Allied Telesis AT-STACKXG-00 Bruksanvisning

Allied Telesis Inte kategoriserad AT-STACKXG-00

Läs nedan 📖 manual på svenska för Allied Telesis AT-STACKXG-00 (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

Overview

The AT-StackXG Stacking Module allows the formation of a stacked

configuration when installed in each switch in a group of AT-9400 Basic Layer

3 Gigabit Ethernet Series switches or x600 Layer 3 Gigabit Ethernet Series

switches. With its two full-duplex, 12-Gbps stacking ports, the module unifies

the individual switches of the stack into a single, logical unit so that the

network operations of the devices, such as spanning tree, port mirroring and

port trunking, encompass all of the Gigabit Ethernet ports. This can simplify

network management and augment network bandwidth.

Figure 1. AT-StackXG Stacking Module

1240

-LX44CPUCVR

AT-StackXG

Stack Port 1

Stack Port 2

Preparation

Review the following information before installing the AT-StackXG Stacking

Module:

Caution

The AT-StackXG Stacking Module is sensitive to and can be damaged

by electrostatic discharge. Wear a grounding device and observe

electrostatic discharge precautions when installing the module in the

chassis.

❑The AT-StackXG Stacking Module is hardware hot-swappable. You can

install or replace the module while the switch is powered on.

Caution

If the stacking module is added or replaced in an operating stack, the

stack topology may change and cause the stack to reboot and interrupt

network traffic.

AT-9400 Basic Layer 3 Gigabit Ethernet Switch Series :

❑Do not install the module until you have read the latest version of the

AT-S63 Software Release Notes and the AT-9400 Series Stack Installation

Guide.

❑The AT-StackXG Stacking Module is supported in the AT-9424Ts,

AT-9424Ts/XP, and AT-9448Ts/XP Basic Layer 3 Switches. All other

models in the AT-9400 Series do not support the HiGig stacking feature and

must be used as stand-alone switches.

❑Support for the AT-StackXG Stacking Module requires Version 3.0.0 or

later of the AT-S63 Management Software.

x600 Layer 3 Switch Gigabit Ethernet Switch Series:

❑The AT-StackXG Stacking Module is supported in all x600 series products.

❑Do not install the module until you have read the latest version of the AW+

Software Release Notes and the x600 Series product documentation.

❑Support for the AT-StackXG Stacking Module requires software version

5.3.1 or later of AlliedWare Plus.

Package Contents

The following items are included in the shipping package. If an item is missing

or damaged, contact your Allied Telesis sales representative for assistance.

❑One AT-StackXG Stacking Module

❑One AT-StackXG Stacking Cable (length - .5 m)

❑Installation Guide

Warranty Information

The AT-StackXG Stacking Module has a Lifetime Warranty. Go to

www.alliedtelesis.com/warranty for the specific terms and conditions

of the warranty and for warranty registration.

Installing the AT-StackXG Stacking Module

To install the AT-StackXG Stacking Module, perform the following procedure:

1. Remove the module from the shipping package.

Note

Store the packaging material in a safe location. You must use the original

shipping material if you need to return the unit to Allied Telesis.

2. Remove the blank panel from the expansion slot on the back panel of the

switch by loosening the two captive screws on the panel with a cross-head

screwdriver.

Figure 2. Removing the Blank Panel from the Expansion Slot

Note

Do not remove the blank panel from the chassis until you are ready to

install a module. An open slot allows dust to enter the unit and reduces

proper airflow and cooling.

3. Align the edges of the module with the guides in the slot and carefully slide

the module into the chassis until it is flush with the back panel of the

chassis, as shown in Figure 3. Light pressure may be needed to seat the

module on the connector on the back panel of the chassis.

Caution

Do not force the module into place. Doing so may damage the

connector pins on the backplane inside the chassis. If there is

resistance, remove the module and reinsert it after verifying that the

edges of the card are properly aligned in the guides in the chassis’

module slot.

1241

AT-LX44CPUCV

AT-StackXG Stacking Module

Installation Guide

Allied Telesis, Inc.

www.alliedtelesis.com

613-001122 Rev A 1

*613-001122 RevA*

2 3

Figure 3. Installing the AT-StackXG Stacking Module

4. Secure the module to the chassis by tightening the two captive screws with

a cross-head screwdriver.

Figure 4. Securing the AT-StackXG Stacking Module

Note

The remaining steps attach the stacking cable to the stacking module. If

you are installing the stacking module in an AT-9400 Series Switch, do

not cable the module until you have prepared the switch’s AT-S63

Management Software, as explained in the AT-9400 Series Stack

Installation Guide.

Note

If you are installing the stacking module in an x600 Series Switch, do not

cable the module until you have prepared the switch’s AlliedWare Plus

Software on the x600 Series Switches as explained in the x600 series

AlliedWare Plus 5.3.1 Software Reference.

1242

AT-LX44CPUCV R

AT-Sta ckXG

St ack Po

rt 1 St ack Po

1243

-LX44CPUCVR

AT-StackXG

Stack Por

t 1 Sta

ck Port 2

5. Remove the plastic protector from the connector at one end of the stacking

cable.

Figure 5. Removing the Plastic Protector

6. Connect the cable to either Stack Port 1 or Stack Port 2 on the stacking

module and secure by tightening the two captive thumbscrews.

7. Remove the plastic protector from the connector at the other end of the

stacking cable and connect it to a Stack Port on the stacking module in the

next switch of the stack. A stacking cable must crossover and connect to

a different port on the next stacking module. Stack Port 1 on a module

must connect to Stack Port 2 on the next module. Do not connect two

Stack Port 1 ports or Stack Port 2 ports together.

AT-StackXG Stacking Module LEDs

The LEDs in the group labelled Stack on the front panel of the switch display

the status of the AT-StackXG Stacking Module and the stacking ports. The

states of the LEDs are defined in this table.

LED State Description

MSTR

Off The switch is not the master unit of the stack or

is not a member of a stack.

Green The switch is the master unit of the stack.

1 and 2 L/A

Off The stacking port has not established a link to

another AT-StackXG Stacking Module.

Steady

green

The stacking port has established a link to a

stacking port on another AT-StackXG Stacking

Module.

Flashing

green

The stacking port is sending or receiving packet

traffic.

PRES

Off The expansion slot on the switch is empty.

Green The AT-StackXG Stacking Module is installed

in the expansion slot.

1244

Technical Specifications

Dimensions (H x W x D) 3.1 x 14.7 x 8.6 cm

(1.2 x 5.8 x 3.4 in.)

Weight 131 g (0.35 lb.)

Operating Temperature: 0° C to 40° C

(32° F to 104° F)

Storage Temperature: -25° C to 70° C

(-° 13F to 158° F)

Operating Humidity: 5% to 90% noncondensing

Storage Humidity: 5% to 95% noncondensing

Maximum Operating Altitude: 3,048 m (10,000 ft)

Maximum Nonoperating

Altitude: 4,000 m (13,000 ft)

Electrical Safety and Emission Statement

Standards: This product meets the following standards when installed in compliant host equipment.

RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-3-3, VCCI Class A, C-TICK,

WARNING: In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

EMC (Immunity)EN55024

Electrical Safety EN60950-1 (TUV), UL 60950-1 ( CULUS)

Allied Telesis is a registered trademark of Allied Telesis, Incorporated. All other product names,

company names, logos or other designations mentioned herein are trademarks or registered trademarks

of their respective owners.

No part of this publication may be reproduced without prior written permission from Allied Telesis,

Inc.

U.S. Federal Communications Commission

Radiated Energy

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant

to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with this instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the interference at

his own expense.

Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right

to operate this equipment.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

European Union Restrictions of the Use of Certain Hazardous Substances

(RoHS) in Electrical and Electronic Equipment

This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of the Use of Certain

Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Allied Telesis ensures RoHS

conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining

Manufacturing process controls.

456

Produktspecifikationer

Varumärke:	Allied Telesis
Kategori:	Inte kategoriserad
Modell:	AT-STACKXG-00

Behöver du hjälp?

Om du behöver hjälp med Allied Telesis AT-STACKXG-00 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Allied Telesis Manualer

Allied Telesis MMCR18 Bruksanvisning

19 September 2024

Allied Telesis AT-STACKXG-00 Bruksanvisning

19 September 2024

Allied Telesis AT-UWC-INSTALL Bruksanvisning

19 September 2024

Allied Telesis AT-XEM-12TV2 Bruksanvisning

19 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024