Axxess HDCC-02 Bruksanvisning

Axxess Inte kategoriserad HDCC-02

Läs nedan 📖 manual på svenska för Axxess HDCC-02 (8 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

Installation instructions for part HDCC-02

REV. 5/27/2016 INSTHDCC-02

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Provides NAV outputs (parking brake, reverse, speed sense)

• Pre-wired ASWC-1 harness (ASWC-1 sold separately)

• Retains factory backup camera

• Retains LaneWatch camera

• Retains ability to change factory clock and date

• Retains factory AUX-IN jack

• Can be used in non-amplified, or amplified models

• High level speaker input

• Retains balance and fade

• Micro “B” USB updatable

FEATURES

• Cutting tool • Crimping tool • Tape • Connectors

(example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

• HDCC-02 interface • HDCC-02 harness

INTERFACE COMPONENTS

APPLICATIONS

HONDA

Civic 2014-2015

CR-V 2015-up

HDCC-02

Connections to be made

From the HDCC-02 harness to the aftermarket radio

(a) Main harness:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the accessory wire.Red

• If the vehicle is equipped with a factory amp, connect the wire to Blue/White

the amp turn-on wire.

Note: This wire must be connected to hear sound from the factory amplifier.

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

• Connect the wire to the right front positive speaker output.Gray

• Connect the wire to the right front negative speaker output.Gray/Black

• Connect the wire to the left rear positive speaker output.Green

• Connect the wire to the left rear negative speaker output.Green/Black

• Connect the wire to the right rear positive speaker output.Purple

• Connect the wire to the right rear negative speaker output.Purple/Black

(b) 16-pin harness:

• Connect the wire to the illumination wire (if the aftermarket Orange/White

radio has no illumination wire, tape off and disregard this wire).

The following (3) wires are for aftermarket multimedia/navigation radios that

require these wires:

• Connect the wire to the parking brake wire (if applicable).Light Green

• Connect the wire to the speed sense wire (if applicable).Blue/Pink

• Connect the wire to the reverse wire (if applicable).Green/Purple

• Connect the Yellow RCA jack to the backup camera input (if applicable).

Note: This RCA jack is used to retain the backup camera as well as the

LaneWatch camera.

• Connect the RCA jacks to the audio AUX-IN jacks (if applicable).White Red and

• If the vehicle is equipped with a factory amp, connect the White RCA jack to the

subwoofer output jack.

(d) 12-pin pre-wired ASWC-1 harness:

• This harness is to be used in along with the optional ASWC-1 (not included)

to retain steering wheel audio controls. If the ASWC-1 is not being used,

disregard this harness. If it will be used, please refer to the ASWC-1

instructions for radio connections and programming.

Note: Disregard the harness that comes with the ASWC-1.

Installing the HDCC-02

With the key in the off position:

• Connect the 22-pin connector of the HDCC-02 harness, into the

HDDC-02 interface.

• Connect the (2) 24-pin, 12-pin, 8-pin and 20-pin connectors of the HDCC-02

harness into the vehicle.

Connections to be made

HDCC-02

Initializing the HDCC-02

LaneWatch settings:

Note: The LaneWatch button is located on the left side of the steering wheel,

on the stalk.

• Press and hold the LaneWatch button for 15 seconds to toggle right turn signal

triggering on or off. If on, press and hold the button again for 15 seconds to

toggle it off. Likewise if off. The hi-beam indicator will flash 1 time if off; 2 times

if on.

Note: Right turn signal triggering is default on.

CAUTION! The following step should only be performed by an authorized

Honda technician. Once this procedure has been started, you cannot back

out of it.

• Press and hold the LaneWatch button for 50 seconds to begin the LaneWatch

aiming procedure. The hi-beam indicator will flash 3 times. At this point

the display will also show an image of the LaneWatch camera feed, with

instructions on what to do--a Honda authorized technician will know what to do

from here.

Note: While accessing LaneWatch aiming the right turn signal triggering will be

toggled after 15 seconds has passed, so the hi-beam indicator will flash

before the

50 second mark is reached. The technician will have to ignore that and continue

holding the button until the 50 second mark is reached to aim the camera

Clock and date settings:

This section refers to the buttons on the left side of the steering wheel.Note:

If no button is pressed for 15 seconds, this process will end.Note:

• Activate the analog clock on the top screen.

• Press and hold the “Source” button for 15 seconds until the hi-beam indicator

blinks twice, and then let go.

• Press and release the “Seek-Up” and “Seek-Down” buttons to toggle between

minutes, hours, days, months, and year.

• Once a choice is selected, press and release the “Volume-Up” or “Volume-

Down” buttons to adjust the settings.

• While changing the hour, press the “Source” button to toggle between 12 and

24 hour formats.

• Wait 15 seconds for the process to end.

Extra settings

Attention! If the interface loses power for any reason, the following steps will

need to be performed again. Also, if installing an ASWC-1 connect it after you

initialize and test the interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the

radio comes on.

Note:

If the radio does not come on within 60 seconds, turn the key to the

off position, disconnect the interface, check all connections, reconnect the

interface, and then try again.

• Turn the key to the off position, and then to the accessory position. Test all

functions of the installation for proper operation, before reassembling the dash.

Produktspecifikationer

Varumärke:	Axxess
Kategori:	Inte kategoriserad
Modell:	HDCC-02

Behöver du hjälp?

Om du behöver hjälp med Axxess HDCC-02 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Axxess Manualer

Axxess AX-MLOC-HD1 Bruksanvisning

26 September 2024

Axxess AXI-RGB1 Bruksanvisning

19 September 2024

Axxess AFSI-01 Bruksanvisning

19 September 2024

Axxess GMRSAV Bruksanvisning

19 September 2024

Axxess LC-BMRC-01 Bruksanvisning

19 September 2024

Axxess AX-TOYCAM3 Bruksanvisning

19 September 2024

Axxess AX-MITSUCAM Bruksanvisning

19 September 2024

Axxess AX-TOYRSAV Bruksanvisning

19 September 2024

Axxess HDCC-02 Bruksanvisning

19 September 2024

Axxess AX-TOYCAM2 Bruksanvisning

19 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024