Acratech Leveling Base 1117 Bruksanvisning
Läs nedan 📖 manual på svenska för Acratech Leveling Base 1117 (2 sidor) i kategorin Stativ. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/2
ACRATECH INC.
QUALITY PRECISION PRODUCTS
CAUTION: READ ALL INSTRUCTIONS BEFORE INSTALLING YOUR NEW
LEVELING BASE.
Thank you for purchasing the Acratech leveling base. Your new leveling base is
manufactured using the finest materials and workmanship. With proper care your
leveling base should last for many years.
The main adjustment knob and is used to tighten and loosen the ball so you can
adjust the leveling base. The knob is often only partially loosened so it will
maintain a controlled amount of friction or tension on the ball. The smaller knob is
preset and cannot be adjusted.
INSTALLING YOUR LEVELING BASE ON YOUR TRIPOD
1) If the threaded hole in the bottom of your new leveling base is larger in
diameter than the threaded stud on top of your tripod, then install the
brass reducer bushing provided. To do this you should use a small coin to
hand tighten the reducer bushing to moderate tightness. Measure the
length of the bolt sticking out of your tripod where you are going to install
your new Leveling Base. It should stick up at least ¼ in (6mm) and be no
longer than 3/8 in (9.5mm), if the bolt is too long it must be shortened
(Acratech can do this for a minimal charge).
2) Being careful not to cross thread, slowly tighten your new leveling base
onto your tripod “firmly hand tight”.
3) After installing your new leveling base, CAREFULLY make sure that it is
not interfering or binding on any part of your tripod. IF ANY
INTERFERING OR BINDING OCCURS, REMOVE THE LEVELING BASE
AND CONTACT ACRATECH BEFORE CONTINUING.
Leveling Base installation continued:
4) Make sure the leveling base is installed tight enough so it will not loosen
during use.
5) Use the same procedure listed above to install your tripod head onto your
leveling base.
6) When using any tripod, tripod head, or quick release system you should
always “ test the set-up” by securely grasping the camera and trying to
move it left, right, up, down, forward, back, etc. to make sure everything is
tight and secure before removing your hands from your camera. This
should be done every time you put any camera on any tripod.
7) The Acratech Leveling base is equipped with special knobs that cannot
vibrate loose and fall off. Do not try to remove knobs or loosen past the
point where resistance is felt.
8) Care for your new leveling base:
Keep your new ball head clean and free from debris.
Clean using a damp cloth, water or rubbing alcohol can be used.
DO NOT USE OIL OR WD40 ON THE BALL.
When storing you ballhead for long periods of time,
the knobs should not be rmly tightened.
Thank you for choosing an Acratech product. If your Leveling Base or other
Acratech product needs service or repair please send it directly to Acratech. Do
not return it to your dealer. If you have any questions or comments please call
us at (909) 394-1802 or E-mail us at info@acratech.net
Produktspecifikationer
| Varumärke: | Acratech |
| Kategori: | Stativ |
| Modell: | Leveling Base 1117 |
Behöver du hjälp?
Om du behöver hjälp med Acratech Leveling Base 1117 ställ en fråga nedan och andra användare kommer att svara dig
Stativ Acratech Manualer
1 September 2024
1 September 2024
Stativ Manualer
- Stativ Sony
- Stativ Nikon
- Stativ Alpine
- Stativ Silvercrest
- Stativ Pyle
- Stativ Livoo
- Stativ Asus
- Stativ Kodak
- Stativ Trust
- Stativ Carson
- Stativ Easypix
- Stativ Hama
- Stativ AVerMedia
- Stativ Celestron
- Stativ DJI
- Stativ Vello
- Stativ Rollei
- Stativ Godox
- Stativ Magnus
- Stativ Barska
- Stativ Zhiyun
- Stativ Miller
- Stativ Benro
- Stativ GVM
- Stativ Vortex
- Stativ Omnitronic
- Stativ Sachtler
- Stativ Sevenoak
- Stativ Laserliner
- Stativ Sunpak
- Stativ Celly
- Stativ Eurolite
- Stativ Drift
- Stativ Gitzo
- Stativ Proaim
- Stativ Revo
- Stativ Konig & Meyer
- Stativ Manfrotto
- Stativ Velbon
- Stativ ARRI
- Stativ Ultimate Support
- Stativ Levenhuk
- Stativ JOBY
- Stativ Oben
- Stativ Dorr
- Stativ Glide Gear
- Stativ Winegard
- Stativ Libec
- Stativ Redrock Micro
- Stativ Auray
- Stativ Kogan
- Stativ MOZA
- Stativ Flycam
- Stativ Gravity
- Stativ Sirui
- Stativ Vinten
- Stativ Neewer
- Stativ ProMediaGear
- Stativ Ravelli
- Stativ Fidlock
- Stativ Mantona
- Stativ Olloclip
- Stativ Cullmann
- Stativ Vanguard
- Stativ Bauhn
- Stativ IFootage
- Stativ SmallRig
- Stativ FeiYu-Tech
- Stativ FeiyuTech
- Stativ Sky-Watcher
- Stativ Hohem
- Stativ MOVE'N SEE
- Stativ On Air
- Stativ Kaiser Fototechnik
- Stativ Slidekamera
- Stativ IOptron
- Stativ FLOWCINE
- Stativ SteadiCam
- Stativ Fat Gecko
- Stativ 3 Legged Thing
- Stativ FLM
- Stativ Peak Design
- Stativ Easyrig
- Stativ Robus
- Stativ Studio Assets
- Stativ Square Jellyfish
- Stativ Stalco
- Stativ Tiltall
- Stativ E-Image
- Stativ Cam Caddie
- Stativ MotoCrane
- Stativ Cartoni
- Stativ HPRC
- Stativ Really Right Stuff
- Stativ Ruggard
- Stativ Ready Rig
- Stativ Axler
Nyaste Stativ Manualer
15 Januari 2025
15 Januari 2025
15 Januari 2025
15 Januari 2025
13 Januari 2025
8 Januari 2025
6 Januari 2025
5 Januari 2025
5 Januari 2025
5 Januari 2025