Alcatel Office DECT Repeater Bruksanvisning

Alcatel Telefon Office DECT Repeater

Läs nedan 📖 manual på svenska för Alcatel Office DECT Repeater (1 sidor) i kategorin Telefon. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

Office DECT Repeater

LED indicator

Antenna

Power socket

1. GETTING TO KNOW YOUR REPEATER

1.1 Overview of your Repeater

Wall mount slots

SETUP button

The SETUP button is used to initiate registration/de-registration process.

The LED indicator on the repeater is used to show the link or usage status of the repeater.

Problems Solutions

There is a lot of static when

calls handover to the repeater.

and/or

The LED on the repeater

won't stop flashing.

Moving the repeater closer to the base.

Checking for interference from electronic devices.

Making sure the repeater is not too close to metal objects

or thick walls.

De-registering the repeater and registering it to the base

again.

Calls will not handover to the

repeater.

Making sure the repeater is within the base's good signal

range.

Making sure there is at least 35 feet between repeaters.

De-registering the repeater and registering it to the base

again.

I used to be able to connect to

the base, but now I cannot.

Making sure the repeater is powered on.

De-registering the repeater and registering it to the

base again.

The repeater continues to flash

on and off after registration

process had been completed.

De-registering the repeater and registering it to the base

again.

The audio quality is very poor

or noisy when receiving a call.

The signal connection is very poor. Trying to find another

location where the signal to the base is better.

Calls lost or audio becomes

poor when moving from the

base reception range the

repeater reception range.

You may be moving out of the base or repeater reception

range, or are in a blind spot. Moving towards the base or

repeater.

3 TECHNICAL SPECIFICATIONS

AC Power Adapter Ten Pao - S004LB0600030 / S004LV0600030

input 100-240VAC 50/60Hz 150mA, output 6VDC 300mA

Frequency Band 1.88 to 1.9 GHz (bandwidth = 20 MHz)

Standards Digital Enhanced Cordless Telecommunication (DECT)

4. SAFETY

In the event of an electrical hazard, the mains adapter acts as 230V power isolating device.

It should therefore, as a precaution, be installed close to the appliance and be easily accessible.

To disconnect the device from the primary power source, the mains adapter must be removed

from the 230V AC / 50 Hz socket.

If the mains adapter fails, it must be replaced by an identical model.

If not connected to the mains power, or if there is a mains power failure, telephones that use

cordless handsets will not work.

You will then be unable to make or receive calls in the event of an emergency.

This is why we recommend that you also keep a conventional telephone – one that doesn’t

require a power supply – as a backup.

! Do not use your telephone to notify a gas leak when standing in the vicinity of the leak.

It is recommended that you avoid using this device during electrical storms.

Do not attempt to open the batteries, as they contain chemical substances. In the event of

leakage, avoid contact with the skin, eyes, nose and mouth. In the event of contact, rinse the

affected part for about twenty minutes with running water and seek urgent medical attention.

Clean the product with absorbent paper or a dry cloth and contact your reseller for replacement

batteries.

ATLINKS hereby declares that the conform to the essential Office DECT Repeater

requirements and other applicable provisions of European directive 1999/5/EC.

LED

Description

Powered Off

Repeater is not registered

Repeater in registration mode

Registration is completed successfully

Good link to telephone base

Weak link to telephone base

No Link to telephone base

Repeater is in use with good link to telephone base

Repeater is in use with weak link to telephone base

Color

Red

Red/Blue

Blue

Purple

Red

Blue

Purple

Long Flash

Toggle

Triple Flash

Steady On

Double Flash

Pattern

1.2 How it works?

The DECT repeater lets you extend the coverage area of your telephone system in all

directions, including up and down. When registered to the base, the repeater’s coverage area

overlaps the coverage area of the base, the base can hand-off calls to the repeater as the user

moves from one coverage area to another. When connected to the repeater, the mobile

handset operates in the exactly same way as it does when connected to the base, and the

hand-off from the base to the repeater can be completely invisible to the end user, even during

an active call.

Each base supports up to six repeaters, so you can extend the base coverage in all directions,

including through floors and ceilings.

In addition, the DECT Repeater supports a sequential or "daisy chain" layout to extend

coverage in a single direction. Up to two repeaters can be installed in sequence.

IMPORTANT: It is possible to roam between the Repeater and the base, however, call

handover during conversation is not always guaranteed.

1.3 Setting up your Repeater

Before installing the repeater, you need to activate the repeater mode on your telephone

system and then register the repeater to the base.

1.3.1 Automatic registration

The repeater seeks out the base and automatically registers to that base.

1. Make sure the repeater is powered off (i.e., the AC power adapter is not connected).

2. Turn on the Repeater mode on the base and then set the base into registration mode.

(Consult the User Manual that comes with your base station for more information).

3. Use the AC adapter to connect the repeater to a power outlet (Do not use a power outlet

controlled by a wall switch). The repeater will register to the telephone base automatically.

Note: If the LED continues to flash in red, try registering the repeater again.

Use ONLY the power adapter that came with your repeater. A different power adapter may

cause an electrical hazard or damage the repeater.

The repeater is now registered to this base and is ready to use.

You can safely disconnect the power and move the repeater to the selected location, the

repeater will stay registered to the base.

1.3.2 Manual registration (optional)

You can also follow the instructions below to register the repeater manually.

1. Make sure the repeater is powered off (i.e., the AC power adapter is not connected).

2. Turn on the Repeater mode on the base and then set the base into registration mode.

3. Use the AC adapter to connect the repeater to a power outlet.

4. Press and hold the SETUP button for 5 seconds. The repeater will start the registration to the

base.

NOTE: The registration mode of the repeater could last for 30 minutes for your convenience.

1.3.3 De-registration / Factory default

You can also de-register and then register the repeater again when it cannot hand-off the signal

or you want to register it to another base station. Without deregistration, new registration to

another telephone base will overwrite previous base record when the registration is completed.

Follow the instructions below to de-register the repeater:

1. Disconnect the AC power of repeater.

2. Press and hold the SETUP button, then plug in DC power and hold for 5 seconds.

3. The repeater will be de-registered (reset to factory default).

1.4 Installing the Repeater

You need to activate the repeater mode on the base before installing the repeater, and then

1.4.1 Location

To get the optimum conditions, the repeater should be placed in a proper location. You can

locate the repeater through the LED indicator’s behaviors.

To get the best operating conditions for the repeater, it is important to place it correctly. Here are

a few tips for placing repeaters:

Place the repeater as high as possible, but at least 6 feet off the ground.

Make sure you have good reception from the base.

Make sure the location is close to a corresponding power outlet. Never install electrical cords

across a traffic area: they can create a trip hazard or become damaged and create a fire or

electrical hazard.

Allow at least 35 feet between repeaters (if you are installing repeaters across multiple floors,

remember to allow 35 feet vertically as well).

Avoid sources of electrical interference, such as hi-fi systems, office equipment or microwave

ovens.

Avoid heat sources and direct sunlight.

Avoid things that can interfere with radio signals, such as metal doors, thick walls, niches

and cupboards.

1.4.2 Map the Base coverage area

To find the best location for the repeater, you need to determine the base coverage area.

Stand near the base and make a call. Walk away from the base with the handset, and make a

note where the signal becomes weaker. The optimum location for the repeater is as far from the

base as possible while still maintaining a "good" signal, or just inside the location where the

signal became weaker.

1.4.3 Test the location

To test the location, plug the AC adapter into the repeater, then hold the repeater in the place

where you plan to mount it. The LED should remain on and steady, indicating that the repeater

has a good signal from the base.

1.4.4 Installing the Repeater

1. Hold the repeater in its final location, and mark the center of the top edge.

2. From the edge mark, measure down approximately 1-1/2 inches, and mark the upper screw

location, then move down approximately 2-1/2 inches to mark the lower screw location.

3. At the screw locations, use a 3/16ths drill bit to make two pilot holes approximately one inch

deep.

4. Place the wall anchor into the pilot holes and tap it gently with a hammer until the anchor is

flush with the wall.

5. Insert the mounting screws into the anchor, leaving approximately 1/4 inch space between

the screw head and the wall.

6. Put the wall mount slot on the back of the repeater over the screw heads and slide the

repeater down into place.

IMPORTANT: Be sure the wall material can hold the weight of the repeater. Never install a

repeater in damaged or decaying wall material.

7. Connect the repeater to the corresponding power outlet.

2. TROUBLESHOOTING

5. ENVIRONMENT

This symbol means that your inoperative electronic appliance must be collected

separately and not mixed with the household waste. The European Union has

implemented a specific collection and recycling system for which producers are

responsible.

This appliance has been designed and manufactured with high quality materials and components

that can be recycled and reused. Electrical and electronic appliances are liable to contain parts

that are necessary in order for the system to work properly but which can become a health and

environmental hazard if they are not handled or disposed of in the proper way.

Consequently, please do not throw out your inoperative appliance with the household waste.

If you are the owner of the appliance, you must deposit it at the appropriate local collection

point or leave it with the vendor when buying a new appliance.

- If you are a professional user, please follow your supplier's instructions.

- If the appliance is rented to you or left in your care, please contact your service provider.

Keen to preserve the environment, ATLINKS has equipped this appliance with a switching

power supply, offering better energy efficiency. The advantages include not only very low

electricity consumption, but also a more compact format than the conventional power supply

units used by the previous range.

The used batteries from your telephone (if it has batteries) must be disposed of in compliance

with current environmental protection regulations. Comply with your local regulations. Return

your batteries to your reseller or dispose of them at an approved recycling centre.

Help us protect the environment in which we live!

Model Office DECT Repeater

A/W No.:10000361 Rev.0 (EN)

Printed in China

The Manufacturer reserves the right to modif roducts in order to make y the speciﬁcations of its p

technical improvements or comply with new regulations.

ALCATEL and ATLINKS are registered trademarks.

The Alcatel logo and Alcatel name are trademarks of Alcatel and used under licence by

ATLINKS.

ATLINKS Europe 22, quai Gallieni – 92150 Suresnes – France

www.atlinks.com

Office DECT Repeater Quick Guide_trim size: 420mm (H) x 297mm (W) (EN)

Produktspecifikationer

Varumärke:	Alcatel
Kategori:	Telefon
Modell:	Office DECT Repeater

Behöver du hjälp?

Om du behöver hjälp med Alcatel Office DECT Repeater ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Telefon Alcatel Manualer

Alcatel T MAX 10 Bruksanvisning

20 Februari 2025

Alcatel Versatis 80 Bruksanvisning

8 Januari 2025

Alcatel XL650 Combo Voice Bruksanvisning

30 December 2025

Alcatel Smile Bruksanvisning

18 Oktober 2024

Alcatel Temporis 500 Bruksanvisning

29 September 2024

Alcatel Temporis 700 pro Bruksanvisning

29 September 2024

Alcatel Temporis 23 Bruksanvisning

27 September 2024

Alcatel F630 Bruksanvisning

26 September 2024

Alcatel F670 Bruksanvisning

26 September 2024

Alcatel E230 Bruksanvisning

26 September 2024

Telefon Manualer

Nyaste Telefon Manualer

Panasonic KX-TGC202 Bruksanvisning

3 April 2025

VTech Trimstyle CD1113 Bruksanvisning

2 April 2025

HMD 150 Music Bruksanvisning

30 Mars 2025

Vimar R289 Bruksanvisning

29 Mars 2025

Trevi FLEX 51 Bruksanvisning

18 Mars 2025

Realme C25Y Bruksanvisning

5 Mars 2025

Realme XT Bruksanvisning

5 Mars 2025

Realme GT 5G Bruksanvisning

5 Mars 2025

Realme GT Neo2T Bruksanvisning

5 Mars 2025

Ooma Telo LTE Bruksanvisning

5 Mars 2025