Bobrick B-164 Bruksanvisning
Läs nedan 📖 manual på svenska för Bobrick B-164 (3 sidor) i kategorin Spiegel. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/3
Mark the location of the mounting holes. See individual product
specications on page two for mounting hole locations.
1.
PARTS/TOOLS NEEDED:
Backlit Mirror Mounting Hardware Electric Drill Wiring Kit
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
Read all instructions before using this mirror.
MIRRORS SHOULD ONLY BE INSTALLED USING THE FOLLOWING INSTRUCTIONS. FAILURE TO
FOLLOW THESE INSTRUCTIONS WILL VOID THE WARRANTY.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons:
• Unplug power before putting on or taking off parts.
• Close supervision is necessary when this mirror is used by, or near children, invalids, or disabled persons.
• Use this mirror only for its intended use as described in these instructions. Do not use attachments not recommended by Bobrick.
• Never operate this mirror if it has a damaged cord, if it is not working properly, if it has been dropped or damaged, or dropped
into water. Contact Bobrick for a replacement mirror.
• Keep the cord away from heated surfaces.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Exposing the mirror edges to liquids may cause a permanent discoloration to the mirror etching that is NOT covered by Bobrick warranty.
• Risk of electric shock - Connect this mirror to a properly grounded outlet only. See grounding instructions. WARNING:
CLEANING INSTRUCTIONS
• Clean mirrors with warm water and a soft, lint free cloth, do not allow liquids to seep under the edges. Don’t use abrasive,
acid or alkali cleaners or products with ammonia or vinegar.
• Apply mild cleaners directly to a cloth, do not spray directly on the mirror. Applying liquids directly to the mirror’s surface may allow the
liquid to seep/wick between the layers on the edge of the mirror. If this occurs there may be a permanent discoloration on the mirror
etching which is NOT covered by Bobrick warranty.
• Dry mirror immediately following cleaning and make sure all joints and edges are dry.
ADA requires that “Mirrors shall be mounted with the bottom edge of the
reecting surface no higher than 40 in (1015mm) above the nished oor
1.”
For lit mirrors this means the dimension is to the inner most edge of the lit portion.
40"
Finished oor
INSTRUCTIONS FOR INSTALLATION
BOBRICK MODEL B-164 BACKLIT MIRROR
Install included #14 round slotted wood mounting screws
into pre-marked holes. Note, all mirrors must be installed in
contractor supplied blocking.
Slide the mirror assembly onto the screws.
2. Ensure screw sits all the way
at the top of the keyhole slot
Dimensional drawings
3.
18.9”
1.8”
11.4”
0.8”
12.3”
22”
34”
5.2”
5.2”
7.2”
18.9”
40”
22”
1.8”
11.4”
0.8”
5.2”
5.2”
15.3”
7.2”
Punch out one of the three holes on the power supply box and bring in incoming AC power wires to the box. Utilize the provided Romex
connectors and following the wiring diagram below. Please note, the lighting will be make all connections inside the power supply box
pre-wired to the mirror.
4. Wiring & Grounding Instructions
Load (+)
PUNCH ONE OF THE
THREE LARGE HOLES
Remove nut, place ground
wiring and screw nut back on.
Neutral (-)
AC 120-277V POWER
24” X 36” 24” X 42”
Note, the mirrors come with an additional 90˚ three prong plug for NEUTRAL (-)
(BLACK)
LOAD (+)
(WHITE)
GROUND
(GREEN)
Note, the mirrors come with an additional 30° three prong plug for plug-in
installations.
© 2020 by Bobrick Washroom Equipment, Inc.
Form No. 164-69 rev. 9/29/20
In the United States: BOBRICK WASHROOM EQUIPMENT, INC.
200 Commerce Drive, Clifton Park, NY 12065-1350 • Telephone: (518) 877-7444 • FAX: 518-877-5029
6901 Tujunga Ave., North Hollywood, CA 91605-5882 • Telephone:(818) 982-9600 • FAX: 818-503-1102
or email customerservice@bobrick.com
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1 • FAX: (877) 423-8555
PUNCH ONE OF THE
THREE LARGE HOLES
Punch out one of the three holes on the power supply box and bring in incoming dimming wires to the box. Utilize the provided Romex
connectors and following the wiring diagram below.make all connections inside the power supply box
OPTIONAL: Dimming Wiring Instructions
TROUBLESHOOTING
The mirror doesn’t light:
A. Check the connection between the mirror and buildings wiring.
B. Verify that there is power coming out of the power supply.
C. Verify that there is 120V power coming out of the buildings junction box.
D. Verify that the tape light has not been unplugged from the power supply.
Load (+)
Remove nut, place ground
wiring and screw nut back on.
Neutral (-)
AC 120-277V POWER
Positive (+)
Negative (-)
Dimmer
DIM (+)
DIM (-)
Produktspecifikationer
| Varumärke: | Bobrick |
| Kategori: | Spiegel |
| Modell: | B-164 |
Behöver du hjälp?
Om du behöver hjälp med Bobrick B-164 ställ en fråga nedan och andra användare kommer att svara dig
Spiegel Bobrick Manualer
12 September 2024
12 September 2024
12 September 2024
12 September 2024
Spiegel Manualer
- Spiegel IKEA
- Spiegel Philips
- Spiegel Orbegozo
- Spiegel Jysk
- Spiegel Miomare
- Spiegel Beurer
- Spiegel BaByliss
- Spiegel Scarlett
- Spiegel Sencor
- Spiegel Lanaform
- Spiegel Conair
- Spiegel Livarno
- Spiegel Rotel
- Spiegel Valera
- Spiegel Revlon
- Spiegel Sanexo
- Spiegel V-Tac
- Spiegel Personal Care
- Spiegel Fenomé
- Spiegel Beautifly
- Spiegel Viidako
- Spiegel Kristall Form
- Spiegel Coaster
Nyaste Spiegel Manualer
26 Oktober 2024
6 Oktober 2024
3 Oktober 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024