Andrews ET 25 Bruksanvisning

Andrews Luftkonditionering ET 25

Läs nedan 📖 manual på svenska för Andrews ET 25 (3 sidor) i kategorin Luftkonditionering. Denna guide var användbar för 11 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/3

Click www.andrews-sykes.com

or Call Us Free 0800 211 611

ET 21 & 25

Portable Air Conditioning

Operating Instructions

& Safety Guide

General Safety

Keep children and animals away from air conditioning units. Never

leave them alone in a room where the units in use.

This equipment should only be used by a competent person who

has read and understood these instructions.

Never operate this equipment if you are ill, feeling tired or under the

inﬂuence of alcohol or drugs.

Keep the Air Conditioning vents clear of all obstructions.

Never put anything on top of the unit or block the air outlets.

Make sure equipment is switched off and unplugged after use.

Never leave switched on or unattended.

Do not use the unit where sunlight is shining directly onto it.

Check condition of equipment before use. If unit is showing signs

of damage contact your supplier immediately.

Use a 230V. 50HZ. 1 phase power supply only. (Wrong supply may cause a

ﬁre and / or shock hazard.)

Securely plug into an earthed supply. (Unless earthed, may cause electric shock)

Do not use a damaged power cable, plug or socket. (Short, ﬁre or shock hazard)

Do not remove plug by pulling cable or with wet hands. (Risk of ﬁre and

electric shock)

Before cleaning, remove plug from socket. (Otherwise risk of electric shock)

Do not place anything on top of the machine. (This may cause electric shock,

malfunction or injury)

Do not use an extension lead unless of the approved type. Fully uncoil extension

leads when being used. (Heavy duty, risk of ﬁre and / or electric shock.)

Ensure mains plug is clean and securely plugged in. (Otherwise it may short

causing smoke and ﬁre)

Ensure correct 13 amp fuse is ﬁtted in the plug. (Otherwise malfunction or ﬁre

may result)

Do not ‘kink’ or sharply bend the power cable nor put weight on it. (The

installation may be damaged causing ﬁre and / or electric shock)

Do not turn off by removing power plug. Always turn off at control panel ﬁrst.

(Risk of electric shock and / or malfunction)

Do not use this cooler on unstable or inclined surfaces. Always use on solid ﬂat

ﬂoor. (Risk of falling causing injury, ﬁre or malfunction)

• Ensure the safety of the location in which cooler is to be used.

• Ensure the oor or ground is smooth and sound.

• Ensure you allow at least 50cm air space all around the cooler.

• When in position LOCK the casters to prevent rolling.

• Never use the cooler at more than 2º incline.

Do not place cooler on uneven, unstable or inclined surface. (This could cause

malfunction)

When storing the cooler, ensure that it is kept in a dry, cool place. (To prevent

corrosion and malfunction)

If not being used for some time or lighting is present, always unplug from

mains. (To prevent risk of electric shock, short circuit or ﬁre)

Do not spray water on to the cooler nor use solvents such as benzene, thinner

or alcohol for cleaning. (There is a risk of electric shock and / or short circuit)

If the power cable is damaged this must be replaced by a fully qualiﬁed

electrician. (To avoid danger of electric shock, short circuit or ﬁre.

Cleaning Maintenance

1. To remove ﬁlters, slide up a little and

pull towards you .

2. Clean the ﬁlters with water or compressed air.

3. Clean evaporator and condenser units

with a vacuum cleaner or compressed air.

1. After cleaning, completely

dry the inside of the unit by

operating on 'Fan Mode'

only 3 to 4 hours.

2. Turn 'OFF' at control panel,

remove plug from socket.

Coil and store cable neatly.

3. Keep machine suitably

covered to prevent damage

by damp, humidity and dust.

Operating Instructions - ET 21 & 25

Click www.andrews-sykes.com or Call Us Free 0800 211 611

Control Panel Functions

1. Power: Use to power On / Off/.

2. ▲▼: Raises or lowers temperature and / or sleep (off) time.

3. Cool: Use to select cooling mode.

4. Lower Mode: Controls fan low speed.

5. High Mode: Controls fan high speed.

6. Off Timer: To set the length of time, once turned on, that you wish the cooler to

run for. You can set 0~24 hours. Time intervals are 30mins. up to 10 hours and

then 1 hour between 10 and 24 hours.

7. Remote: From the long distance, you can control the machine by wired remote

control.

8. Room: If the LED in ON, the displayed temperature is for room temperature. If

the LED if OFF, the displayed temperature is for spot temperature.

9. Comp: When the compressor is operating, the LED in ON.

10. Error: Error signal (E1: High pressure, E2: Low pressure, E3: Sensor, AF: Eva

freezing)

11. Water Full: Red light indicates ‘Tank Full’. The compressor will shut off

automatically. Empty tank and replace in position to resume operation. Fig. 2

12. Align Drain Tank: The red light indicates the water tank is not in the correct

position.

13. Display: Display Room / Spot temperature, and the setting temp and sleep

time in case of setting them. When the user set the sleep timer ‘hr’ will be

turned on. (Display of ‘LO’: under the 0ºC, display of ‘HI’: over the 50ºC)

START BY PRESSING THE ‘POWER’ BUTTON.

• Cooler will start up automatically

• To STOP the unit, press the ‘POWER’ button once again

To change fan speed, press the ‘LOW’ button.

If you wish to operate on fan only, press the ‘COOL’ button. To resume

cooling, press the ‘COOL’ button again. (NOTE: There is a 3 minute delay

when switching functions to protect the compressor)

To reduce the temperature of the entire room then select ‘Room / Area

cooling’. For targeted cooling of machinery, servers, or people etc, select

‘spot cooling’.

If you want to display room temperature, push cool and ▼ button

simultaneously for three seconds.

If you want to switch from centigrade to fahrenheit - push (up) ▲ and (down)

▼ button simultaneously for three seconds.

Control Panel Functions

When the power is on, the best set temperature is displayed. Default of set

temperature is 5ºC.

When you push either (up) ▲ or (down) ▼ button, the setting temperature

can be changed.

The display showing the set temperature will blink 3 times.

Limits of Room / Spot and setting temperature:

Room / spot temperature Setting temperature

0ºC - 5ºC 1ºC - 30ºC

Cooling operates when room / spot temperature is more than set temperature

Cooling stops when room / spot temperature is less than set temperature

Setting the timer

When cooler is operating, press the ‘OFF TIMER’ button and set the length

of time you want by pressing ▲ or ▼. Each time you press the button you

will increase the 'time to off' period by 30 minutes up to 10 hours, and 1 hour

thereafter up to 24 hours. The display will show .5 for 30 minutes and 1 for

an hour. e.g. 1 ½ hours will be shown as 1.5.

When you have ﬁnished setting the time period, the 'off timer' lamp will

illuminate, which indicates the cooler is in sleep (off timer) mode.

If you press the 'OFF TIMER' button during its operation, the remaining time

will be shown.

to CANCEL timing, press the 'OFF TIMER' button for ONE second, it will

then switch the timer off automatically.

Errors and Warnings

WATER FULL - Display shows FU

When the water container is full, FU is displayed and the LED 'Water full'

illuminate.

ALIGN WATER TANK -

If the water tank is not positioned correctly, the LED 'Align Drain Tank'

illuminate

HIGH PRESSURE -

'E1' is displayed and the 'Error' LED will be on when the pressure of the

compressor is too high and the high pressure switch is open.

LOW PRESSURE -

'E2' is displayed and the 'Error' LED will be on when the pressure of the

compressor is too low.

SENSOR PRESSURE -

If the thermistor is short circuited or cut, 'E3' is displayed and the 'error' LED

will be on

ANTI FREEZING -

When the temperature of the evaporator is below -4ºC, 'AF' is displayed and

the 'Error' LED will be on.

⑤

①

②

③④

⑦

⑧

⑩

⑪

⑫

⑬

⑨

⑥

FLEXIBLE DUCT OUTLET (COLD AIR)

HANDLE

DIGITAL CONTROLLER

CONDENSER OUTLET (HOT AIR)

EVAPORATOR FILTER

AMBIENT AIR INTAKE.

CONDENSER FILTER

CASTERS (FRONT LOCKABLE)

ELECTRIC PANEL

(ACCESS BY AUTHORISED SERVICE

PERSONNEL ONLY)

POWER PLUG

WATER LEVEL INDICATOR

TO CHECK WATER LEVEL OF THE

CONDENSATE TANK.

CONDENSED WATER TANK

TO COLLECT WATER GENERATED

DURING COOLING.

Errors and Warnings

Front View

Rear View

Operating Instructions - ET 21 & 25

Click www.andrews-sykes.com or Call Us Free 0800 211 611

Problem Likely Cause Solution

Not working

Power plug incorrectly

connected

Connect plug correctly

Power button OFF Press POWER button to ON

Blown fuse in mains plug Replace fuse (MUST BE 13 amp)

Fuse (supply) blown Exchange fuse in board

Breaker on switch board

tripped

Check load capacity and reset

Ambient temp. too high Use only below 45˚C (HSC-3500 : 40˚C)

Poor cooling

performance

Filter blocked with dust Clean ﬁlter

Dust in heat exchanger Clean heat exchanger

Obstacle against inlet

side

Remove and allow 50cm clearance

Ambient temp. too high Use only below 45˚C (HSC-3500 : 40˚C)

E1 Exhaust fan is not

operating

Check the power supply or replace

the motor

Hot air being restricted

from leaving the

machine

Unblock or relocate exhaust hose

E2 Refrigerant is leaking.

Check with manifold

gauge

Supply optimum refrigerant and check

the leakage. (By authorised service

personnel only)

E3 Thermistor sensor wire

is cut

Change the thermistor sensor

AF (Freezing) Evaporator is frozen

(Ambient temp. is under

20˚C)

Operate continuesly until “AF”

disappears or operate in “FAN” mode

Insulation exhaust Duct

This new insulated exhaust duct reduces diameter from 17" (43cm) down to 12"

(30 cm) thereby making it easier to handle. Being 3 metres long, it can either

be ducted out of a window or vertically up into a ceiling void. The duct is also

insulated which improves the cooling efﬁciency because heat is not being put back

into the room / are. (Max. exhaust duct length 9mtr)

The open end (12" diam) has a velcro cuff and this enables easy and efﬁcient ﬁtting

of out 3 metre extension lengths which also have velcro cuffs. Loops are tted to

both reducer duct and extensions should support be necessary.

Produktspecifikationer

Varumärke:	Andrews
Kategori:	Luftkonditionering
Modell:	ET 25
Färg på produkten:	Zwart
Vikt:	16800 g
Bredd:	362 mm
Djup:	340 mm
Höjd:	607 mm
Husmaterial:	MDF, Steel
Anslutningsteknik:	Bedraad
Genomsnittlig effekt:	1000 W
Equalizerinställningar:	Nee
Rekommenderad användning:	Universeel
Impedans:	8 Ohm
Ljudutgångskanaler:	1.0 kanalen
Högtalarplacering:	Vloer
Antal förare:	2
Bashögtalare:	Ja
Diameter drivrutin subwoofer (imperiaal):	1.5 "
Diameter drivrutin:	39 mm
Frekvensomfång:	50 - 20000 Hz
Känslighet:	132 dB
Typ av högtalare:	2-weg
Förstärkare:	Ingebouwd
Diameter woofer:	12 "
XLR in:	Ja
Tweeter:	Nee
Crossover frekvens:	1700 Hz
Audio RCA-ingångar:	1
Högtalarposition:	Voorkant
6,35 mm (1/4-tum) ingång:	1
Högtalare fram:	18GA