Audio-Technica ATW-R900A Bruksanvisning

Audio-Technica mottagare ATW-R900A

Läs nedan 📖 manual på svenska för Audio-Technica ATW-R900A (8 sidor) i kategorin mottagare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/8
System 9
VHF Wireless System
Installation and Operation
ATW-901a/G
Guitar System
ATW-901a/H
Headworn Microphone System
ATW-901a/L
Lavalier Microphone System
ATW-902a
Handheld Microphone System
PEAKRF
1 2 3 4
CHANNEL
System 9 Installation and Operation
2
This devic lie comp es w th part i 15 of the FCC Rul t t es. Opera ion is bjsu ec
to th e ti condi on that t devi mhis ce does not cause har fu tel in rfe e. renc
A copy of the declaration of conformity can be found on the internet at
www.audio-technica.com.
This device complies with Industry Canada license- empt RSS ex
standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio empts de licence. L'exploitation est ex
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
CAUTION! Electrical shock can result from rem al of the receiver ov
serviceable parts inside. Do not expose to rain or moisture.
The circuits inside the receiver and transmitter h e been precisely av
adjusted for optimum performance and compliance with federal
regulations. Do not attempt to open the receiver or transmitter. To do so
will void the warranty, and may cause improper operation.
Notice to individuals with implanted cardiac pacemakers or AICD
devices:
Any source of RF (radio frequency) energy may interfere with normal
functioning of the implanted device. All wireless microphones have
low-p er transmitters (less than 0.05 watts output) which are unlikely ow
Ho ver, since a “body-pack” mic transmitter typically is placed against we
the body, we suggest attaching it at the belt, rather than in a shirt
pocket where it may be immediately adjacent to the medical device.
Note also that any medical-device disruption will cease when the RF
transmitting source is turned off. Please contact your physician or
medical-device provider if you h e any questions, or experience any av
problems with the use of this or any other RF equipment.
Thank you for choosing an Audio-Technica professional wireless
have chosen our products because of their quality, performance and
reliability. This wireless microphone system is the successful result of
years of design and manufacturing experience.
Audio-Technica’s System 9 is a four-channel frequency-agile wireless
system designed to provide rock-solid performance along with
easy setup and clear, natural sound quality. Featuring stackable,
contemporary styling, System 9 is ailable in handheld, headworn, av
compatible user-switchable channels in one of four ailable VHF av
frequencies (169.505, 170.245, 171.045, and 171.905 MHz).
Each Sys m fes nte 9 pro sio al VH i l yF w re ess s ste nc udem i l s a cere iver
and i y-pac e ther a bod k transmitter or l a handhe d mi e/ an microp onh tr s tter.
ATW 0-9 1a UniPak
® b yod -pack tran tsmi ter systems include d mo els
pr -pe acka i i AT- it l Gged w th e ther an GCW gu ar cab e (/ ), a PRO EcW 8H
headworn cropho mi ne (/H), or a lavali mier c (/L) or partf icu r at nsla ap licp io .
All A-T W el Eir ess ssen stial ® h microp ones and ca s, av e ble ailabl se rapa tely,
ar e-te nated e r p rmi f i ny ATW 0or use w th a -9 1 system.
Because System 9 packaging is designed to hold all versions
of the system, some compartments in the carton may be intentionally
left empty.
The ATW-R900a receiver includes a switching power supply that
automatically adapts to changes in mains voltage.
The versatile ATW-T901a UniPak body-pack transmitter has both
a high-impedance input for instruments, and a low-impedance input
with bias connection for use with dynamic and electret condenser
microphones. The ATW-T902a handheld transmitter features a
unidirectional dynamic microphone element.
Both the body-pack and handheld transmitters use internal AA batteries
and h e Power/Mute switches and input Trim (l el) adjustments.av ev
Receiver Installation
Location
For best operation the receiver should be at least 3' (1 m) ab e the ov
ground and at least 3' (1 m) y from a wall or metal surface to awa
sources such as digital equipment, motors, automobiles and neon
lights, as well as away from large metal objects. In multi-channel
systems, position receivers at least 3' (1 m) apart and keep operating
transmitters at least 6' (2 m) from the receivers to help assure
maximum RF performance.
Output Connections
There are two audio outputs on the back panel: balanced and
unbalanced. Use shielded audio cable for the connection between the
receiver and the mixer. If the input of the mixer is a 1/4" jack, connect a
cable from the 1/4" unbalanced audio output on the back of the receiver
housing to the mixer. If the input of the mixer is an XLR-type input,
connect a cable from the balanced XLR-type audio output on the back
panel to the mixer.
Power Connection
Connect the DC plug on the included AC p er adapter to the DC ow
p er input on the back of the receiver. Secure the cord over the cord ow
hook on the back of the receiver, to keep the plug from being detached
by an accidental tug on the cord. Then plug the adapter into a standard
120 Volt 60 Hz AC p er outlet. ow
(Note that the receiver has no p er Off/On switch. The receiver will be ow
energized when er the power adapter is connected and plugged into ev
the AC outlet. Unplug the p er supply from the AC outlet when the ow
system is not in use — both for safety, and to conserve energy.)
Antennas
A n el “dipole” antenna system on the receiver improves operation ov
by providing a “ground” element in addition to the usual “signal”
element. Position the two antennas at 90° in the form of a “V,” or
position the left (“signal”) antenna vertically and the right (“ground”)
antenna horizontally, in the shape of an “L” (Fig. A). Use the position
that performs better in your operating environment. Be certain to
extend both antennas to their full 15" (38 cm) length by holding them at
their bases and pulling out on their caps. Both antenna elements may
be swiveled to the left and right, but do not attempt to rotate them in a
screwing/unscrewing motion. To do so may damage the antenna and/or
receiver. For best performance, locate the receiver so its antennas are
in direct line-of-sight to the transmitter’s likely operating position.
System 9 Installation and Operation
3
1234
CHANNEL
1234
CHANNEL
Receiver Controls and Functions
Figure A — Front Panel Controls and Functions
1. ANTENNAS: Position the “signal” antenna (1a) and
“ground” antenna (1b) as shown to the right and above right. Fully
extend both antennas by pulling on the endcaps.
2. RF INDICATOR: Lights to show presence of transmitter signal.
3. CHANNEL SELECT BUTTON: Soft-touch button selects channel.
4. CHANNEL INDICATOR LIGHTS: Lights to show which channel is
selected. A channel indicator LED will light when power is applied
to the receiver.
5. AF PEAK INDICATOR: Only lights when audio distortion
is present at maximum modulation. Not affected by
position of Volume control.
Figure B — Rear Panel Controls and Functions
1. SQUELCH CONTROL: Adjusts level of noise-muting circuit
(preset at factory but can be adjusted as circumstances warrant).
2. VOLUME CONTROL: Adjusts the audio level at the
1/4" and XLRM
output jacks. Does not affect AF Peak indicator.
3. UNBALANCED AUDIO OUTPUT JACK:
1/4" TS (Tip-Sleeve) or “mono”
phone jack. Use a shielded cable to connect to an unbalanced
4. BALANCED AUDIO OUTPUT JACK: XLRM-type connector. A
standard 2-conductor shielded cable can be used to connect the
receiver output to a balanced microphone-level input on a mixer or
5. POWER INPUT JACK: Connect the DC plug from the
included AC adapter.
6. CORD HOOK: Loop the cord around the cord hook to keep
the DC plug from pulling out accidentally.
PEAKRF
1234
CHANNEL
MIN.
SQUELCH VOLUME UNBALANCED
BALANCED
DC 12V IN
500mA
MAX. MIN. MAX.
1a 1b
2 53 4
1 2 3 54 6

Produktspecifikationer

Varumärke: Audio-Technica
Kategori: mottagare
Modell: ATW-R900A

Behöver du hjälp?

Om du behöver hjälp med Audio-Technica ATW-R900A ställ en fråga nedan och andra användare kommer att svara dig


mottagare Audio-Technica Manualer

Audio-Technica

Audio-Technica ATW-B80WB Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica AEW-5000a Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica AT-PEQ30 Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica ATW-R3210N Bruksanvisning

25 Augusti 2024
Audio-Technica

Audio-Technica ATW-R900A Bruksanvisning

22 Augusti 2024
Audio-Technica

Audio-Technica ATW-RU13 Bruksanvisning

9 Augusti 2024

mottagare Manualer

Nyaste mottagare Manualer

Alto

Alto D1 Bruksanvisning

16 Januari 2025
Alto

Alto MC700.4 Bruksanvisning

16 Januari 2025
Alto

Alto MC250.4 Bruksanvisning

16 Januari 2025
Alto

Alto MC250.8 Bruksanvisning

16 Januari 2025
Alto

Alto D4 Bruksanvisning

16 Januari 2025
Alto

Alto D3 Bruksanvisning

16 Januari 2025
Alto

Alto MC500.4 Bruksanvisning

16 Januari 2025
S.M.S.L

S.M.S.L PA200 Bruksanvisning

15 Januari 2025
Peavey

Peavey CKd 608 Bruksanvisning

15 Januari 2025
Wavtech

Wavtech link700.4plus Bruksanvisning

14 Januari 2025