Antari SW-250 Bruksanvisning

Antari Snöslunga SW-250

Läs nedan 📖 manual på svenska för Antari SW-250 (31 sidor) i kategorin Snöslunga. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/31

SW-250/SW-250X

Wireless Control

High Output Snow Machine

User Manual

English Français Deutsch • • • 中文

UNPACKING & INSPECTION

Open the shipping carton and check that all equipment necessary to operate the machine arrived intact. have

The shipping carton should contain the followin items: g

1. Snow machine with power cable

2. W-1 wireless transmitter (Only for SW-250 model)

3. Fluid tank

4. Hanging bracket

5. Screw set and user manual

Before beginning initial setup of your ANTARI - /SW- Snow Machine, make sure that there is no SW 250 250X

evident damage caused by transportation. In the event of a damaged cable or unit housing, do not plug it in

nor use it until contacting your Antari dealer for assistance.

SETUP and POWER ON

1 move all packing materials from shipping box. Check that all foam and plastic paddings are removed. . Re

2. Place the machine on a at surface and follow the steps below.

Tank cap

Tank

Filter

PU Liquid Tube

Adaptor

with Nut

A ssem blin g Tank & Filter

Please note that "adaptor with nut"

set must be tightly connected.

3. Assemble the hanging bracket on the machine, use the M8 screws to position the hanging bracket

with the machine, the tightening screws are for adjusting the machine’s angle when in the air.

Assembling Hanging Bracket

Assemble 4 washers on both inner sides of the hanging

bracket w ith M8 screw s on outer sides as indicated.

Hanging Bracket

M8 Screw

Tightening

Scr ew

Washer

4. Fill with ANTARI SL-5(A) s uid. Any other types of fluid can damage the unit. When lled, place cap now

back on liquid tank.

5. Plug the power cable into a grounded electrical outlet and ip the power switch at the rear of the machine

for powering on.

TRANSMITTER REGISTRATION

ONLY FOR SW-250 MODEL

After powering on, the LCD screen will show sequentially Antari SW- and then Wireless Setup . Press “250” “ …”

button A on the transmitter(s) to register when “ ” “Wireless Setup visible. There is a total of 15 seconds to …” is

nish the registration of the transmitter(s). Once registration is completed, the LCD screen will blink and beep.

The LCD screen will nally show Wireless Setup once the 15 seconds ends. Up to 5 transmitters are “OK”

allowed to be registered with one SW- The included transmitter has been registered with the machine 250.

before shipment and can be directly operated without any start-up setting. Therefore, the registration is only

needed before use of new W- 1.

Note: All transmitter(s) registration must be completed within 15 seconds or SW-250 has to be power on

again for next registration.

LCD CONTROL OPERATION

After transmitter(s) registration time ends, LCD screen will then show To Snow Now the machine is “Ready ”.

ready for operating.

FUNCTIONS SETTING

Press for setting dierent functions per sequence as below. Menu button

Interval Set Up/Timer Set the interval time under timer mode by pressing and

Down/Volume buttons (20 to 2000 seconds).

Duration Set Up/Timer Set the duration time under timer mode by pressing and

Down/Volume buttons (10 to 200 seconds).

Timer Out Up/TimerSet the output volume under timer mode by pressing and

Produktspecifikationer

Varumärke:	Antari
Kategori:	Snöslunga
Modell:	SW-250
Färg på produkten:	Green, Orange
Bredd:	3710 mm
Djup:	1190 mm
Höjd:	1920 mm
Maximal viktbelastning:	50 kg
Rekommenderad ålder (max):	12 jaar
Rekommenderad ålder (min):	3 jaar
Cast design:	Vrijstaand
Material:	Metaal
Montering krävs:	Ja
Typ produkt:	Playground slide
Fälla:	Ja
Antal steg på stegen:	4 stappen
Rutschbanans längd:	3.32 m