Astralpool RTX Robotic Pool Cleaner Bruksanvisning

Astralpool Diverse RTX Robotic Pool Cleaner

Läs nedan 📖 manual på svenska för Astralpool RTX Robotic Pool Cleaner (15 sidor) i kategorin Diverse. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/15
RTX Robotic Pool Cleaner
Product 11711
Product Inst 321
Operating Instructions
with Top Access
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL THE INSTRUCTIONS
CAUTION: Do not plug the power supply into a grounded outlet or do not switch the
pool cleaner “ON” if it is not fully immersed in water. Operating the cleaner out of water
will cause severe damage immediately and will result in loss of warranty.
Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its
cleaning cycle. This will allow the motors to cool adequately. Do not leave the cleaner
in the pool all the time. Always remember to turn the power supply “OFF” and unplug it
from the power outlet before removing the cleaner from the pool.
WARNING: The cleaner must not be used when people are in the water. For use
with swimming pool only
Safety Note
- The unit must be supplied through a residual current device (RCD) having a rated
residual operating current not exceeding 30 mA
- The connection to the branch circuit should be consistent with the local and national
wiring rules (electrical code).
- Mishandling of the unit can result in leakage of lubricants.
- If the supply cord is damaged, it must be replaced by the manufacturer’s service
agent or a qualified and trained person in order to avoid hazards.
Dear Customer,
Thank you for choosing our product to clean your pool. We hope that you will enjoy
using your new robot to maintain your swimming pool for years to come.
Before you begin to use your robot, please take a few minutes to carefully read these
operating instructions.
Again, thank you for choosing our product.
2
Components
Your new automatic pool cleaner contains:
- The robotic pool cleaner with its floating cable.
- The Power Supply (transformer).
- Caddy
Please read this manual completely before operating your pool cleaner.
While the appearance of your cleaner and some of its components may differ from those
shown here, the function of the cleaner, operating procedures and maintenance
practices are the same.
WARNING: A Ground Fault Current Interrupter (GFCI-USA) or a Residual Current
Device (RCD-EUROPE) must be installed to protect your electric outlet and prevent
any possible electric shock.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
SAVE THESE INSTRUCTIONS
Drive Track
Scrubbing Brush
Unit Body
Filter Top
Access
Handle
FIlter Lock
Release
Outlet Top
Side Plate
Handle Lock
Mechanism
12 cm
(4 inch)
3.6m/11.8ft
1
1a
1. Place the power supply (transformer) at least 3.6 meters / 11.8 feet from the pool and at
least 12 cm / 4 Inch above the surface (fig.1). The transformer will supply low voltage to
the cleaner.
2. Uncoil the cable.(fig.1a)
3. ONLY FOR MODELS WITH FLOATING HANDLE - For proper operation, lock
the moveable handle diagonally across the top of the cleaner's body. Push down
on the handle lock mechanism and slide the handle all the way to the end, then
release the lock. Depending on your model, the handle lock button might be
vertical or horizontal (fig.2a, 2b). The handle will remain fixed in this position.
Repeat this process on the other side of the cleaner.
Remember, the handle must be fixed diagonally (fig.2c)
2b
unit
2c2a Handle lock vertical Handle lock horizontal
Operating the pool cleaner
4. Place the unit in the water. Turn the unit
side to side in the water to allow air to
escape from the body and then let the
cleaner sink to the bottom of the pool
(fig.3). Then, spread the cable over the
surface of the pool as evenly as possible
(fig.1).
5. Plug the cable into the power supply.
Make sure the key on the plug corresponds exactly with the key slot on the socket of
the power supply (fig.3a).
Plug the power supply into a grounded outlet. Ensure that the electric outlet has been
properly grounded (fig.3b). The light will glow indicating that the system is “ ON and
the pool cleaner will start the cleaning cycle. The unit keeps record of the number of
cleaning cycles. Only an authorized service center can display the accumulated
cleaning cycles. (See details on the next page)
3
3
3b
3a

Produktspecifikationer

Varumärke: Astralpool
Kategori: Diverse
Modell: RTX Robotic Pool Cleaner

Behöver du hjälp?

Om du behöver hjälp med Astralpool RTX Robotic Pool Cleaner ställ en fråga nedan och andra användare kommer att svara dig




Diverse Astralpool Manualer

Diverse Manualer

Nyaste Diverse Manualer