Bogen NQ-E7020 Bruksanvisning

Bogen Kontroller NQ-E7020

Läs nedan 📖 manual på svenska för Bogen NQ-E7020 (2 sidor) i kategorin Kontroller. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
NQ-E7020 Digital Call Switch
Application Manual
The NQ-E7020 is a single gang-box style wall mounted
push-button switch that allows users to initiate a normal,
urgent, or emergency call from staff locations via an
associated Nyquist intercom speaker.
The switch uses a capacitive touch button interface. A color
LED ring is used to conrm user actions and to indicate
status (for example, changing color and/or state from
solid color to blinking) or to acknowledge a button press when a user
initiates a call or when a call has been terminated. The LED status ring
is also used to indicate when Nyquist system’s call queue containing
the station’s call request is cleared or if the station’s call request is
individually cleared by the administrative station without responding.
Installation
The NQ-E7020 mounts into a standard single gang outlet box and is outtted with a standard deco-
ra plate (color based on the switch’s specic application and/or customer need).The back has four
screw-terminal connections (GND, CL, CH, 5V). These get connected to the matching terminals on
the CAN Bus source/master device using standard CAT5 cabling. Load resistance needs to be set
on the end-of-line DCS. Refer to Figure 1.
Figure 1
Publication Number 740-00075B 1811
CAN_H and CAN_L must be a twisted pair like CAT5 cabling.
CAN wiring can be daisy-chained.
All devices are internally terminated and the last switch on the bus must have the termination switch in the “ON” position.
5V and Signal Ground can be either twisted or not.
Signal Ground
CAN_L
CAN_H
5V
Digital Call Switch Digital Call SwitchApplicable
Appliance
Recommended CAT5
Cable Lengths
CAT5 cable lengths and the number of
CAT5 wire pairs determine the number
of digital call switches that can be dai-
sy-chained. (See Figure 2.)
Length limits are due to voltage drop
across the power conductors. For 2-pair
or 3-pair, it is best to tie the solids togeth-
er and to tie the stripes together at each
end of a long run. This will make it easier
to keep up with which wires are V+ and V-.
CAUTION:
These calculations are based on standard 24 AWG solid copper wire. Calculations will not be
accurate for copper-plated aluminum wire or wire guage less than 24 AWG.
Conguring
NOTE: Refer to the System Administrator Manual for detailed instructions on how to congure
the DCS. DCS conguration is part of setting System Parameters and Class of Service parame-
ters.
1200 MacArthur Blvd. Suite 304, Mahwah, NJ 07430 • 1-800-999-2809
© Copyright 2018, Bogen Communications, Inc.
Figure 2

Produktspecifikationer

Varumärke: Bogen
Kategori: Kontroller
Modell: NQ-E7020

Behöver du hjälp?

Om du behöver hjälp med Bogen NQ-E7020 ställ en fråga nedan och andra användare kommer att svara dig


Kontroller Bogen Manualer

Bogen

Bogen NQ-E7020 Bruksanvisning

15 Augusti 2024

Kontroller Manualer

Nyaste Kontroller Manualer

Sonance

Sonance VC60R Bruksanvisning

2 April 2025
Trust

Trust Mylox GXT 735G Bruksanvisning

30 Mars 2025
Trust

Trust Mylox GXT 735 Bruksanvisning

30 Mars 2025
American DJ

American DJ STAGE SETTER-8 Bruksanvisning

30 Mars 2025
American DJ

American DJ DP-DMX20L Bruksanvisning

30 Mars 2025
Visual Productions

Visual Productions TimeCore Bruksanvisning

30 Mars 2025
PCE Instruments

PCE Instruments PCE-RE22T Bruksanvisning

28 Mars 2025
Turtle Beach

Turtle Beach Recon Bruksanvisning

27 Mars 2025
Metronic

Metronic Zap 3 495383 Bruksanvisning

26 Mars 2025
Deltaco

Deltaco GAM-103 Bruksanvisning

2 Mars 2025