Blebox shutterBox Bruksanvisning

Blebox Inte kategoriserad shutterBox

Läs nedan 📖 manual på svenska för Blebox shutterBox (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

SAFETY RULES

Connect only in accordance with the diagram presented in the

manual. Improper connections may be dangerous, it can damage

the controller, and loss of the warranty.

Do not connect the device to loads exceeding the permitted

values.

The installation of the device to a power mains that does not

meet the quality requirements dened by PN-EN 50160, will

result in the loss of the warranty

DANGER! Risk of electric shock! Even with the device turned o,

the outputs may be live. All assembly work should be ALWAYS

performed with the disconnected power circuit.

Test the controller’s work by clicking on the arrow near to the area showing

the window. If the electric shutter is moving in a dierent direction than you

suppose, go to Settings ("Settings" button at the top-right corner of the

screen) and select "Enable" in the "Move direction swap" option. Remember to

save your settings by clicking the "save" button, then go to the main panel by

clicking the arrow at the top-left corner of the screen. Check again whether

the shutter moves as expected.

If you have connected the wall push-button, check its work. Single pressing of

the "down" button / "up" button, will cause that the roller shutters moves in

the desired direction to the end position. If the electric shutter goes in the

opposite direction to the expected, select "enable" in the "Inputs swap"

option. When the electric shutter is moving, pressing any of the wall switches

causes that the shutter will stop immediately.

The next step is to select the type of electric shutter controlled - in settings,

in the "control type" select the option "roller shutter" when your shutter has

mechanical limit switches (manually adjustable with a key) or "without

positioning" when the electric shutter has electronic control system

(e.g. soft-start / overload protection / electronic limit switch, etc.). Specify also

the time the blind needs to move between the limit switches positions - this is

the time at which the controller provides voltage to the electric shutter motor

(it is not advisable to disable the move timeout).

If the controlled electric shutter have a mechanical limit switch, is possible the

control to a certain point. To use this feature, calibrate the controller by

clicking the "auto calibration" button. Once the procedure is conrmed, the

electric shutter will open to the upper limit switch position, then will close to

the lower limit switch position and then will open again to the upper limit

switch position. During the calibration, do not perform any action. To check

the work of the control to a certain point, go to the main panel by clicking the

arrow at the top-left corner and then by moving the nger several times over

the area showing the window in extreme and intermediate positions, verify if

the electric shutter moves to the selected position in the animation. You can

also set your electric shutter position - to do this, set the electric shutter in the

desired position and then hold the heart icon for about 5 seconds. Then verify

the functionality - moving the electric shutter to another position, then click

on the heart icon. The electric shutter should be placed in your favorite

position.

TAKE CARE ABOUT THE SAFETY AND COMFORT OF YOUR FAMILY – OPEN AND CLOSE

THE ELECTRIC SHUTTER STRAIGHTWAY FROM YOUR MOBILE PHONE

User manual

Disconnect theinstallation supply voltage before installing the controller.

Remember that any mounting works should be carried out when the mains

voltage is disconnected (switch o the mains fuse or disconnect the power

cord from the mains socket).

The controller should be installed in a place protected against adverse

environmental conditions, protected from third party access - in the ush box

or inside the enclosure of the controlled device. Remember that metallic

elements (wires, housing parts) have a negative inuence on the range of the

device, and consequently the comfort of use. It is recommended that the

device be mounted in a stable and xed position. Due to the operating

voltage of the device it is necessary that the connectors of the controller be

protected against accidental contacts or short circuits, which could cause

electric shock or damage to the device.

Read the diagram and then proceed to install the controller. Pay particular

attention to the designation of the controller connectors. Start with power

wires - phase L (usuallybrown) and neutral N (blue). Then, connect the load. If

you only want a local control with a wall switch, connect the wall push-button

according to the diagram. To control using only your phone or Tablet, it is not

necessary to install the wall push-button.

The controller supports all types of double monostable push-button. The

order of connection of the S1 / S2 input, to the right / left push-button does

not matter at the installation stage - it can be set at a later stage of the

controller conguration.

1INSTALLATION - BASICS

Unlock your phone or tablet and download the free wBox application. If you

have an Android mobile device, you will nd the application in the Play Store.

For iOS devices the application is in the App Store. For phones with Windows

Phone, you can download the application from the Windows Phone Store.

By using your mobile phone or tablet, connect it to the device wireless

network. To do this, enter to your smartphone or tablet settings, then go to

setting of the WiFi network and nd the network name „shutterBox-

-xxxxxxxxxx” where xxxxxxxxxx is the serial number of the device. Connect to

this network.

Turn on the wBox application. A device will appear at the top of the screen. To

add it to the application, click on "plus" on the right side of the name. To

pre-congure the controller, click on the default device name.

2 FIRST START

You can also set the conguration using the web browser

of your phone / tablet. After connecting to the wireless

network of the controller, turn on the browser and go to:

http://192.168.4.1

After making sure that the device is connected in accordance with the

diagram and that there are no metal components near the controller which

may accidentally cause short-circuit, start the device by turning on the power

(turning on the mains fuse or connecting the power cord to the power outlet).

electric shutter controller

with μWiFi technology

sb101

CONNECTION DIAGRAM

electric shutter

button

3ACCESS POINT AND WIFI NETWORK SETTINGS

Once you turn on the controller for the rst time, you can proceed to its

further conguration. Being connected to the WiFi network emitted by the

device, in the control panel of the wBox application select the device, then go

to “settings” (button at the top-right corner of the screen).

You can change the name of the device that is displayed in the wBox

application. In addition, you can change the name and password of its

generated WiFi network. Remember that changing the network name or

password will disconnect the device immediately after you click the "save"

button, so re-connect to the device using the newly assigned network name

and password.

You can add the controller to your home WiFi network to control it through

this home network or from anywhere in the World. To do this, in the "Connect"

settings section, select a network name from the list and press "Connect". If is

required, enter the WiFi network password. During the connection of the

controller to your home network, the phone / tablet may disconnected from

the network. In this case, you will need to reconnect your phone / tablet to the

controller network.

Please remember that in order to control the device outside the local WiFi

network, from anyplace in the World by using the wBox application, the

option "Remote access enabled" in the controller settings must be set to "yes".

Once you've nished conguring the WiFi network, you can disconnect your

phone/tablet from the controller network and connect your mobile device

directly to your home WiFi network. The control from the wBox application

will work the same way as when the phone / tablet is connected to the

controller network. If the user leaves the local network, for example, leaving

home or using the mobile data, the wBox application will signal this state as

"remote mode". In this case, the devices can be controlled, but for security

reasons settings are not available.

made of polyurethane composition not

containing halogens, self-extinguishing for

thermal class B (130 °C)

Supply voltage 230V

Maximum current (total) 5A

5AMaximum current (channel)

Max load 1000W

Inputs number 2

Input type logical, to L

Inputs voltage 230V

Galvanic isolation No

Housing

Power consumption

Outputs number

Output type

less than 1W

relay

bi-directional, encrypted

direct connection (as Access Point), Wi-Fi

connection via a standard router,

connection with access from any location

in the World (requires only access to the

Internet)

Apple iPhone, Apple iPad, iPad Mini,

Android, Windows Phone, computers and

mobile devices operating a fully HTML5,

Apple watch support coming soon

Protection rating IP20

Transmission frequency 2.4GHz

μWiFi, compatible with WiFi, 802.11gCommunication standard

Communication mode

Control with

Dimensions

Transmission

40 x 48 x 20 mm

TECHNICAL SPECIFICATIONS

For more information visit our website

www.blebox.eu

Or send us an email to: info@blebox.eu

Support is available at support@blebox.eu

ADDITIONAL INFORMATION

SOFTWARE UPDATE

LOCATION AND TIME OF THE DEVICE,

SCHEDULE

To update the software in the controller, connect it to your home WiFi network

(see "Access Point and WiFi settings" section) which is connected to the

Internet. Go to “settings” (button at the top-right corner of the screen) and

click the "get new rmware" button in the nal section on settings. Wait about

1 minute, do not close the interface and don’t perform other actions. The

device will download the latest software. The software version number,

hardware version and device identier can be read at the bottom of the

settings screen.

The controller has the ability to work according to a given schedule. To make

this possible, set the device's time. Go to settings in the "device time" section,

click "change timezone". Then select your region and location from the list,

conrm your selection clicking the "save" button. The device will synchronize

its time with the server time (if the controller is in a WiFi network with access

to Internet) or it will download time from the phone / tablet. It is recommen-

ded that the controller is always connected to a WiFi network with Internet

access so that it can automatically synchronize its clock.

To be able to control devices using the local sunrise and sunset, you must also

select the location of the controller. You can specify the location of the device

using a smartphone or tablet. In the section "device location", click "set

locations". Browser will ask whether to share locations - allow. In the "coordina-

tes" eld,should appear the approximate coordinates of your location. If the

"set locations" button blinks red with the word "error", or the "coordinates"

eld did not change the value from "not set" to numeric data, a failurehas

occurred during the location download. You should make sure that the phone

/ tablet has a GPS module and that the sharinglocation service is enabled on

the phone.

Adding schedule entries can be performed by clicking the "add item" button

in the "schedule" section of settings. You can select the days in which the task

will be performed, the type of entry (at a specic time, or relative to sunrise /

sunset - only having a correctly set location) and set the parameters of the

task. The set tasks will be visible as a list, individual entries can be edited or

deleted.

Produktspecifikationer

Varumärke:	Blebox
Kategori:	Inte kategoriserad
Modell:	shutterBox

Behöver du hjälp?

Om du behöver hjälp med Blebox shutterBox ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Blebox Manualer

Blebox gateBox Bruksanvisning

18 September 2024

Blebox shutterBox Bruksanvisning

18 September 2024

Blebox parkingsensor Bruksanvisning

18 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024