Atlona AT-VTP-550 Bruksanvisning

Läs nedan 📖 manual på svenska för Atlona AT-VTP-550 (9 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/9
Installation Guide
AT-VTP-550
1
Velocity 5.5” Touch Panel
AT-VTP-550-WH and AT-VTP-550-BL
The Atlona AT-VSP-550-BL and AT-VTP-550-WH are 5.5” touch panels in black and white,
respectively, for the Atlona Velocity™ Control System. They feature contemporary, rened styling
for modern presentation environments with 720x1280 native resolution, and a capacitive glass
surface that supports multi-touch and gesture interactions. These touch panels conveniently
install into a wall or furniture via a US or Euro one-gang opening. The VTP-550-BL and VTP-550-
WH feature Power over Ethernet (PoE), enabling a single network connection for data and power.
Setting up the touch panels is eortless as the AV control GUI is automatically uploaded from the
Velocity Control Gateway processor during system conguration.
1 x AT-VTP-550
1 x Metal mounting plate
4 x Mounting screws
1 x Installation Guide
Package Contents
Operating Notes
The Velocity 5” Touch Panel (AT-VTP-550) must be on the same network as the Velocity
Gateway (AT-VGW-HW) or it will be unable to sync for control.
The AT-VTP-550 is PoE capable, to power the unit, simply plug it into a 802.3at compatible
network switch. If the network switch is not PoE capable, a PoE injector (purchased separately)
can be used.
IMPORTANT: Velocity Gateway (AT-VGW-HW) must be set up before the AT-VTP-550 is
fully functional.
Installation Guide
AT-VTP-550
2
Mounting Instructions
The AT-VTP-550 can be mounted to a 1 gang back plate.
1 Select the type of 1 gang back box to use and install into a wall.
2 Thread the Ethernet cable through the 1 gang box.
3 Install the included mounting plate into the 1 gang box.
a If using a UK back box, place the screws in the two inside mounting holes.
b If using a US back box, place the screws through the outside screw holes.
4 Loosen or remove the two screws located at the top and bottom of the unit.
5 Place the unit onto the metal back plate, the dual prongs inserting into the small opening on
the back of the unit.
6 Tighten/attach the screws at the top and bottom of the touch pad.
NOTE: Install using the region’s safety guidelines for electrical boxes.
NOTE: To avoid damage to the unit, do not overtighten the screws.
24V DC / 0.5A
LAN / PoE
802.3af c om pliant
Installation Guide
AT-VTP-550
3
24V DC / 0.5A
LAN / PoE
802.3af compliant
Installation and Set Up
1 Connect the Ethernet cable into the back of the unit.
a If the Ethernet cable is connected to a non PoE switch, use a PoE injector using 802.3at
(purchased separately).
2 Secure the unit in either the wall or optional stand, as explained in the mounting instructions.
3 The Velocity logo will display during the booting process and will go directly into setup.
Press to start the setup process.CONTINUE
NOTE: Installation of the Velocity Touch Panel can only be done after Velocity has
been set up. View the installation guides for VGW-HW/VGW-SW and Velocity Manual
for instructions.
Initial Setup
CONTINUE
You will be guided through the setup process
in the next few screens.
Velocity Device Setup
Wired
Address
Device
Alias
Panel Settings
Velocity
URL
Enable
HTTPS
0.0.0.0
Velocity Touch Panel
10.0.0.123
SCAN FOR GATEWAYS
SAVE AND CONTINUE
PANEL SETTINGS
4 The unit will load a new screen. Change the Device Alias (if needed) to help dierentiate
when there are multiple touch panels at a site. A new screen will open.

Produktspecifikationer

Varumärke: Atlona
Kategori: Inte kategoriserad
Modell: AT-VTP-550

Behöver du hjälp?

Om du behöver hjälp med Atlona AT-VTP-550 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Atlona Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer