AMX VPX-1701 Bruksanvisning

AMX Inte kategoriserad VPX-1701

Läs nedan 📖 manual på svenska för AMX VPX-1701 (51 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/51
User Manual – VPX-1701
5
Logo ............................................................................................................. 30
Network ........................................................................................................ 31
System.......................................................................................................... 32
Firmware Upgrade ........................................................................................................ 32
Before Starting ...................................................................................................... 32
Transferring KIT Files............................................................................................. 32
Troubleshooting ........................................................................................................... 34
API Command Set .......................................................................................................... 35
NetLinx Commands ................................................................................................ 35
Telnet/SSH Commands ........................................................................................... 43
User Manual – VPX-1701
6
Overview
The VPX-1701 is an advanced presentation switcher, allowing switching among seven inputs and distribution to two
outputs. It offers two VGA inputs with balanced analog audio embedded, five HDMI inputs, one HDMI output to a local
display, plus one balanced de-embedded analog audio output and one HDBaseT mirrored output to a remote display
via a Cat X cable.
The VPX- -1701 has one built in scaler which supports up to 4K@60Hz 4:4:4 8bit
.
The video stream goes through the
scaler first before distributing to two outputs. The scaler output can be set to fixed resolution or auto scaling. When set to
auto scaling, the scaler analyzes the EDIDs of two connected displays and output optimum resolution for both displays.
The VPX-1701 can be set to auto switching or manual switching. It can be controlled by front panel buttons, LAN control
with NetLinx Studio, Telnet API and Web GUI.
Powered by HDBT 2.0 and DSC (Display Stream Compression), the VPX 1701 can transmit 4K@60Hz 4:4:4 8bit video up -
to 80m/262 ft via a shielded Cat 6a/7 cable, along with USB 2.0 (Host), bidirectional RS232 and IR pass through. HDBaseT -
output also features PoE (PSE) to power an HDBT receiver.
The VPX-1701 simplifies integration and installation of a small presentation system for classrooms and small offices,
providing localized presentation switching support over long distances.
Features
•
Provides two VGA inputs with balanced embedded audio, five HDMI inputs, one HDMI and HDBT mirrored outputs.
•
HDMI inputs, HDMI and HDBT outputs support up to 4K@60Hz 4:4:4 8bit and HDCP 2.2; VGA input supports up to 1920 x
1200@60Hz.
•
Built-in scaler supports up to 4K@60Hz 4:4:4 8bit.
•
Supports one- way PoE to power the remote HDBT receiver.
•
HDBT transmits 4K@60 4:4:4 signals up to 80m/262 ft, 1080P signal up to 100m/328ft via a shielded Cat 6a/7cable.
•
Transmits USB 2.0, bi-directional RS232 and IR signal over HDBT.
•
Balanced de embedded analog audio output with volume control.-
•
Auto-switching to the latest connected source input by detecting input signal status.
•
Fast switching.
•
Able to turn on/off connected displays automatically by detecting input signal status with its built- in CEC controller.
•
Selection buttons on the front panel for local control and contact closures for remote keypad control.
•
Supports LAN control through NetLinx Studio, Telnet API and WEB UI.
Package Contents
•
1 x VPX- 1701
•
1 x US AC Power Cord
•
1 x UK AC Power Cord
•
1 x EU AC Power Cord
•
7 x Phoenix Male Connector (3.5mm, 5 Pins)
•
1 x Phoenix Male Connector (3.5mm, 6 Pins)
•
2 x Mounting Bracket (with Screws)
User Manual – VPX-1701
15
Pinout Information
The following figures show the pinouts of the phoenix connectors.
RS232&IR
Connects to the RS232 and IR devices -with the 6 pole, 3.5mm captive screw connectors.
Audio IN/OUT
Connect to audio device with the 3 pole, 3.5mm captive screw connector- .
User Manual – VPX-1701
16
Installation and Wiring
Warning:
Before installation, ensure the device is disconnected from the power source. The VPX- 1701 can be placed on a
solid and stable surface or installed in a standard equipment rack.
Installation
1. Attach the installation bracket to the enclosure using the screws provided.
2. The bracket is attached to the enclosure as shown.
3. Repeat steps 1-2 for the other of the side unit.
4. Attach a the brackets to surface or suitable location with user supplied screws.
Wiring
Warning:
•
Before wiring, disconnect the power from all devices.
•
Connect and disconnect the cables with care.
1. Connect the video source
Connect the VGA and HDMI sources (such as PC, Blu-ray player, Apple TV, 4K media player, etc) to the VGA IN and HDMI IN
ports of the VPX- 1701.
2.
C onnect HDMI OUT
Connect an HDMI display device (such as TV, projector, LED/LCD display) to the HDMI OUT of the VPX- 1701.
3.
Connect AUDIO OUT
Connect an audio receiver (e.g. an amplifier) to the AUDIO OUT of the VPX-1701.
4.
Connect HDBT OUT
Connect HDBT OUT of VPX- 1701 to HDBT IN of an HDBT receiver with a Cat 5e/6/6a/7 cable.
5.
Connections
for additional control options:
•
LAN control (NetLinx/Telnet/Web UI): Connect a Local Area Network to the LAN port of the VPX- 1701.
•
Input source switching control: Connect a keypad and LEDs to CONTACT IN and TALLY OUT ports for input switching and tally
indication.
•
USB control: Connect a USB host to the VPX-1701, and USB devices to the HDBT receiver for remote KVM control.
•
RS232 pass-through: Connect an RS232 device) to the RS232 port of the VPXserver ient device (or cl -1701, and an RS232 client
device (or server through. -device) to the RS232 port of the remote receiver for bidirectional RS232 pass
•
IR pass- X-through: Connect an IR emitter (or IR receiver) to the IR connector of the VP 1701, and an IR receiver (or IR emitter) to
the IR connector of the HDBT receiver for bi directional IR pass- -through.
6.
Connect
the AC power cord provided to the -VPX 1701.
One- H way Po enables the VPX-1701 to power the remote HDBT DSC receiver along a sin e Cat X cable. No additional power gl
adapter is required at the receiver.
7.
Power
on all attacheddevices.
When all connections are made and power is ON, check if all LED indicators on the VPX-1701 are normal to ensure
installation is successful. For LED indication, please refer to Panel Description section.
User Manual – VPX-1701
18
OSD
The VPX-1701 supports OSD (On Screen Display) to display its IP address. Follow these steps to initiate OSD:
1. Press and Hold the front panel buttons VGA IN 1 and VGA IN 2 for at least 3 seconds.
2. T he IP address of the VPX- 1701 will display on the upper right of the connected display’s screen for about 15s and
then disappear.
User Manual – VPX-1701
19
Input Source Switching
The VPX-1701 supports Auto and Manual Switching among the VGA and HDMI inputs.
Auto Switching
1. When multiple sources are inserted, and power is ON for all devices, the input will be switched to the active source with
the highest priority.
2. Priority: VGA IN 1 > VGA IN 2 > HDMI IN 3 > HDMI IN 4 > HDMI IN 5 > HDMI IN 6 > HDMI IN 7
3. When a new source is inserted, the input will be switched to it automatically, following the Last- - - In First Out rule.
4.
When the currently selected source is removed, the input will first be switched to the most recently selected port. If the
port has no active source, the input will be switched to the active source with the highest priority.
Note:
•
When in Auto Switching, Input Select buttons do not function. To use input select buttons, disable Auto Switching.
•
The Auto Switching function is enabled by default once all devices are powered on.
•
You can enable or disenable Auto Switching through command setting or WEB UI on NetLinx.
Manual Switching
If you want to select a specific input port using selection buttons:
1. Disable Auto Switching through command setting or WEB UI on NetLinx.
2. P ress the appropriate Input Button to select a desired input port. When an inactive port is selected, the VPX- 1701 will
output no signal.
User Manual – VPX-1701
22
NetLinx Control
Controlling the VPX-1701 through NetLinx Studio.
Before launching NetLinx Studio, connect the VPX- - 1701, PC, and control system (e.g. NX 3200) to the same network.
Note:
IDs and IP addresses in the following illustrations are examples. Check the Online Tree in NetLinx Studio to find the
correct . addresses for your device
Device Number and Ports
Each VPX-1701 has its own Device Number (which is assigned when the unit is bound to a Control System) and the following
ports.
Port 1: VGA IN 1 (AUDIO IN 1); HDMI OUT; AUDIO OUT; HDBT OUT
Port 2: VGA IN 2 (AUDIO IN 2)
Port 3: HDMI IN 3
Port 4: HDMI IN 4
Port 5: HDMI IN 5
Port 6: HDMI IN 6
Port 7: HDMI IN 7
Port 8:
Port 9: RS- 232
Port 10: HOST
Port 11: IR
Port 12:
Port 22: CONTACT IN
Port 23: TALLY OUT
In NetLinx Studio’s Online Tree, the -VPX 1701 module displays its ports.
User Manual – VPX-1701
23
Send command to control a device
Click “Diagnostics” on the menu bar, select “Control a Device”.
A window will display as follows, type the Device number, Port number, System and command respectively, and click “
Send To
Device
”. (For API commands, see the Section
API Command Set
.)
Telnet Control
Launch Telnet Window
To launch Telnet Window,
1.
Right click the Device Number in NetLinx Studio’s Online Tree, select “TELNET Window” – “Launch TELENT Window via NetLinx
Studio” (or “Launch TELENT Window via User Defined Program”)*.
User Manual – VPX-1701
24
The Telnet window opens.
2. At the prompt (>), type the Telnet command and press Enter.
* Selecting “Launch TELENT Window via User Defined Program”, may require enabling Telnet by completing the following:
(1)
go to Start/Control Panel/Programs and Features;
(2)
on the left, select “Turn Windows features on or off”;
(3)
select the - check boxes Telnet Client and Telnet Server, and click OK.
User Manual – VPX-1701
25
Web UI Control via NetLinx
To configure and control the device on the Web, right click the Device Number in the Online Tree Tab, choose “Web
Control Page” – “Launch Web Control Page via NetLinx Studio”.
User Manual – VPX-1701
27
A successful reset will restore all the device settings to their factory defaults and the device will reboot automatically. Allow at least 2
minutes oot for the reb to complete.
: Reboot button, click to reboot the device.
Steps to reboot the device:
1. Click “Reboot” button.
2. Click “OK” to proceed. Then the device will reboot immediately.
: Update status button,
click to view the device’s firmware upgrade status.
: Logout button, click to
logout from the Web UI.
:
Displays the device’s firmware version information.
Navigation Bar
The navigation
bar
includes the following tabs:
Auto Switch, Key Lock, HDCP, EDID, Display, Relay, Audio, Resolution, Logo,
Network . and System
Auto Switch
Auto Switch allows switching among multiple inputs without using the buttons on the front panel.
•
ON: Click to enable Auto Switch (default setting).
•
OFF: Click to disable Auto Switch.
User Manual – VPX-1701
28
Key Lock
Key Lock allows locking of the buttons on the VPX-1 701 to prevent accidental or unwanted switching.
•
ON: Click to enable Key Lock.
•
OFF: Click to disable Key Lock (default setting).
HDCP
HDCP Support allows enabling or disabling HDCP compatibility of each input . and HDMI output
•
ON:
Click to enable HDCP compatibility for the corresponding input, which will transmit HDCP protected content (default setting).
•
OFF:
Click to disable HDCP compatibility for the corresponding input, which will transmit non HDCP- protected content.
For HDMI Out:
•
FOLLOW:
Select to follow the output display transmit content with the same ’s HDCP compatibility for the HDMI Out, which will
HDCP compatibility as that of output displaythe (default setting).
•
HDCP 2.2:
Select oto transmit HDCP 2.2 protected content to the utput display.
•
HDCP 1.4:
Select to transmit HDCP 1.4 protected content
to the output display.
•
NO HDCP:
Select -to transmit non HDCP protected content
to the output display. (Note: If “NO HDCP” is selected for HDMI
OUT, when the HDCP protected signal is being input, the receiver will output no signal.)
•
Apply:
Click to make the selection to take effect.
EDID
EDID Support allows configuration of the EDID setting of each input.
Locate the target input port and select specific EDID nu, then click “Apply” to perform the settings from the -drop down me
setting. The default EDID settings for all HDMI input ports are “Copy EDID from output display”.
User Manual – VPX-1701
29
Display
Auto Display Control allows control of CEC- - enabled displays connected to theVPX 1701 through HDMI.
• ON:
Click to enable the Auto Display Control.
• OFF:
Click to disable the Auto Display Control. (Default setting)
• DELAY TIME (1~30 min):
Click the down arrow to set the time for the display to power off automatically when no signal is
present. Example: With the time set to 2 minutes, the output display will be powered off automatically when there is no signal
input for 2 minutes.
Note: The time range for Auto Display Control is 1 30 minutes.-
Audio
•
Output Volume: Move the slider to set the output audio volume.
• Min/Max:
Move the sliders at the left and right sides of the scale to set the minimum and maximum range of the audio volume.
•
Mute: Check (or uncheck) to mute (or unmute) the audio.
User Manual – VPX-1701
30
Resolution
• AUTO:
Click to set the output resolution to Auto mode (default setting). The output resolution may vary based on the connected
display’s native resolution.
• MANUAL:
Click to set the output resolution to Manual mode. In Manual mode, click the down arrow to select a specific output
resolution as required.
• APPLY:
Click to set the output resolution to the desired setting.
Logo
Logo section allows display content configuration for the display screen when there’s no signal output to the display.
•
BLACK
COLOR
/LOGO:
1)
BLACK:
Select to set the display screen as black when there’s no signal output to the display.
2)
LOGO:
Select to
set the display
to show a logo picture when there’s no signal output to the display.
•
L OGO TRANSITION:
1)
FIX IN CENTER:
Select to set the logo picture to be shown ’s in the display screen center when there’s no signal output to
the display. (Default setting)
2)
DRAG TOP LEFT:
Select to set the logo picture to shuttle slowly between the center and the top left of the display screen
when there’s no signal output to the display.
3)
DRAG TOP RIGHT:
Select to set the l ogo picture to shuttle slowly between the center and the top right of the display
screen when there’s no signal output to the display.
4)
DRAG BOTTOM LEFT:
Select to set the logo picture to shuttle slowly between the center and the bottom left of the
display screen when there’s no signal output to the display.
5)
DRAG BOTTOM RIGHT:
Select to set the l ogo picture to shuttle slowly between the center and the bottom right of the
display screen when there’s no signal output to the display.
•
Logo Setup
1)
CHOOSE FILE: Click to upload a logo file to the switcher from your local computer.
2)
SAVE: Click to perform the logo file uploading.
Note:
• The logo file should be in .png format with size not larger than 1280x720, 60KB.
• When the logo is loaded to the device successfully, the device will reboot immediately.
User Manual – VPX-1701
32
S ystem
The configure arameter, ogin upload system section is used to the ICSP P l password, Telnet/SSH account and certificate.
1. ICSP PARAMETER:
•
CONNECTION MODE: includes four options: NDP, Auto IP, URL/TCP, URL/UDP. The default setting is NDP.
•
CONTROLLER URL: Input the connected controller’s URL.
• SYSTEM NUMBER
: Use the Online Tree to determine the system number. By default, it is disabled to be configured.
• DEVICE NUMBER
: Use the Online Tree to determine it. By default, it is disabled to be configured.
2.
LOGIN PASSWORD:
LOGIN PASSWORD: Login Password can be changed. The default Login Password is admin.
3. TELNET/SSH ACCESS
TELNET/SSH ACCESS is used to enable or disable Telnet/SSH capability. The default setting is
ON
.
Note
: Reboot the device for the setting change to take effect.
4. TELNET/SSH ACCOUNT
TELNET/SSH ACCOUNT is used to configure the user name and password of the account.
• TELNET ACCOUNT
The default user name and password are null.
• SSH ACCOUNT
The default user name is admin, the default password is password. Note: Reboot the device for the SSH ACCOUNT setting
change to take effect.
• APPLY:
Click to choose each of the settings.
5. Upload Certificate
• Password:
Enter the password of the certificate
uploaded.
• Private Key (.pem):
Click “CHOOSE FILE” to browse for the private key in .pem format of the https certificate in your local
computer.
• Certificate (.pem):
Click
“C HOOSE FILE” to browse for the https certificate in .pem format in your local computer.
User Manual – VPX-1701
33
• Upload:
Click to upload the https certificate and its private key to the device.
Note:
When certificate upload is completed, the cer ficate module will reboot automaticti ally.
User Manual – VPX-1701
32
Firmware Upgrade
The 1701 -VPX uses KIT files for firmware upgrade.
Before Starting
1. Verify that you have the latest version of NetLinx Studio on your PC.
2. Download the latest firmware (KIT) file to your PC. (Place KIT files on a local drive for the fastest throughput.)
3.
Verify the following:
a) Verify that an Ethernet/RJ 45 cable is connected from the to the same network as the control system.- -VPX 1701
b) Verify the -VPX 1701 unit is powered ON.
4. Launch NetLinx Studio and open the Online Tree.
5. Bind the device to the integrated : select and rightController -click the -VPX 1701; from the context sensitive menu, select Network
Bind/Unbind Device (be sure the check box is selected); click OK.
Transferring KIT Files
1.
In NetLinx Studio, choose Tools > Firmware Transfers > Send to NetLinx Device to open the “Send to NetLinx Studio” dialog.
2. Click to navigate to the target directory. The selected directory path is displayed in the Location text box. KIT files
in the target directory display under File Name.
3. Select the appropriate KIT file from the File Name list.
4.
Check the number of the Device to be upgraded in the Device text box.
User Manual – VPX-1701
34
Troubleshooting
1.
Power: Ensure all devices are powered on.
2.
Indicator:
Ensure all LED indicators of the switcher are normal a ccording to the user manual.
3.
Devices:
Ensure picture can be shown normally when directly connecting a source a display device.
4.
Cable:
Plug the HDMI/Cat X cable in and out or connect a different HDMI/Cat X cable. Ensure the specific cable length is within
the available transmission range according to the Specifications Section.
5.
Compatibility:
Test other source and display devices to determine correct compatibility.

Produktspecifikationer

Varumärke: AMX
Kategori: Inte kategoriserad
Modell: VPX-1701

Behöver du hjälp?

Om du behöver hjälp med AMX VPX-1701 ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad AMX Manualer

AMX

AMX HPX-900-NA Bruksanvisning

2 Januari 2025
AMX

AMX HPG-10 Bruksanvisning

2 Januari 2025
AMX

AMX HPX-600-NA Bruksanvisning

2 Januari 2025
AMX

AMX HPX-1200-NA Bruksanvisning

2 Januari 2025
AMX

AMX HPX-900 Bruksanvisning

2 Januari 2025
AMX

AMX HydraPort HPX-1600 Bruksanvisning

27 December 2024
AMX

AMX HPG-20 Bruksanvisning

7 December 2024
AMX

AMX HPX-MSP-7-SL Bruksanvisning

25 September 2024
AMX

AMX HPX-MSP-10-SL Bruksanvisning

25 September 2024
AMX

AMX TPC-WIN8-TAB Bruksanvisning

24 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

IFM

IFM PE2599 Bruksanvisning

2 April 2025
IFM

IFM RU6035 Bruksanvisning

2 April 2025
Nedis

Nedis WCPD18W100BK Bruksanvisning

2 April 2025
Targus

Targus APK032US Bruksanvisning

2 April 2025
Beghelli

Beghelli Formula 65 LED HT Bruksanvisning

2 April 2025
Simrad

Simrad NEP-3 Bruksanvisning

2 April 2025
Simrad

Simrad S3100H Bruksanvisning

2 April 2025
Sharp

Sharp NQ-R256A Bruksanvisning

2 April 2025
Electro Harmonix

Electro Harmonix Triangle Big Muff Pi Bruksanvisning

2 April 2025
Black Box

Black Box KVS4-2002V Bruksanvisning

2 April 2025