Atdec AD-TVAC-CM-B Bruksanvisning

Atdec Inte kategoriserad AD-TVAC-CM-B

Läs nedan 📖 manual på svenska för Atdec AD-TVAC-CM-B (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/6
Installation Guide
AD-TVAC-CM
AD-TVAC-CM Page 1 of 6
REQUIRED TOOLS
AV Cart Camera Mount
COMPONENT CHECKLIST
Upright
Bracket
Camera
Shelf
M5x8
Screw
(x2)
M5x10
Screw
(x2)
M6x10
Screw
(x2)
5mm
Hex Key
M6
Flange
Nut
Washer
(x2)
4mm
Hex Key
Spanner
• Phillips Head Screwdriver
0 - 5kg
(0 - 11lbs)
WEIGHT RANGE
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Please ensure your preferred device is securely fastened to the mount prior to use or movement.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to assemble this product correctly may cause serious injury/death during or following installation.
! This product should only be installed by professional installers of good mechanical aptitude, who fully understand these
instructions and the consequences of incorrect installation.
! Do not over tighten screws.
! Two person installation is recommended.
! Product not suitable for use outdoors.
! After installation is complete check to verify that AV Cart is secure and safe for use.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and
offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may
be within the stated range. Please contact Atdec if you would like further information.
! WARNING! Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or
toys placed on the cart may encourage a child to climb on the cart and as a result the cart may tip over on to the child.
AD-TVAC-CM Page 2 of 6
COMPATIBILITY
1. Construct the Camera Mount Assembly
A2. Attach the Camera Mount Assembly to the cart
A - FOR AD-TVC-20 CART
AD-TVAC-CM Page 3 of 6
> 4 mm
Attach Camera Shelf to Upright Bracket B A
with M5 Screws . C
For AD-TVC-70A, loosen the screws on the
pre-installed silver clamp plate using Hex Key .D
Leave a 4mm gap between the clamp plate and
upright bracket.
For AD-TVC-20 AD-TVC-45 AD-TVC-75, and ,
remove the silver clamp plate completely.
A2.1. Remove the rubber cable management
grommet from the slot on the cart.
A2.2. Determine the two holes needed on
Upright Bracket to hold the Camera A
Mount Assembly at the desired height.
A2.3. With assistance, hold the Camera Mount
Assembly sideways (as illustrated)
and align the lower of the two holes
with the hole directly above the cable
management slot on the cart.
A2.4. Insert M6 Screw with Washer through H J
Upright Bracket and into the hole on A
the cart.
A2.5. I Attach M6 Flange Nut to M6 Screw H
inside the cart column through the cable
management slot. Tighten using 5mm
Hex Key .D
Use Spanner to support M6 Flange TIP: F
Nut whilst tightening M6 Screw .I H

Produktspecifikationer

Varumärke: Atdec
Kategori: Inte kategoriserad
Modell: AD-TVAC-CM-B

Behöver du hjälp?

Om du behöver hjälp med Atdec AD-TVAC-CM-B ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Atdec Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer