Beltronics GT-360 Bruksanvisning

Läs nedan 📖 manual på svenska för Beltronics GT-360 (10 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/10
Programming
Press BRT to go from Press VOLUME + orto change
one category to the next your setting within a category
User Mode Access and customize all Settings and Preferences
Advanced*
Novice Access and customize units and display color, (all other
Settings are set to factory defaults)
NOTE: Switch back to Advance mode to view all Preferences
Pilot Scan Bar* Scanning Bar with Full Word
Full Word Full Word: AutoScan, Auto NoX, or Highway
Display Color Set color to match your vehicles dash displayCopper*/Blue/Green/Red
Speed Display Displays current speedOn*
O Displays battery voltage
Cruise Alert Oers double beep alert tones below specied speedO/ 20-160 mph
20 mph*
Over Speed Reminds you when you exceed a specied speedO / 20-160 mph
70 mph*
Meter Mode Single band with front and rear signal strength bar graphsStandard*
Tech Single band with numeric frequency and front and rear
signal strength bar graphs
Basic Simple messages replace bands:
Caution (if traveling below cruise alert limit)
Slow Down (if traveling above cruise alert limit)
Tones Standard* Standard Beltronics alert tones
Mild Mild doorbell chime alert tones
AutoMute Low/Med*/High/O
Automatically reduces audio to preferred volume during alert
AutoLock On* / O Automatically stores and locks out false alarms
Units English*/Metric Units for distance and speed
Language English*/Espanol Language for voice and text
Voice On* / O Voice announcements
GPS Filter Enables GPS-powered featuresOn* / O
Press and hold the BRT and SEN buttons to access Programming. To exit Programming, simply wait a few
seconds without pressing a button. The unit will display to conrm your selections.
Completed
7
AutoPower O Power turns on or odepending on your vehicle’s ignition
type (constant power or switched)
1 Hour Powers oautomatically after 1 hour
2 Hours Powers o automatically after 2 hours
4 Hours* Powers o automatically after 4 hours
8 Hours Powers o automatically after 8 hours
NOTE: If AutoPower is on, to save screen life the display screen goes
blank after 30 minutes without moving.
Band Enables Default SettingsDefault*
Modied Band Enables have been modied from their default settings
Press SEN to go from one Press VOLUME + orto change
band category to the next your setting within a category
X Band On* / O
K Band Freq: 24.050-24.250 GHz On* / O
NOTE: When K Band is o, you can select separate segments of the
band to turn on or o.
KN1 On* / O Freq: 24.050 - 24.110 GHz
KN2 On* / O Freq: 24.110 - 24.175 GHz
KN3 On* / O Freq: 24.175 - 24.250 GHz
KN4 On / O* Freq: 23.950 - 24.050 GHz
Ka Band Freq: 33.400-36.000 GHzOn* / O
NOTE: When Ka Band is o, you can select separate segments of the band to turn
on or o.
KaN1 On / O* Freq: 33.400 - 33.700 GHz KaN6 On / O*
Freq: 34.800 - 35.160 GHz
KaN2 On / O* Freq: 33.700 - 33.900 GHz KaN7 On / O*
Freq: 35.160 - 35.400 GHz
KaN3 On* / O Freq: 33.900 - 34.200 GHz KaN8 On* / O
Freq: 35.400 - 35.600 GHz
KaN4 On* / O Freq: 34.200 - 34.600 GHz KaN9 On / O*
Freq: 35.600 - 35.840 GHz
KaN5 On* / O Freq: 34.600 - 34.800 GHz KaN10 On / O*
Freq: 35.840 - 36.000 GHz
Ka Band On* / O
Ka-POP On / O*
Laser On* / O
TSR On* / O Automatically rejects trac ow sensors-monitoring false alarms
Marker Enable Default SettingsOn* / O
Modied Marker Enables have been modied from their default settings
NOTE:
AutoPower only
works with constant
power ignition
8
9
Press SEN to go from one Press VOLUME + or – to change
marker category to the next your setting within a category
Other On* / O Other location
Redlight On* / O Red light camera
Red & Speed Red light & speed cameraOn* / O
Speed Cam Speed cameraOn* / O
Air Patrol Known aircraft patrolled areasOn / O*
NOTE: User cannot mark an air patrol location
Speed Trap On* / O Speed trap
Air Patrol Known aircraft patroled areas On / O*
NOTE: User cannot mark an Air Patrol location
Clear Locations Clear all user Marked locations. Press SEN button to conrm
Marked
Lockouts Clear all lockouts. Press SEN button to conrm
Defender Clear all DEFENDER data. Press SEN button to conrm
Format Clear DEFENDER database, all markers, and all lockouts.
Press SEN button to conrm
*Default Setting

Produktspecifikationer

Varumärke: Beltronics
Kategori: Inte kategoriserad
Modell: GT-360

Behöver du hjälp?

Om du behöver hjälp med Beltronics GT-360 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Beltronics Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer