Benro Video Monopod A48FDS4 Bruksanvisning

Benro Stativ Video Monopod A48FDS4

Läs nedan 📖 manual på svenska för Benro Video Monopod A48FDS4 (2 sidor) i kategorin Stativ. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
Classic Series Monopods
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years of
dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
SETUP
Head Mounting (FIGURES 1 & 2)
If your Monopod did not come with a Head,
select one of the fine Benro Ballheads or
Tilthead that match your size Monopod
and install by screwing the Head clockwise
onto the 3/8" Mounting Thread of the Top
Plate. Once it is hand tight, secure by fully
tightening the Head Locking Screw(s) (on
select models) from below.
Most Heads have a 3/8" Base Mount so your
Benro Monopod is shipped with the 3/8
Mounting Thread exposed, but if the Head
you choose uses a 1/4–20 you can attach it
by simply reversing the Mounting Screw.
To do this turn the Locking Nut counter-
clockwise (using the supplied Wrench)
until it becomes loose, and unscrew the
Mounting Screw until it can be completely
removed. Reverse the Screw, so that the
threads are in position and screw it back
into place, secure with the Locking Nut
using the wrench.
NOTE: Allow enough of the screw threads
to be available for maximum security when
the Head is mounted onto the Monopod.
It’s recommended that at least 5 to 6
threads be exposed before locking the
Mounting Screw in place.
OPERATION
Before using your Monopod, adjust each
Leg Section to the desired height.
Make sure that the Monopod is firmly resting
on a stable surface and mount your camera
securely on the Monopod Head. Always
engage any safety locks on the Monopod
Head to prevent any accidental dismounting.
FOR BEST RESULTS: Do not raise the
Monopod higher than necessary and extend
the largest diameter Leg Sections first.
NOTE: Never carry your Monopod with
camera gear attached.
Leg Section Adjustment (FIGURES 3 & 4)
Each Leg Section can be adjusted to the
desired length by opening the Flip Lock
Lever so the Leg is free to slide in or out.
Once the desired length is achieved, snap
the Flip Lock Lever closed so that the leg
section is securely locked. Repeat this step
for each Leg Section until the Monopod is
set to the desired height.
NOTE: To prevent any accidental damage
to your gear, always remove any mounted
equipment (camera, etc.) from the Monopod
before adjusting the Leg Sections.
User Adjustments (FIGURE 5)
Flip Lock Lever tension is adjusted using the
3mm Allen Key plus the special Six-sided
Socket Wrench built into the plastic clip
which comes attached to the monopod leg.
USER NOTICE
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that Leg and Head Locks
are tightly engaged before mounting any
gear on your Monopod.
• Always clean and dry any Monopod after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Monopod is
not recommended for use in salt water.
If required, clean Monopod using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand
from all Leg Locks, Leg Sections and all
moving parts.
• Do not leave any Monopod in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Monopod or Tripod
unattended in areas where people could
trip over the equipment and get hurt.
• Remove camera, lens, and all gear from
the Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
Top Plate
Flip Lock Lever
Closed Cell Foam Grip
Wrist Strap
Rotating Pod Foot
Locking Nut
1/4-20 + 3/8
Mounting Screw
Wrench
21
Unlock Lock
3 4
3mm Allen Key
6-sided Socket
Wrench Clip
5
Operating Instructions & User Notice

Produktspecifikationer

Varumärke: Benro
Kategori: Stativ
Modell: Video Monopod A48FDS4

Behöver du hjälp?

Om du behöver hjälp med Benro Video Monopod A48FDS4 ställ en fråga nedan och andra användare kommer att svara dig


Stativ Benro Manualer

Benro

Benro S4 Pro Bruksanvisning

8 December 2024
Benro

Benro S8Pro Bruksanvisning

8 December 2024
Benro

Benro S2Pro Bruksanvisning

8 December 2024
Benro

Benro ITrip FIT19AIH0 Bruksanvisning

8 Oktober 2024
Benro

Benro BV4PRO Bruksanvisning

3 Oktober 2024
Benro

Benro KH25N Bruksanvisning

20 September 2024
Benro

Benro Video Monopod A48FDS4 Bruksanvisning

8 September 2024
Benro

Benro HD3A Bruksanvisning

4 September 2024
Benro

Benro C2573FS4 Bruksanvisning

1 September 2024
Benro

Benro TSL08CN00 Bruksanvisning

21 Augusti 2024

Stativ Manualer

Nyaste Stativ Manualer

3 Legged Thing

3 Legged Thing Albert 2.0 Bruksanvisning

15 Januari 2025
3 Legged Thing

3 Legged Thing AirHed Pro Bruksanvisning

15 Januari 2025
3 Legged Thing

3 Legged Thing Leo 2.0 Bruksanvisning

15 Januari 2025
3 Legged Thing

3 Legged Thing Ray Bruksanvisning

15 Januari 2025
Pyle

Pyle PSTND25 Bruksanvisning

13 Januari 2025
Bauhn

Bauhn ABSS-1224 Bruksanvisning

8 Januari 2025
Auray

Auray GNCL-12 Bruksanvisning

6 Januari 2025
Auray

Auray GNCL-20 Bruksanvisning

5 Januari 2025
Auray

Auray STBAR-9 Bruksanvisning

5 Januari 2025
Auray

Auray CLHD-3 Bruksanvisning

5 Januari 2025