Brother P-touch PT-P750W Bruksanvisning

Brother Etikettskrivare P-touch PT-P750W

Läs nedan 📖 manual på svenska för Brother P-touch PT-P750W (4 sidor) i kategorin Etikettskrivare. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

Follow these guidelines to avoid the risk of fire, burns, injury, electric

shocks, rupture, overheating, abnormal odors or smoke.

• Always use the specified voltage and the included AC adapter (AD-E001) for the

P-touch labeler to prevent any damage or failure.

• Do not touch the P-touch labeler during a lightning storm.

• Do not use the P-touch labeler/AC adapter in places of high humidity such as

bathrooms.

• Do not overload the power cord.

• Do not place heavy objects on, or damage the P-touch labeler, power cord or plug.

Do not forcibly bend or pull the power cord. Always hold the AC adapter when

disconnecting from the power outlet.

• Make sure that the plug is fully inserted in the power outlet. Do not use an outlet that

is loose.

• Do not allow the P-touch labeler/AC adapter/power plug/batteries to get wet, for

example, by handling them with wet hands or spilling beverages on to them.

• Do not disassemble or modify the P-touch labeler/AC adapter/batteries.

• Do not allow a metal object to contact both the plus and minus ends of a battery.

• Do not use sharp objects, such as tweezers or a metallic pen, to change the batteries.

• Do not throw the batteries into fire or expose to heat.

• Disconnect the AC adapter, remove batteries immediately and stop using the

P-touch labeler if you notice abnormal odor, heat, discoloration, deformation or

anything unusual while using or storing it.

• Do not use a damaged or leaking battery as the fluid may get on your hands.

• Do not use a deformed or leaking battery or one whose label is damaged. There is

a possibility of damaging the P-touch labeler.

• Since loss of eyesight may result if leaked fluid from batteries gets into your eyes,

immediately rinse your eyes with a large amount of clean water, and then seek

medical attention.

Follow these guidelines to avoid personal injury, liquid leakage, burns

or heat.

• When the P-touch labeler is not being used, store it out of the reach of children. In

addition, do not allow children to put any P-touch labeler parts or labels in their

mouths. If any object has been swallowed, seek medical attention.

• Do not touch metal parts around the print head immediately after printing.

• Do not touch the cutter blade. (See Unpacking the PT-P750W & Parts Description.)

• If leaked fluid from batteries gets on your skin or clothes, immediately rinse them

with clean water.

• Remove the batteries and disconnect the AC adapter if you do not intend to use the

P-touch labeler.

• Do not use any batteries other than those specified. Do not use combinations of old

and new batteries or combinations of different types, different charging levels,

different manufacturers or different models. Do not insert a battery with its plus and

minus ends reversed.

• Do not drop or hit the P-touch labeler/AC adapter.

• Do not put your finger inside the P-touch labeler when you close the cassette cover.

• Before using Ni-MH rechargeable batteries, carefully read the instructions for the

batteries and battery charger, and be sure to use them correctly.

• When using Ni-MH rechargeable batteries, charge the batteries with a specialized

battery charger before using the batteries.

• Do not put your finger inside the tape exit slot. You could be injured by the cutter blade.

• Depending on the location, material, and environmental conditions, the label may

unpeel or become irremovable, the color of the label may change or be transferred

to other objects. Before applying the label, check the environmental conditions and

the material.

• Do not use the P-touch labeler in any way or for any purpose not described in this

guide. Doing so may result in accidents or damage to the P-touch labeler.

• Use only Brother TZe tapes with the P-touch labeler. Do not use tapes that do not

have the mark.

• Only use a soft, dry cloth to clean the P-touch labeler; never use alcohol or other

organic solvents.

• Use a soft wipe to clean the print head; never touch the print head with your fingers.

• Do not put any foreign objects into the tape exit slot, the AC adapter connector or

battery compartment, etc.

• Do not place the P-touch labeler/batteries/AC adapter in direct sunlight or rain, near

heaters or other hot appliances, in any location exposed to extremely high or low

temperatures (e.g., on the dashboard or in the back of your car), high humidity, or

in dusty locations.

• Do not try to print if the cassette is empty; it will damage the print head.

• Do not pull the tape while printing or feeding; it will damage the tape and the P-touch

labeler.

• Any data stored in memory will be lost due to failure or repair of the P-touch labeler,

or if the batteries expire.

• The P-touch labeler is not equipped with a charging feature for rechargeable batteries.

• The length of the printed label may differ from the displayed label length on the

computer.

• A protective clear plastic sticker is placed over the top panel during manufacturing

and shipping. This sticker should be removed prior to use.

• When printing multiple copies of a label or using the numbering function printing, the

P-touch labeler will not detect the end of the tape cassette and will continue operating.

• When using Heat Shrink Tube, the printing area will be smaller than when using

normal tape.

• If you connect a mobile device to the P-touch labeler using the NFC function without

installing a specialized application, the Apps section of Google Play may be

displayed on your mobile device automatically.

You may be charged a communication fee for this service.

Open Source Licensing Remarks

This product includes open-source software.

To see the open source licensing remarks, please go to the manual download

selection on your model's home page of Brother Solutions Center at

http://support.brother.com/.

The available scientific evidence does not show that any health problems are associated with

using low power wireless devices. There is no proof, however, that these low power wireless

devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency

energy (RF) in the microwave range while being used. Whereas high levels of RF can produce

health effects (by heating tissue), exposure of low-level RF that does not produce heating

effects causes no known adverse health effects. Many studies of low-level RF exposures have

not found any biological effects. Some studies have suggested that some biological effects

might occur, but such findings have not been confirmed by additional research. PT-P750W has

been tested and found to comply with FCC radiation exposure limits set forth for an

uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.

Trademarks and Copyrights

BROTHER is either a trademark or a registered trademark of Brother Industries, Ltd.

P-TOUCH is a trademark or registered trademark of Brother Industries, Ltd.

Microsoft, Windows Vista, Windows Server and Windows are either registered

trademarks or trademarks of Microsoft Corp. in the United States and/or other countries.

Apple, Macintosh, Mac OS, iPhone, iPad and iPod are trademarks of Apple Inc.,

registered in the United States and other countries.

The names of other software or products used in this document are trademarks or

registered trademarks of the respective companies that developed them.

Wi-Fi and Wi-Fi Alliance are registered trademarks of the Wi-Fi Alliance.

Each company whose software title is mentioned in this manual has a Software

LicenseLicence Agreement specific to its proprietary programs.

Any trade names and product names of companies appearing on Brother products,

related documents and any other materials are all trademarks or registered trademarks

of those respective companies.

Safety Precautions

WARNING Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injuries.

CAUTION Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injuries.

General Precautions

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Federal Communications Commission (FCC) Declaration of

Conformity (For USA Only)

Responsible Party: Brother International Corporation

200 Crossing Boulevard

P.O. Box 6911

Bridgewater, NJ 08807-0911 USA

TEL : (908) 704-1700

Product Name : Brother P-touch Electronic Labeling System

Model Number : PT-P750W

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

PT-P750W is equipped with FCC ID:B3Q8VA652.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• This transmitter must not be co-located or operated in conjunction with any other

antenna or transmitter.

Important

• The enclosed interface cable should be used in order to ensure compliance with

the limits for a Class B digital device.

• Changes or modifications not expressly approved by Brother Industries, Ltd.

could void the user's authority to operate the equipment.

* In case WLAN Interface is in use.

CAUTION: To maintain compliance with FCC’s RF exposure guidelines, use only

the supplied antenna. Unauthorize antenna, modification, or attachments could

damage the transmitter and may violate FCC regulations.

ELECTRONIC LABELING SYSTEM

English

User’s Guide

Español

PT-P750W

Read this guide before you start using your P-touch labeler.

Keep this guide in a handy place for future reference.

LAE838001

The purpose of the International ENERGY STAR® Program is

to promote the development and popularization of

energy-efficient office equipment. As an ENERGY STAR

Partner, Brother Industries, Ltd. has determined that this

product meets the ENERGY STAR® guidelines for energy

efficiency.

Carefully observe the following precautions for the rechargeable Li-ion battery

(hereafter referred to as "rechargeable battery"), If these precautions are not followed,

overheating, leaking, or cracks in the battery may result in an electrical short,

explosion, smoke, fire, electric shock, injury to yourself or others, or damage to the

product or other property.

• Use the rechargeable battery only for its intended purpose. The P-touch labeler and

rechargeable battery are designed to function exclusively with each other. Do not insert

a different rechargeable battery into the P-touch labeler or insert the rechargeable

battery into a different P-touch labeler, otherwise fire or damage may result.

• To charge the rechargeable battery, insert the rechargeable battery into the

P-touch labeler, and then use the AC adapter designed specifically for this

P-touch labeler.

• DO NOT charge the rechargeable battery near a fire or in direct sunlight. This could

activate the protection circuitry, which is designed to prevent danger from high heat.

Activation of the protection circuitry could cause charging to stop, charging to occur

with excessive current or voltage if the protection circuitry fails, or an abnormal

chemical reaction within the battery.

• When charging the rechargeable battery, use only a battery charger designed

specifically for the rechargeable battery.

• DO NOT allow wires or other metal objects to come into contact with the terminals

of the rechargeable battery. Do not carry or store the rechargeable battery with

metal objects such as necklaces or hairpins. This could cause an electrical short,

and cause metal objects to overheat.

• DO NOT use or leave the rechargeable battery near fire, heaters, or other high

temperature (above 176°F/80°C) locations.

• DO NOT allow the rechargeable battery to come into contact with or to be immersed

in water.

• DO NOT use the rechargeable battery in corrosive environments, such as areas

where salty air, salt water, acids, alkalis, corrosive gases, chemicals, or any

corrosive liquid are present.

• DO NOT use the rechargeable battery if it is damaged or leaking.

• DO NOT directly solder any connections to the rechargeable battery. This could

cause internal insulation to melt, gas to be emitted, or safety mechanisms to fail.

• DO NOT use the rechargeable battery with the polarity (+) (-) reversed. Check the

orientation of the rechargeable battery before inserting it, and do not try to force the

rechargeable battery into the P-touch labeler. Charging the rechargeable battery

with the polarity reversed could cause an abnormal chemical reaction within the

rechargeable battery or abnormal current flow during discharge.

• DO NOT directly connect the rechargeable battery to a household electrical supply.

• Liquid (electrolyte) leaking from the P-touch labeler or rechargeable battery may

indicate that the rechargeable battery is damaged. If the rechargeable battery leaks,

immediately stop using the P-touch labeler, unplug the AC adapter, and isolate the

P-touch labeler by putting it in a bag.

Do not touch the electrolyte. If electrolyte gets in the eyes, do not rub the eyes.

Immediately rinse liberally with tap water or other clean water and seek the advice

of a medical professional. If left alone, the electrolyte could cause eye damage. If

electrolyte contacts your skin or clothing, immediately rinse them with water.

• DO NOT put the rechargeable battery, or a P-touch labeler with the rechargeable

battery installed, into a microwave oven or a high pressure container.

• DO NOT leave the rechargeable battery without power in the main unit for a long period

of time. This could shorten the life of the rechargeable battery or lead to an electrical short.

• If the P-touch labeler can only be used for a short period of time, even though the

rechargeable battery is fully charged, the rechargeable battery may have reached

the end of its service life. Replace the rechargeable battery with a new one. When

removing and replacing the rechargeable battery, cover the terminals of the old

rechargeable battery with tape to avoid creating a short in the battery.

• DO NOT disassemble, modify, or attempt to repair the rechargeable battery.

• DO NOT dispose of the rechargeable battery in fire or cause it to overheat. This

could cause the internal insulation to melt, gas to be emitted, or safety mechanisms

to fail. Additionally, the electrolyte solution could catch fire.

• DO NOT puncture the rechargeable battery with any objects, subject it to severe

shocks or throw it. Damage to the rechargeable battery's protection circuit could

cause the rechargeable battery to be recharged at an abnormal current/voltage or

cause an abnormal chemical reaction within the rechargeable battery.

• DO NOT incinerate the rechargeable battery or dispose of it with household waste.





Tips on Using the Rechargeable Li-ion Battery

• Charge the rechargeable Li-ion battery before use. Do not use it before it is charged.

• The rechargeable Li-ion battery charging can take place in 41°F-95°F (5°C-35°C)

environments. Charge the rechargeable Li-ion battery in an environment in this

temperature range. If the surrounding temperature is out of this range, the

rechargeable Li-ion battery will not be charged, and the battery indicator will remain lit.

• If the P-touch labeler is used when both the rechargeable Li-ion battery is installed

and the AC adapter is connected, the battery indicator may turn off and charging

may stop even if the rechargeable Li-ion battery has not been fully charged.





Rechargeable Li-ion Battery Characteristics

Understanding the properties of the rechargeable Li-ion battery will allow you to

optimize its usage.

• Using or storing the rechargeable Li-ion battery in a location exposed to high or low

temperatures may accelerate its deterioration. In particular, using a rechargeable

Li-ion battery with a high charge (charged 90% or more) in a location exposed to

high temperatures will considerably accelerate battery deterioration.

• Using the P-touch labeler while the rechargeable Li-ion battery is installed and

charging may accelerate the battery’s deterioration. If using the P-touch labeler

when the rechargeable Li-ion battery is installed, disconnect the AC adapter.

• If the P-touch labeler will not be used for longer than one month, remove the

rechargeable Li-ion battery from the P-touch labeler, and then store the battery in a

cool place away from direct sunlight.

• If the rechargeable Li-ion battery will not be used for a long period of time, we

recommend charging it every 6 months.

• If you touch a part of the device while a Li-ion battery is charging, the device may

feel warm. This is normal, and the device may be used safely. If the P-touch labeler

becomes extremely hot, discontinue use.





Rechargeable Li-ion Battery Specifications

• Charging time: Approximately 6 hours when charged by a AC adapter (AD-E001).

• Nominal Voltage: DC 7.2 V

• Nominal Capacity: 1850 mAh

Rechargeable Li-ion Battery

P-touch labeler

• Charging current: 800 mA

• Charging voltage: up to 8.2 V (Maximum)





Installing the Rechargeable Li-ion Battery

To remove the rechargeable Li-ion battery, reverse the installation procedure.





Charging the Rechargeable Li-ion Battery

The rechargeable Li-ion battery can be charged while it is installed in the P-touch

labeler.

Perform the following procedure to charge the rechargeable Li-ion battery.





Stopping the Rechargeable Li-ion Battery Charging

To stop the rechargeable Li-ion battery from charging, disconnect the AC adapter cord.

International ENERGY STAR® Compliance

Statement

Rechargeable Li-ion Battery (Li-ion battery

optional with the PT-P750W)

DANGER Indicates an imminently hazardous situation which, if the

product is handled without following the warnings and

instructions, will result in death or serious injuries.

Surroundings temperature range

Charge 104°F/40°C

Standard discharge current 1.9 A 140°F/60°C

Maximum discharge current 2.5 A 140°F/60°C

Shipped battery Less than 1 month -4°F - 122°F/-20°C - 50°C

Less than 3 month -4°F - 104°F/-20°C - 40°C

Less than 1 year -4°F - 68°F/-20°C - 20°C

Charging Parameters

Maximum charging voltage 8.2 Vdc

Maximum charging current 1330 mA

NOTE

Up to 6 hours is needed to fully charge the rechargeable Li-ion battery.

ATTENTION: (For USA and Canada)

The Lithium Ion battery you have purchased is recyclable. At the end of its

useful life, under various state and local laws, it is illegal to dispose of this

battery into your municipal waste stream. Please call 1-800-8-BATTERY

BA-E001

AD-E001

Charging Full charge

Unpacking the PT-P750W and Parts

Description

Check that the package contains the following before using the P-touch labeler. If any

item is missing or damaged, contact your Brother reseller.

Setting the Tape Cassette

Connecting the Power Supply

Using the AC adapter

Using the batteries

To remove the batteries, reverse the installation procedure.

Turning the P-touch labeler On or Off

On: Press the Power button.

Off: Press and hold the Power button until the Status lamp is lit in orange.

Creating a Label using P-touch Editor

Lite

1. Turn on the P-touch labeler (1), then press and hold down the Editor Lite button

until the green Editor Lite lamp lights up (2). Connect the USB cable to the

computer and PT-P750W.

Brother Support website

support.brother.com/g/d/d5p2/

Please visit our Support website.

You can find following information:

• Software download

• Manuals/Documents

• Frequently Asked Questions (Troubleshooting, Useful tips on using printer)

• Consumable information and the latest OS compatibility information.

You can also see setup steps on the website.

Click the "Getting ready to use your printer." link in the "information" section.

The contents of this website are

subject to change without notice.

• PT-P750W • AC adapter (AD-E001) • USB cable

• Starter tape cassette

1 Top panel

2 Editor Lite lamp

3 Editor Lite button

4 Wireless mode button

5 Tape exit slot

6 Wi-Fi lamp

7 NFC lamp

8 Feed & Cut button

9 Status lamp

10 Battery lamp

11 Power button

12 Battery cover

13 Mini-USB port

14 AC adapter connector

15 Cassette cover

16 NFC tag

17 Release lever

18 Print head

19 Tape cutter

20 Cutter blade

CAUTION

If you cannot close the cassette cover, check to ensure the white lever is in the

up position. If not, lift the lever, and then attach the cover.

NOTE

• Make sure that there is no slack in the tape.

• When setting or removing the tape cassette, make sure that the tape does not

catch on the protrusion (1) or the print head.

13 15

12 17

CAUTION

• Remove the batteries if you do not intend to use the P-touch labeling system

for an extended period of time.

• Dispose of the battery at an appropriate collection point, not in the general

waste stream. In addition, be sure to observe all applicable federal, state, and

local regulations.

• When storing or discarding the battery, wrap it (for

example with cellophane tape), to prevent it from

short-circuiting.

(Battery insulation example)

1. Cellophane tape

2. Alkaline or Ni-MH battery

NOTE

When turning the P-touch off, keep the AC adapter connected or the batteries

installed until the Status lamp goes off.

AD-E001

LR6 or HR6

ELECTRONIC LABELING SYSTEM

English

User’s Guide

Printed in China

LAE838001

Español

PT-P750W

Read this guide before you start using your P-touch labeler.

Keep this guide in a handy place for future reference.

Produktspecifikationer

Varumärke:	Brother
Kategori:	Etikettskrivare
Modell:	P-touch PT-P750W

Behöver du hjälp?

Om du behöver hjälp med Brother P-touch PT-P750W ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Etikettskrivare Brother Manualer

Brother PT-H101GB Bruksanvisning

16 Oktober 2024

Brother P-Touch PT-1290DT Bruksanvisning

16 Oktober 2024

Brother QL-570 Bruksanvisning

13 Oktober 2024

Brother TD-2120N Bruksanvisning

10 Oktober 2024

Brother P-Touch PT-D600VP Bruksanvisning

28 September 2024

Brother P-touch 1000 Bruksanvisning

27 September 2024

Brother PT-D460VP Bruksanvisning

21 September 2024

Brother PT-D610VP Bruksanvisning

21 September 2024

Brother P-touch PT-1880W Bruksanvisning

21 September 2024

Brother P-Touch 2430PC Bruksanvisning

19 September 2024

Etikettskrivare Manualer

Nyaste Etikettskrivare Manualer

GoDEX RT230 Bruksanvisning

27 Oktober 2024

GoDEX RT860i Bruksanvisning

27 Oktober 2024

Citizen CBM1000 Bruksanvisning

18 Oktober 2024

Citizen CT-P290 Bruksanvisning

17 Oktober 2024

GoDEX G330 Bruksanvisning

16 Oktober 2024

Dymo 1540 Bruksanvisning

15 Oktober 2024

Dymo LabelPoint 150 Bruksanvisning

15 Oktober 2024

Dymo LabelWriter 450 Turbo Bruksanvisning

13 Oktober 2024

Dymo LabelManager LM160 Bruksanvisning

12 Oktober 2024

Citizen CLP-1001 Bruksanvisning

12 Oktober 2024