Broan NuTone Bruksanvisning

Broan övervakningskamera NuTone

Läs nedan 📖 manual på svenska för Broan NuTone (7 sidor) i kategorin övervakningskamera. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/7
MODEL LA542WH
Page 1
WIRELESS DOOR CHIME
Installation & Operating Instructions
IMPORTANT: This wireless pushbutton and chime set is for
residential use, only. It will operate at an unobstructed distance
of 300 feet. Building materials may reduce operating distance.
Certain building materials; such as, but not limited to metal,
concrete, brick, stucco and foil-lined insulation; cause greater
interference than others; for example, wood or vinyl siding.
INSTALL PUSHBUTTON BATTERY
Refer to Figures 1 and 2.
1. Remove pushbutton and 3V lithium coin-battery from packaging.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its base.
3. Orient battery with “+” side viewable.
4. Insert battery into holder and press to seat.
5. Insert top of mounting base onto pushbutton and press bottom
together until mounting base snaps securely onto pushbutton.
Use only 3V (volt) lithium CR2032 style coin-battery for replacement.
INSTALL CHIME BATTERIES
Refer to Figures 3 and 4.
1. Remove chime from packaging.
2. Use finger to depress tab and remove chime cover. Set cover aside.
3. Insert three (3) 1.5V “D” alkaline batteries (not supplied) oriented as
shown on front of battery compartment.
4. Replace chime cover.
Figure 1
“PUSH”
TO OPEN COVER
3V LITHIUM
CR2032-STYLE
COIN
BATTERY
Figure 2
SLOT
“LEARN” PROCEDURE
Refer to Figure 5.
1. Set pushbutton and chime next to each other.
2. Press and release “Learn” button on chime.
3. LED lights to indicate “Learn” mode was entered.
4. Press and release pushbutton.
5. Confirm chime-tone is heard.
6. Repeat Step 4 to cycle through available chime-tones.
7. When desired chime-tone is heard, press and release “Learn” button
(Note: Chime may not respond to this button being pressed if it is too
soon after chime-tone sounds).
8. LED should turn off to confirm “Learn” mode exited.
9. Press and release pushbutton and confirm chime-tone hasn’t change
from desired one.
• Up to four (4) pushbuttons can be used with a single chime by
selecting different chime-tones for each pushbutton.
• Chime can erase all “Learned” pushbuttons and tones by pressing
and holding “Learn” button; LED will light; within 20 seconds, LED will
turn off; release “Learn” button.
DETERMINE USABLE LOCATIONS
Do not plan to mount pushbutton directly on metal or concrete
surfaces; install a 1/8-1/4” wood spacer between pushbutton and
metal or concrete mounting surface.
Some stucco houses have metal mesh in the wall structure, which
will affect the wireless chime performance.
Experiment with various pushbutton and chime locations to
determine location that gives best performance before mounting
permanently.
Chime must not be located within 1-foot of any metal.
Pushbutton and chime should be located within 300-feet of each
other.
1. Place chime near desired mounting location.
2. Select a level location and hold pushbutton in desired mounting
location.
3. Press and release pushbutton.
4. Confirm chime-tone sounded.
5. If chime-tone does not sound, temporarily affix pushbutton to
mounting surface with double-stick or folded-over tape; repeat Steps 3
and 4.
6. If chime-tone still does not sound, move location of chime closer to
pushbutton; repeat Steps 3 and 4.
Figure 3 Figure 4
Figure 5
VOLUME BUTTON
LEARN BUTTON LED
MODEL LA542WH
Page 2
Figure 6
MOUNT PUSHBUTTON
Refer to Figures 1 and 6.
1. After selecting usable locations in previous section, go to pushbutton
location.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its mounting base.
3. Make sure pushbutton mounting location is level.
4. Position pushbutton mounting base with “TOP” arrow correctly
oriented and mark base mounting holes locations.
5. Drill two (2) holes, 1/16” diameter if using supplied screws alone or
3/16” diameter if using supplied plastic anchors and screws, at base
mounting hole locations.
6. If 3/16” diameter holes were drilled, insert supplied plastic anchors.
7. Secure pushbutton base to mounting location with two (2) supplied
screws.
8. Make sure black O-ring is completely seated in its mounting base
groove with round edge at top and flat edge at bottom.
9. Hook pushbutton top catch onto top of base, swing pushbutton into
position and press bottom of pushbutton until it securely snaps onto
base.
SET VOLUME PROCEDURE
Refer to Figure 5.
There are four (4) volume levels which are accessed sequentially.
1. Press and release pushbutton to sound chime tone.
2. Press and release “Volume” button to hear the next volume setting.
3. If chime tone is not sounding when “Volume” button is pressed then
chime will sound a beep to indicate volume setting.
4. Volume setting cycles from loud to medium-loud, medium-soft and soft
then back to loud.
5. Repeat Step 2 until desired volume level is set.
6. Last volume setting is remembered.
7. Press and release pushbutton to sound chime tone and confirm
desired volume setting.
BASE
PLASTIC
ANCHORS
TOP
BLACK
“O” RING
MOUNTING
SCREWS
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Regulatory Information
The user is cautioned that changes or modifications not expressly
approved by the party responsible for regulatory compliance
could void the user’s authority to operate this equipment.
MOUNT CHIME
Refer to Figure 7.
1. Go to selected chime location.
2. There are two ways to mount this chime
a. Back-plate permanently mounted to wall; or
b. Back-plate removable from wall.
Select desire back-plate mounting method.
3. Measure down from top of desired chime location and mark
mounting screw(s) position(s).
a. 1-1/8” and centered, and 3-3/8” down from first mark and 1-5/16”
either side of center; or
b. 7/8” and 1-5/16” either side of center.
4. Drill holes, 1/16” diameter if using supplied screws alone or 3/16”
diameter if using supplied plastic anchors and screws, at marked
mounting screw locations.
5. If 3/16” diameter holes were drilled, insert supplied plastic anchors.
6a. Place screw through back-plate centered hole and into mounting
hole and tighten until 1/8” remains protruding.
Place (2) screws through back-plate bottom holes and into mounting
holes and tighten until snug.
Tighten top screw until it is snug.
6b. Place screws into mounting holes and tighten until 1/8” remains
protruding.
Place back-plate keyhole slots over mounting screws and apply slight
downward force to seat keyhole slot on mounting screw.
7. Hook chime top to back-plate, swing chime bottom towards back-
plate and press on front-bottom of chime until chime is secured to
back-plate.
TROUBLESHOOTING GUIDE
1. Chime does not sound:
a. If pushbutton LED doesn’t light when pushbutton is pressed then:
1. Check battery polarity in pushbutton.
2. Replace battery in pushbutton.
b. Replace batteries in chime.
c. Bring pushbutton in area of chime and test:
1. If chime sounds then change location of chime.
2. If chime does not sound then conduct erase procedure per note
at end of “Learn” Procedure then conduct “Learn” Procedure,
Steps 1 through 9.
2. Chime loses volume or changes tone: Change batteries in chime.
3. Chime sounds when pushbutton is not pressed:
a. Release pushbutton catch at bottom and check inside for signs of
moisture; check O-ring for cracks or damage.
b. Conduct erase procedure per note at end of “Learn” Procedure then
conduct “Learn” Procedure, Steps 1 through 9.
Figure 7
1/8”
7/8”
MOUNTING
METHOD SHOWN:
Back-plate
removable from wall.
See 2. b. below.
MODÈLE LA542WH
Page 3
CARILLON DE PORTE SANS FIL
Directives d’installation et d’utilisation
IMPORTANT : Cet ensemble de bouton-poussoir et de carillon sans fil est conçu
uniquement pour un usage résidentiel. Il fonctionne jusqu’à une distance sans
obstruction d’au moins 91 mètres (300 pi). Des matériaux de construction peuvent
en réduire la portée. Certains matériaux de construction comme le métal, le
béton, la brique, le stucco et l’isolant couvert de papier aluminium causent plus
d’interférences que d’autres comme le parement de bois ou de vinyle.
INSTALLATION DE LA PILE DU BOUTON-POUSSOIR
Voir les figures 1 et 2.
1. Sortez de l’emballage le bouton-poussoir et la pile bouton de 3V aulithium.
2. Insérez un petit tournevis plat au bas du bouton-poussoir et tournez-le pour en
séparer la base.
3. Placez la pile avec le côté « + » visible.
4. Insérez la pile dans son logement et pressez pour l’appuyer.
5. Insérez la base dans le bouton-poussoir et pressez les deux parties ensemble
pour bien les emboîter.
N’utilisez qu’une pile bouton de 3V (volts) au lithium CR2032 comme pile
deremplacement.
INSTALLATION DES PILES DU CARILLON
Voir les figures 3 et 4.
1. Sortez le carillon de l’emballage.
2. Avec le doigt, appuyez sur l’ergot et retirez le couvercle du carillon. Mettez le
couvercle de côté.
3. Insérez trois (3) piles alcalines « D » de 1,5 V (non comprises) dans le sens
indiqué à l’avant du compartiment à piles.
4. Replacez le couvercle.
Figure 1
« POUSSER »
POUR OUVRIR LE
COUVERCLE
PILE BOUTON
AU LITHIUM
CR2032 3V
Figure 2
FENTE
PROCÉDURE D’« APPRENTISSAGE »
Voir la figure 5.
1. Placez le bouton-poussoir et le carillon l’un à côté de l’autre.
2. Appuyez sur le bouton « Apprendre » sur le carillon puis relâchez-le.
3. La DEL s’allume pour indiquer que vous êtes entré en mode « Apprentissage ».
4. Appuyez sur le bouton-poussoir et relâchez-le.
5. Confirmez que vous avez bien entendu le carillon.
6. Répétez l’étape 4 pour passer entre les tonalités du carillon.
7. Lorsque vous entendez le type de carillon souhaité, appuyez sur le bouton
« Apprendre ». (Remarque : le carillon risque de ne pas réagir si vous appuyez
trop tôt sur ce bouton après que le carillon ait résonné).
8. La DEL devrait s’éteindre pour confirmer que vous avez quitté le mode
« Apprentissage ».
9. Appuyez sur le bouton-poussoir et relâchez-le pour vérifier que la tonalité du
carillon n’a pas changé.
• Vous pouvez utiliser jusqu’à quatre (4) boutons-poussoirs avec le même carillon
en choisissant des tonalités différentes pour chacun.
• Le carillon peut effacer tous les boutons-poussoirs et tonalités « appris » si vous
maintenez appuyé le bouton « Apprendre »; la DEL s’allume alors; après environ
20 secondes la DEL s’éteint; relâchez alors le bouton « Apprendre ».
CHOIX DES EMPLACEMENTS UTILISABLES
Ne fixez pas le bouton-poussoir directement sur une surface en métal ou en
béton; installez une petite cale en bois de 3,2 à 6,4 mm (1/8 à 1/4 po) entre le
bouton et la surface métallique ou en béton.
Certaines maisons à revêtement en stucco ont un treillis métallique dans
leur charpente, ce qui nuira au fonctionnement du carillon.
Essayez divers emplacements pour le bouton-poussoir et le carillon pour
déterminer le meilleur endroit possible avant de les fixer en permanence.
Le carillon ne doit pas être situé à moins de 30,5 cm (1 pi) de toute surface
métallique.
Le bouton-poussoir et le carillon ne doivent pas être séparés de plus de
91mètres (300 pi) l’un de l’autre.
1. Placez le carillon près de l’endroit où il sera fixé.
2. Choisissez un endroit de niveau et tenez le bouton-poussoir à
l’emplacementvoulu.
3. Appuyez sur le bouton-poussoir et relâchez-le.
4. Vérifiez que le carillon a bien sonné.
5. Si le carillon ne sonne pas, fixez temporairement le bouton-poussoir à la surface de
montage avec du ruban double face ou un ruban replié; répétez les étapes 3 et 4.
6. Si le carillon ne sonne toujours pas, rapprochez le carillon du bouton-poussoir;
répétez les étapes 3 et 4.
Figure 3 Figure 4
Figure 5
BOUTON DE
VOLUME
BOUTON
APPRENDRE DEL

Produktspecifikationer

Varumärke: Broan
Kategori: övervakningskamera
Modell: NuTone

Behöver du hjälp?

Om du behöver hjälp med Broan NuTone ställ en fråga nedan och andra användare kommer att svara dig


övervakningskamera Broan Manualer

Broan

Broan NuTone Bruksanvisning

27 Augusti 2024

övervakningskamera Manualer

Nyaste övervakningskamera Manualer

Philips

Philips B120E Bruksanvisning

16 Januari 2025
Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Bruksanvisning

10 Januari 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Bruksanvisning

8 Januari 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Bruksanvisning

8 Januari 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Bruksanvisning

8 Januari 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Bruksanvisning

8 Januari 2025
Speco Technologies

Speco Technologies O5LB1 Bruksanvisning

8 Januari 2025
ZKTeco

ZKTeco AntarVis 2.0 Bruksanvisning

8 Januari 2025
Speco Technologies

Speco Technologies O2P30X Bruksanvisning

8 Januari 2025
TP Link

TP Link InSight S345ZI Bruksanvisning

8 Januari 2025