Aeon Labs Minimote black Bruksanvisning

Aeon Labs Fjärrkontroll Minimote black

Läs nedan 📖 manual på svenska för Aeon Labs Minimote black (7 sidor) i kategorin Fjärrkontroll. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/7

AEO_MREM_B

Aeonlabs Minimote black

Firmware Version : 1.0

Quick Start

R This device is a Z-Wave Remote Control.

Use Network Management Buttons to include and exclude devices to the remote controls network and use the LEARN button to

include the minimote into a different network. Pushing the LEARN button for 5 sec will wake up the device.

Please refer to the chapters below for detailed information about all aspects of the products usage.

Product description

The Aeon Labs mini remote control can control a variety of Z-Wave compatible devices such as switches, dimmers, window blinds

and motion sensors. The device can include and exclude devices, group them and set and release associations. The mini remote

only offers four control buttons for scene selection. Behind a slider there are four more buttons for Z-Wave network control. A non-

replaceable but rechargeable battery powers the remote control. Recharging is done on a conventional USB bus using the charging

cable provided. The product is in the color black.

Installation Guidelines

The device is ready for use. In case there are no LED signals when hitting the buttons the device needs to be recharged using the

USB cable provided.

Behavior within the Z-Wave network

I On factory default the device does not belong to any Z-Wave network. The device needs to join an existing wireless network to

communicate with the devices of this network. This process is called . Devices can also leave a network. This process isInclusion

called . Both processes are initiated by the primary controller of the Z-Wave network. This controller will be turned intoExclusion

exclusion respective inclusion mode. Please refer to your primary controllers manual on how to turn your controller into inclusion

or exclusion mode. Only if the primary controller is in inclusion or exclusion mode, this device can join or leave the network.

Leaving the network - i.e. being excluded - sets the device back to factory default.

If the device already belongs to a network, follow the exclusion process before including it in your network. Otherwise inclusion of

this device will fail. If the controller being included was a primary controller, it has to be reset first.

Once the primary controller is turned into inclusion mode . press the "Learn" button

Operating the device

The Minimote has 4 scene control buttons. A scene defines a certain switching state for a number of devices connected to this

scene. A single click on the scene button will then turn all these devices into the desired switching state. Below the cover there are

4 dedicated buttons for network management. The Minimote can manage a Z-Wave network as primary controller. However it is

also possible to reconfigure all 8 buttons for other functions e.g. activating a scene in a different controller.

Wakeup Intervals - how to communicate with the device?

W This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with

the device is limited. In order to communicate with the device, a static controller is needed in the network. This controller willC

maintain a mailbox for the battery operated devices and store commands that can not be received during deep sleep state.

Without such a controller, communication may become impossible and/or the battery life time is significantly decreased.

This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notification. The controller

can then empty the mailbox. Therefore, the device needs to be configured with the desired wakeup interval and the node ID of the

controller. If the device was included by a static controller this controller will usually perform all necessary configurations. The

wakeup interval is a tradeoff between maximal battery life time and the desired responses of the device.

The device can be woken up manually by pressing the "Learn" button for 5 seconds.

It is possible to set the node ID to 255 to send wakeup notifications as broadcast. In this mode device takes more time to go to

sleep and drains battery faster, but can notify all it's direct neighbors about a wakeup.

Node Information Frame

NIF The Node Information Frame is the business card of a Z-Wave device. It contains information about the device type and the

technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this

it may be needed for certain network operations to send out a Node Information Frame.

A single click at the "Learn" button for 5 seconds sends a Node Information Frame.

Associations

A Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called

association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive

controlling commands. These lists are called and they are always related to certain events (e.g. button association groups

pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive a

common wireless command.

Association Groups:

1 Scene 1 (max. nodes in group: 5)

2 Scene 2 (max. nodes in group: 5)

3 Scene 3 (max. nodes in group: 5)

4 Scene 4 (max. nodes in group: 5)

Set and unset associations to actuators

Associations can be assigned and remove either via Z-Wave commands or using the device itself.

Press the scene button the new device shall be associated with and keep this button pressed.1.

Issue a Node Information Frame from the target device. This is usually done by single or triple click a button. Please refer to the2.

manual of this device how to issue a NIF.

Before releasing the scene button turn the device into the desired state. After the button is released the minimote will detect3.

the status of the device and store it in the scene.

To delete a device from a scene repeat the process for the scene where the device was already associated with.

Special Functions as Z-Wave Controller

As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network

as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage

associations, and reorganize the network in case of problems. The following controller functions are supported:

Include other device in own network

CI Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is

called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion

mode the other device needs to confirm the inclusion - typically by pressing a button.

Click the "Inclusion" button to start the inclusion mode.

If inclusion of a new device fails, first exclude it from its previous network or reset it.

If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and

exclude devices.

To become primary a contoller have to be resetted and then include a device.

Exclude device from network

The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and

the network of this controller is terminated. No communication between the device and other devices still in the network can

happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the

other device needs to confirm the exclusion - typically by pressing a button.

Attention: Removing a device from the network means that it is turned back into factory default status. This process can also

exclude devices from it's previous network.

Click the "Exclusion" button to start the exclusion mode.

Attention: Removing a device from the network means that it is turned back into factory default status. This process can also

exclude devices from its previous network.

Produktspecifikationer

Varumärke:	Aeon Labs
Kategori:	Fjärrkontroll
Modell:	Minimote black

Behöver du hjälp?

Om du behöver hjälp med Aeon Labs Minimote black ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Fjärrkontroll Aeon Labs Manualer

Aeon Labs Minimote black Bruksanvisning

15 Augusti 2024

Fjärrkontroll Manualer

Nyaste Fjärrkontroll Manualer

Monacor DRM-880WP Bruksanvisning

27 Oktober 2024

Hama Spot-Pointer V2 Bruksanvisning

26 Oktober 2024

Sony RM-ED022 Bruksanvisning

21 Oktober 2024

Sonos Control Bruksanvisning

18 Oktober 2024

One For All URC 7935 Bruksanvisning

18 Oktober 2024

Canon BG-E20 Bruksanvisning

12 Oktober 2024

Neewer RT112 Bruksanvisning

8 Oktober 2024

Neewer RT113 Bruksanvisning

8 Oktober 2024

Logitech Harmony 785 Bruksanvisning

8 Oktober 2024

DSC WS4949 Bruksanvisning

8 Oktober 2024