats supported: S-HD 7.1, Dolby TDT rue-HD 7.1
● Deep color up to 36-bit
● RS232 Port for control
● Maximum input cable length: Up to 20m (24AWG)
● Maximum output cable length: Up to 20m (24AWG)
● Shelf or surface mountable
● 5V DC, UL Listed power adapter
● Approximate dimensions: 10.9”W x 1.1”H x 6.1”D
277W x 28H x 156D mm
● Operating temperature range: 5 to 131°F (-15 to 55°C)
● Operating humidity range: 5% to 90% RH (no condensation)
LED indicator lights
On initial power on, all LED lights on the matrix should come on solid
blue. All the numerical LED displays will momentarily read ‘0’ and
then change to ‘1’. If less than the maximum number of Displays
are connected to the matrix (not all the outputs are used) the
numerical indicator will indicate ‘0’ for that output and there will be no
corresponding blue LED for the unused output. Blue lights HDMI OUT
will only appear for devices connected. A unused HDMI Input ports will ny
also have its blue LED unlit.HDMI IN
Operation
Manual Control: You can ope te HDMI source switching manually by ra
using the buttons labeled ‘Out” located on the front panel. Press the
button that corresponds to the output that you want to change the HDMI
source on and toggle through until the desired HDMI input source video
is being displayed. A numerical LED indicates which HDMI source input is
being shown on each output (HDTV).
Remote Control: Included with the Matrix is a Remote Control. The
remote control can control the matrix pointing it at the front of the by
matrix, targeting the integrated IR receiver labeled -IR. IR uses line-of
sight between the remote control (or IR-TX) and the receiver. The angle
which the remote will work is at about a 15° degree angle in either
direction to the receiver. If the receiver is postioned such that there
is not line-of -sight, the port labeled “IR Extender” accepts an optional
IR Receiver. This receiver enables line-of-sight if the matrix is out of
position.
LED Indicator Lights
Infrared Control (IR)
The Ultra-IR Adapter Kit (optional) enables the user to control the source
device from the location of the display. The HDMI cable, at the display
end, plugs into the IR Adapter. Next the adapter HDMI connector plugs ’s
into the display. The adapter has a port that accepts an optional IR
receiver (IR-RX). When the IR-RX receives an IR signal from the remote
control, it uses the HDMI cable’s CEC line to send the signal to the switch.
The switch has an IR port that accepts the optional IR transmitter (IR-
TX). The IR-TX sends the signal to the source device.
Note: As the Ultra-IR Adapter uses the CEC channel of the HDMI cable,
the CEC function cannot be used when using this device. rn off CEC or Tu
HDMI Link functionality in the source devices and displays.
Ultra-IR Kit: PN: B164B-001B
Includes IR Adapter: 1 pc.
IR ansmitter (5 ft.): 1 pc.Tr
Dual Frequency: 38KHZ-60KHZ
IR Receiver (5 ft.): 1 pc.
Ultra-IR ceiver andRe
Transmitter Pin
Assignment
Troubleshooting
A. One of the displ does not show a picture or output audiay o.
Q. Check the displays input setting to ensure it is set to receive a signal from the
connected HDMI port.
Q. One or more of the connected displays will not display a picture while one or
more of the displa ys do display a picture:
A1. Turn off the power to the matrix, source and displays. it 1 minute. Turn Wa
the source on. Turn the displays on. Turn the matrix on.
Ultra-IR ceiver (5 ft.)Re
Dual Frequency: 38KHZ-60KHZ
PN: B164B-002B
Ultra-IR ansmitter (5 ft.)Tr
Dual Frequency: 38KHZ-60KHZ
PN: B164B-003B
...troubleshooting continued
A2. The HDMI cables on the non-functonal display/s cannot support their long
length. Use only high-quality High Speed HDMI cables. Keep the cable length as
short as possible. Test by locating the non-working display close to the matrix.
Use a short HDMI cable to connect the matrix to the TV. A working TV using a
short HDMI cable indicates an issue with the HDMI cable.
Q. Get the message “This protocol is not supported” or other error message.
A. See answer A1 abo .ve and repeat the steps outlined
Q. The matrix is not down sampling the video and some of the TV’s are not
displaying a picture.
A1. Go into the TV’s setup and configure the resolution to match all the
connected TV’s. The TV’s should share the same resolution.
A2. In the source devices menu options set the source device to output a
resolution that matches all the connected displays.
Q. My TV resolution are not optimized.’s
A. The matrix will query the displays and provide the highest common video
resolution amongst them. Example: Using a 1080p source, if 3 of the displays
support a maximum resolution of 1080p and 1 displ supports a maximim ay
resolution of 720p ate at a resolution of 720p. If the 720p , all 4 display will oper
TV in the example is then turned off, the other 3 displays can then operate in
1080p resolution. Turn Off then turn On the matrix to refresh the configuration.
The three 1080p TV’s will refresh (flicker) then each will displ a 1080p picture.ay
A SSISTANCE: Questions regarding this product or its product
warranty, please check out our b site at: www.accellcables.com. We
Customer service can be reached by email at support@accellcables.com
or phone at 510-438-9288, toll free 877-353-0772 (M-F 9am-5pm PST).
1-YEAR MANUFACTURERS WARRANTY
The Accell UltraAV Matrix is warranted for one year from date of
purchase to be free of defects in material and workmanship. In the event
of such defects, the Accell product will be repaired without charge or
replaced with a new one at our option, if delivered to Accell Corporation
prepaid, together with a copy of the sales receipt indicating the proof of
purchase date and place of purchase. This warranty excludes defects due
to normal wear, abuse, shipping damage, or failure to use the product
in accordance with the instructions. ACCELL CORPORATION SHALL NOT
BE LIABLE FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF
USE OF THE PRODUCT, LOSS OF TIME, INTERRUPTED OPERATION OR
COMMERCIAL LOSS, OR ANY OTHER DAMAGES, WHETHER INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE. YOU AGREE THAT ACCELL’S MAXIMUM
LIABILITY ARISING FROM ANY PRODUCT SOLD BY ACCELL SHALL NOT
EXCEED THE PRICE OF SUCH PRODUCT. SOME JURISDICTIONS DO NOT
ALLOW THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN
DAMAGES, SO THE ABOVE MAY NOT APPLY TO YOU TO THE EXTENT
SUCH JURISDICTION’S LAW IS APPLICABLE TO THIS AGREEMENT. This
warranty gives you specific legal rights, and you may have other rights
that vary from state to state.
LIMITATION OF LIABILITY
IN NO EVENT SHALL ACCELL CORPORATION, ITS SUBSIDIARIES
OR AFFILIATES, OR THEIR RESPECTIVE PARTNERS, OFFICERS,
DIRECTORS, EMPLOYEES, SHAREHOLDERS, REPRESENTATIVES OR
AGENTS (COLLECTIVELY, “ACCELL”) BE LIABLE FOR DIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR INDIRECT DAMAGES
(INCLUDING BUT NOT LIMITED TO, LOSS OF DATA, USE OR PROFITS),
HOWEVER CAUSED, WHETHER FOR BREACH OF CONTRACT, NEGLIGENCE,
OR OTHERWISE, AND WHETHER OR NOT ACCELL HAS BEEN ADVISED
OF THE POSSIBILITY OF ANY SUCH DAMAGES. YOU AGREE THAT
ACCELL’S MAXIMUM LIABILITY ARISING FROM ANY PRODUCT SOLD
BY ACCELL SHALL NOT EXCEED THE PRICE OF SUCH PRODUCT. SOME
JURISDICTIONS DO NOT ALLOW THE LIMITATION OF EXCLUSION OF
LIABILITY FOR CERTAIN DAMAGES, SO THE ABOVE MAY NOT APPLY TO
YOU TO THE EXTENT SUCH JURISDICTION’S LAW IS APPLICABLE TO
THIS AGREEMENT.
WARRANTY RETURNS PROCEDURE
Contact Customer Support to obtain a Return Authorization (RMA)
number. RMA numbers are valid for 30 days from the date of issuance.
We are unable to accept returns without an RMA number. Returns
without an RMA number clearly printed on the outside of the package
will be refused and returned unopened. All returns must be shipped
prepaid at the expense of the shipper.
Accell assumes no responsibility for any inaccuracies and liability for
direct, indirect, special, incidental, or consequential damages as a result.
Due to ongoing improvements, Accell reserves the right to make changes
to hardware, packaging and any accompanying documentation without
prior written notice.
©2013 Accell Corporation, All Rights Reserved. Accell and UltraAV are
registered trademarks of Accell Corporation.
Support
RS-232 Control Port (4x4 HDMI Matrix)
The RS-232 port located on the 4x4 HDMI Matix provides control similiar
to the remote control from a remote device. A correctly configured
RS232 cable is required. Connect the RS232 cable end to your PC Serial
port (default =COM 1). The other end to HDMI Matrix RS232 port.
Place the included CD-ROM into your computer CD-ROM drive. Go to
the CD-ROM dri and double-click the “HDMI FamilySetupB.exe” file ve
to install the command configuration application. The HEX codes and
settings, RS-232 cable configuration as well as additional details on the
usage of the application are included in PDF file format on the CD. Open
the CD and locate the PDF file. open/read use Adobe Acrobat Reader.To
The front panel of the matrix has ports labeled . Each IR IR Channels
port can accept an IR ansmitter (I TX). Each IRTr R- -TX can send an IR
control signal to a source device. The IR-Channel ports are numbered,
corresponding to the matrix’s HDMI Output. Using the optional Ultra-IR
Adapter Kit PN: B164B-001B, the IR-Adapter would be plugged into the
display side of the HDMI cable that is plugged into HDMI Output 1. An
IR Receiver (IR-RX) would be plugged into the IR-Adapte Plug an IR-r.
TX into the IR Channel 1 port. Position the end of the IR-TX towards the
source device you want to control. For control from the other displ ay
(Output) locations, multiple IR-Adapter kits can be used. One IR-RX can
be used per display.
To control multiple source devices with one IR-TX, stack the sources
together and position the IR-TX so that all the source devices can receive
the IR signal (Blast) from the IR-TX.
The port labeled “IR Extender” accepts an optional IR ceiver, taking Re
commands from the included matrix remote control. This receiver
enables line-of-sight if the matrix with its built labeled on -in IR receiver,
the front panel as , is not visable.IR

Produktspecifikationer

Varumärke: Accell
Kategori: mottagare
Modell: UltraAV K072C-013B

Behöver du hjälp?

Om du behöver hjälp med Accell UltraAV K072C-013B ställ en fråga nedan och andra användare kommer att svara dig


mottagare Accell Manualer

Accell

Accell UltraAV K072C-013B Bruksanvisning

25 Augusti 2024

mottagare Manualer

Nyaste mottagare Manualer

Speco Technologies

Speco Technologies PBM120AT Bruksanvisning

27 Oktober 2024
Fosi Audio

Fosi Audio V3 Bruksanvisning

26 Oktober 2024
Jensen

Jensen CAR710-4BC Bruksanvisning

26 Oktober 2024
Onkyo

Onkyo TX-RZ830 Bruksanvisning

24 Oktober 2024
Pioneer

Pioneer VSX-1122K Bruksanvisning

22 Oktober 2024
NAD

NAD C 355BEE Bruksanvisning

21 Oktober 2024
Yamaha

Yamaha HTR-5072 Bruksanvisning

21 Oktober 2024
Yamaha

Yamaha RX-A810 Bruksanvisning

20 Oktober 2024
Sherwood

Sherwood R-607 Bruksanvisning

20 Oktober 2024
Denon

Denon AVC-S660H Bruksanvisning

19 Oktober 2024