AS Synthesizers Dual ENV AS301 Bruksanvisning

Läs nedan 📖 manual på svenska för AS Synthesizers Dual ENV AS301 (3 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/3
BLOCK DIAGRAM OF
DUAL ENV
AS301
MIXED SIGNAL MODULE
12 3 4 5 6
7 8 9 10 11 12
20 21 22
1819
2324
282925 26 27
13 14 15 16 17
1. GATE1 in for ENV1 (can linked to GATE2)
2. Indicator of GATE1 in
3. TRIG1 in for ENV1 (can linked to TRIG2)
4. Indicator of TRIG1 in
5. ENV1 positive out, range: 0V to +10V
6. ENV1 negative out, range: 0V to -10V
7. GATE2 in for ENV2
8. Indicator of GATE2 in
9. TRIG2 in for ENV2
10. Indicator of TRIG2 in
11. ENV2 positive out,
range: 0V to +10V / -5V to +5V
12. ENV2 negative out,
range: 0V to -10V / +5V to -5V
13. ENV1 mode: gate or trigger *
14. ENV1 curve: linear or exponential
15. ENV2 mode: gate or trigger *
16. ENV2 curve: linear or exponential
17. ENV2 offset: 0V/10V or -5V/+5V
18. ENV2 delay time: 0s to 2s
19. ENV2 in delay phase indicator
20. ENV1 attack time: 2ms to 10s
21. ENV1 decay time: 2ms to 10s
22. ENV1 sustain level: 0V to +10V
23. ENV1 release time: 2ms to 10s
24. ENV1 output indicator
25. ENV2 attack time: 2ms to 10s
26. ENV2 decay time: 2ms to 10s
27. ENV2 sustain level: 0V to +10V
28. ENV2 release time: 2ms to 10s
29. ENV2 output indicator
* ENV ignores TRIG signal when mode
switch in GATE position. This way the ENV
won’t get restarted by TRIG signal.
Incoming TRIG signal restarts ENV when
mode switch in TRIGGER position.
FRONT PANEL OF
DUAL ENV
AS301
MIXED SIGNAL MODULE
5
4
1
1. Power bus connector IDC10
2. Factory programmer port
3. USB for fi rmware upgrade
4. GATE & TRIG inputs from internal rails
and GATE & TRIG links ENV1 to ENV2
When no use of input pins, connect
jumper between input and GND.
Linking GATE and TRIG. inputs between
ENV1 and ENV2, remove jumper from
ENV2, TRIG and GATE inputs.
5. ENV outputs to internal rails
Do not use jumpers on output
pins, also do not connect to ground or
power rails!
FIRMWARE UPGRADE:
1. Download Dual ENV fi rmware
from our website
2. Turn off your modular system
3. Connect Micro USB cable to Firmware
upgrade port
4. Turn on your modular system
5. Module’s library appears in pop-up
window
6. Drag and drop downloaded fi le into
pop-up window
7. When upload is done turn off your
modular system and disconnect USB
cable.
8. Restart your modular system and enjoy
9. If upload process was unsuccessful,
repeat the whole procedure.
TECHNICAL SPECIFICATION
Module depth: 33mm
Module width: 16HP (80.4mm)
Module weight: 215g
Connector type: 10P IDC Eurorack
Power consumption:
+12V / 90mA & -12V / 10mA
Analog outputs: True Rail-to-Rail
Analog outputs range:
0V to +10V or -5V to +5V
Digital inputs range: 0V /+5V
Digital inputs pulse time: min 1ms
BACK PANEL OF
DUAL ENV
AS301
MIXED SIGNAL MODULE

Produktspecifikationer

Varumärke: AS Synthesizers
Kategori: Inte kategoriserad
Modell: Dual ENV AS301

Behöver du hjälp?

Om du behöver hjälp med AS Synthesizers Dual ENV AS301 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad AS Synthesizers Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer