Anthro MiniCart Bruksanvisning
Läs nedan 📖 manual på svenska för Anthro MiniCart (2 sidor) i kategorin Byrå. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/2
TECHNOLOGY FURNITURE®
Anthro MiniCart
Assembly Instructions
01– Insert Screws ............................ Qty. 4 325-5052-00 ....................
02– 2 3/8” Non-Locking Casters ........ Qty. 2 150-5002-03 ................... *
03– Caster Inserts ........................... Qty. 4 525-1000-00 .................... *
04– 2 3/8” Locking Casters ................ Qty. 2 150-5003-03 .................. *
05– 1.75” Large End Caps ................ Qty. 2 175-5021-xx ......................
06– Base Tube Screws ............................. Qty. 3 .....................325-5000-00
07– MiniCart Base Tube ................... Qty. 1 125-5004-xx .....................
08– Self-threading Screws ...................Qty. 6 325-5010-00 ......................
09– Vertical Legs ............................ Qty. 3 .................................................
23.875” Vertical Legs (GT23xx) ...... ................................. 125-5020-xx
Enclosed Parts List
Detailed views of all hardware is provided with each
assembly step.
10– 1-5/8” Screws ....................................Qty. 6 325-5086-00 .....................
11– Shelf Supports ...................................Qty. 6 175-5060-xx ......................
12– Shelf Clamps ......................................Qty. 6 175-5059-xx ....................
13– MiniCart Shelves ....................... Qty. 2 100-6003-xx ......................
14– 1.5” Small End Caps .................. Qty. 3 175-5020-xx ......................
All fastener quantities listed here are the minimum needed for your
cart assembly. Your shipment may include a few extras.
Cable Management Components
Cable Alley, 9” Qty 1 175-5061-03 ...................... .............................................
Cable Alley, 3” Qty 1 175-5062-03 ...................... .............................................
Cord Handler Qty 1 175-5001-03 ........................ .............................................
Self-threading Screws...... Qty 6 325-5010-00 ..............................................
Anthro® Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062
SAVE THESE INSTRUCTIONS! Document # 300-5068-00
Step 7
Install all four caster inserts into the base tube and secure
(fully tighten) with one Caster Insert Screw per insert.
Next, push the casters, (locking ones in front) into the caster
inserts.
Step 8
Carefully rotate the shelf assembly , upside down (from Step 6)
as shown.
Place the base tube assembly onto the vertical (from Step 7)
legs of the shelf assembly.
Attach the base tube to each leg using a total of three
3-1/2” Bolts.
Tighten all Self-threading and Base Tube Screws.
Step 9
Rotate your MiniCart over onto the casters.
Pop the three 1.5” small end caps into the vertical legs and
the two 1.75” large end caps into the base tube.
After you add your equipment to the cart, select the cable
management components that suit.
To install the Cable Alleys, expand each sleeve and fit it over
a cart leg. Align the mounting hole(s) in the sleeve with the
holes on the leg, then install with self-threading screws.
To install the Cord Handler, snap the large end around any
cart leg, then route cables through the small end.
Congratulations! Your MiniCart assembly is complete.
Please return the enclosed Registration Card to receive our
product updates, new catalogs, and sale flyers.
Thank you for choosing Anthro!
January 2015, Rev D
These Assembly Instructions are for
the GT23xx.
Before beginning assembly of your
Anthro MiniCart, please take a moment to
review the parts list below to verify that
your shipment is complete.
Does your Cart have 4” Casters?*
Then these are your casters:
4” Locking Caster
150-5011-03
4” Non-Locking Caster
150-5010-03
Questions? 1-800-325-3841
04 06
07
03 02
09
10
05
12
01
08
11
14
13
1.5” Small End Cap
1.75” Large End Cap
3-1/2” Bolt
325-500 0-00
TOOLS
To make the assembly of your cart even
easier, we have included all of the required
tools . Use the handy Hex Driver Bit in your
electric drill in place of the Hex Driver.
Hex Driver 5/32”.................. 375-5000-00
Hex Driver Bit 5/32” 375-5003-00 ...........
8 oz. Rubber Mallet............ 375-5022-00
1/2” Caster Insert Screw
325-505 2-00
Locking Casters
Anthro MiniCart
Assembly Instructions
Anthro® Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062
Step 1
Before proceeding, please review the Assembly Instructions
of all Anthro products you purchased and are planning to
include in this installation.
Step 3
Attach three shelf supports to each shelf.
Begin by first installing a shelf clamp into the shelf notch.
Be sure the pointed barbs face towards the outer shelf
edge.
Next, slide a shelf support into the recesses of the shelf
clamp and shelf. Push in as far as possible.
Finally, secure with a 1-5/8” Clamp Screw (325-5086-00).
anthro.com
Step 4
Loosely attach one shelf to hole 14 from the bottom (coped end)
of one vertical leg using a Self-threading Screw. These fasteners
are cutting threads into the leg, so the first few turns will require
some force.
NOTE: This will place your lower shelf 22” from the floor using the
standard 2 3/8” casters.
Step 5
Loosely attach the remaining shelf to hole 2 from the top
(non-coped end) (from Step 4) of the vertical leg assembly
using one Self-threading Screw.
NOTE: Handle the shelf assembly carefully until the cart is fully
assembled.
Step 6
Loosely attach the 2nd and 3rd vertical legs to the shelf
assembly using one Self-threading Screw per (from Step 5)
shelf support.
TIP: Use the holes in the vertical legs as a ruler to ensure that
your Self-threading Screws are installed into the correct
locations.
Questions? 1-800-325-3841
First
Next
Finally
Barbs
Step 2
Decide on the shelf locations for your MiniCart. You can
place your shelves almost anywhere on the vertical legs (the
legs are stamped at 1” increments).
For a lower shelf location that is higher or lower than
19” from the floor, refer to the illustrations shown at right to
determine which holes to attach your lower shelf.
Once your MiniCart is assembled, it’ll take a little effort to
remove and reinstall it. Measure, measure, measure.
NOTE: These instructions will place your lower shelf 19” from
the floor using the standard 2 3/8” casters.
GT23xx with 2 3/8” Casters
GT23xx4 with 4” Casters
Hole 12=20”
Hole 11=19” (measured from the coped end)
Hole 10=18”
Hole 11=20”
Hole 10=19”
Hole 9=18”
REMINDER: You may want to
measure your equipment to make
sure it fits between the selected
shelf locations and adjust your
assembly as needed
Coped end
19”
19”
GT23xx
Overall MiniCart height is
28” using 2 3/8” casters
NOTE: Add 1” to overall height for 4” casters and subtract 3” from
overall height for glides.
Bottom
(coped)
end
Hole 14=22”
(using 2 3/8” Casters)
Insert one Self-threading Screw
through each Shelf Support
Top
(non-coped)
end Hole 2
Top
(non-coped)
end
Bottom
(coped)
end
NOTE: These Instructions will create
approximately 6” of usable space
between your shelves.
Lower Shelf
Self-threading Screw
325-5 0-0001
Self-threading Screw
325-5 0-0001
Self-threading Screw
325-5 0-0001
1-5/8" Screw
325-5086-00
Produktspecifikationer
| Varumärke: | Anthro |
| Kategori: | Byrå |
| Modell: | MiniCart |
Behöver du hjälp?
Om du behöver hjälp med Anthro MiniCart ställ en fråga nedan och andra användare kommer att svara dig
Byrå Anthro Manualer
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
18 September 2024
Byrå Manualer
- Byrå IKEA
- Byrå Ahrend
- Byrå Aeris
- Byrå Jysk
- Byrå Bush
- Byrå Sharkoon
- Byrå United Office
- Byrå Thermaltake
- Byrå Techly
- Byrå BDI
- Byrå Paidi
- Byrå Livarno
- Byrå Sandberg
- Byrå Digitus
- Byrå Insignia
- Byrå Genesis
- Byrå Fellowes
- Byrå MADE
- Byrå Habitat
- Byrå Foppapedretti
- Byrå Cooler Master
- Byrå Victor
- Byrå Corsair
- Byrå Newstar
- Byrå Hooker
- Byrå Butler
- Byrå Alpha Gamer
- Byrå Cougar
- Byrå Chief
- Byrå Arozzi
- Byrå Gamdias
- Byrå Bell'O
- Byrå Four Hands
- Byrå Lian Li
- Byrå Durable
- Byrå Kogan
- Byrå ThunderX3
- Byrå Bretford
- Byrå Zomo
- Byrå X Rocker
- Byrå AeroCool
- Byrå Ultradesk
- Byrå HON
- Byrå Lazy Maisons
- Byrå Worktrainer
- Byrå Zaor
- Byrå Glorious
- Byrå OKA
- Byrå Game Shark
- Byrå Seville Classics
- Byrå Yaasa
- Byrå CoolerMaster
- Byrå FOURZE
- Byrå Overdrive
- Byrå Xtech
- Byrå Ergolux
Nyaste Byrå Manualer
10 December 2024
8 December 2024
8 December 2024
8 December 2024
8 December 2024
8 December 2024
8 December 2024
8 December 2024
8 December 2024
8 December 2024