BTI Aqua-Solutions HT4105 Bruksanvisning

BTI Aqua-Solutions Pannor & pannor HT4105

Läs nedan 📖 manual på svenska för BTI Aqua-Solutions HT4105 (8 sidor) i kategorin Pannor & pannor. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/8
DIGITAL INSTANT HOT WATER DISPENSER INSTALLATION INSTRUCTIONS
ITEM HT4105
PATENT PENDING
REV 4/02/18
Make sure all electrical wiring, connections and water connections conform to local codes.
A standard 110V electrical outlet is required under the sink to power the Dispenser and must supply power CONTINUOUSLY to the
Dispenser.
The cord/plug supplied with the Dispenser must be connected to the power outlet.
The Digital Instant Hot Water Dispenser is a non-pressurized, open vented system with a built-in pressure regulator valve (PRV) that
limits operating pressure to 60 psi.
A Hot & Cold or Hot Only Filtration Faucet must be installed before the Digital Instant Hot Water Dispenser, creating an “open vent”
system, consequently, no pressure is built up inside the Dispenser.
TOOLS REQUIRED PARTS INCLUDED
• Adjustable wrench
• Phillips screwdriver
• 3/8” x 5/16” hot-outlet adapter
• 3/8” x 1/4” cold-inlet adapter
IMPORTANT - WHAT YOU NEED TO KNOW BEFORE YOU START
We are delighted you have chosen the BTI Aqua-Solutions Digital Instant Hot Water Dispenser for use in your home. When used in con-
junction with a Hot & Cold or Hot Only BTI Aqua-Solutions Filtration Faucet, or any other open vented -line filtration faucet, this unit will 3
give you years of hot water whenever you require it.
Please read and follow this step-by-step guide to installation, operation, and care for the Digital Instant Hot Water Dispenser and you will
soon be making your rst cup of coffee, tea, soup, oatmeal or a variety of other items - instantly - and at optimal temperature!
For your safety and a worry-free installation, please read and follow all the instructions, cautions and warnings BEFORE installation or
use of this Digital Instant Hot Water Dispenser. The BTI Aqua-Solutions Digital Instant Hot Water Dispenser is intended only for residen-
tial, not commercial use.
•
•
•
•
•
1
SAFETY INSTRUCTIONS - READ BEFORE YOU START
These instructions are only intended as a guide. If there is any doubt about installation,
please contact a licensed/certied plumber and/or electrician.
•
•
•
•
•
•
ENSURE THE DIGITAL INSTANT HOT WATER DISPENSER IS NOT CONNECTED TO ELECTRIC POWER DURING THE INSTALLATION.
Using an ungrounded or improper connection of the power supply to the product can cause serious injury or death from
electrical shock. ALWAYS use the USA IEC Power Cord supplied with the unit.
The Digital Instant Hot Water Dispenser must be mounted vertically and level. Because the Digital Instant Hot Water Dispenser is
not under pressure, there is a slight delay in water ow after the Hot & Cold or Hot Only Filtration Faucet handle is turned on. This
is normal and indicates the Digital Instant Hot Water Dispenser is functioning properly.
It is recommended that a “handle spring-back” type Filtration Faucet, like the BTI Aqua-Solutions 2100, 2200 or 2400 Series
Filtration Faucets, is used with the Digital Instant Hot Water Dispenser to protect the user from continuous dispensing of hot
water and possible injury from same.
Place the Digital Instant Hot Water Dispenser in position, check and ensure that the ltration faucet hoses and the power cord to
the electrical outlet will reach without being stretched.
The Digital Instant Hot Water Dispenser must be positioned so the hoses to and from the Filtration Faucet do not twist or kink.
ELECTRICAL REQUIREMENTS
•
•
•
A 110V electrical power supply is required.
It is recommended that a separate circuit serving only the Digital Instant Hot Water Dispenser be provided OR use an outlet that
can be turned On/Off by a switch.
The Digital Instant Hot Water Dispenser is equipped with a power supply cord with a power plug. To minimize possible shock
hazard, the cord must be plugged into a mating ground-type outlet, grounded in accordance with all local codes and ordinances.
PLUMBING REQUIREMENTS
•
•
•
•
If local codes permit, the Hot & Cold or Hot Only Filtration Faucet hoses should be connected to hot and cold water supply lines
using shut-off valves.
The use of ltered, clean water with impurities removed is advised. Place a point-of-use ltration unit such as the BTI
Aqua-Solutions FL1000 in-line PRIOR to the Filtration Faucet.
Unltered water with impurities, grains of sand, etc., can clog the Dispenser and Filtration Faucet and cause the Dispenser’s
5-year warranty to be voided.
Connecting a standard, pressurized faucet may cause injury and will damage the electronic components of the Digital Instant Hot
Water Dispenser and void the 5-year warranty.
ENVIRONMENT REQUIREMENTS
•
•
DO NOT install the Instant Hot Water Dispenser outdoors or in a location where the temperature may fall below 32ºF.
The installation environment should be ventilated, with protection from direct sunlight, in a humidity range of 10-70%.
ITEM HT4105
2
HOW A VENTED FAUCET WORKS
Water ows from supply line (A) into the faucet base (B).
Water is then diverted inside the faucet into line (C) and into the Digital
Instant Hot Water Dispenser (D).
The fresh water displaces hot water in the Dispenser, causing it to ow
freely through line (E) to the ltration faucet.
Hot water continues straight through the ltration faucet and exits
the spout, (F).
A
IMPORTANT!
NEVER OPERATE THE FAUCET IF THE CLEAR OUTLET TUBE (E) IS KINKED!
NEVER CONNECT AN INSTANT HOT WATER DISPENSER DIRECTLY TO A
STANDARD FAUCET. CONNECTION TO A FAUCET OTHER THAN A -LINE 3
VENTED FAUCET CAN CAUSE INJURY, INTERNAL DAMAGE TO DISPENSER
AND WILL VOID 5-YEAR WARRANTY.
ITEM HT4105
D
B
C
E
F
1. FOR FLOOR-MOUNT INSTALLATION - CHOOSE LOCATION FOR DISPENSER
Find a location under the sink that has access to an
electrical outlet and is close enough to connect the
faucet lines without kinking them. For the unit to oper-
ate properly, it cannot be installed beyond the reach of
the manufacturer-provided electrical cord. Leave 1-2”
clearance around the Dispenser for air ow.
WARNING!
DO NOT PLUG IN THE INSTANT HOT WATER DISPENSER UNTIL IT IS FILLED WITH WATER.
HEATING THE DISPENSER WHILE EMPTY WILL DAMAGE THE UNIT AND VOID THE 5-YEAR WARRANTY.
INSTANT HOT WATER DISPENSER INSTALLATION PROCEDURE
2. CABINET-SIDE MOUNT
If mounting on side of cabinet,
install 2 screws into cabinet side that align with the
mounting holes on the back of the Dispenser.
Leave 1”-2” clearance around Dispenser for air ow.
3

Produktspecifikationer

Varumärke: BTI Aqua-Solutions
Kategori: Pannor & pannor
Modell: HT4105

Behöver du hjälp?

Om du behöver hjälp med BTI Aqua-Solutions HT4105 ställ en fråga nedan och andra användare kommer att svara dig


Pannor & pannor BTI Aqua-Solutions Manualer

BTI Aqua-Solutions

BTI Aqua-Solutions HT4105 Bruksanvisning

31 Mars 2025

Pannor & pannor Manualer

Nyaste Pannor & pannor Manualer

Sime

Sime HOME PLUS Bruksanvisning

1 April 2025
Philips

Philips AquaShield AWH5319 Bruksanvisning

13 Mars 2025
Corberó

Corberó CTEV350 Bruksanvisning

10 Mars 2025
Corberó

Corberó CTM80 Bruksanvisning

10 Mars 2025
Rinnai

Rinnai V65iP Bruksanvisning

4 Mars 2025
Rinnai

Rinnai RUCS65iP Bruksanvisning

4 Mars 2025
Midea

Midea M2605 Bruksanvisning

27 Februari 2025
Midea

Midea JSD12-6DH4 Bruksanvisning

27 Februari 2025
Midea

Midea JSD20-10DH4 Bruksanvisning

27 Februari 2025
Stiebel Eltron

Stiebel Eltron SHC 15 AU Bruksanvisning

27 Februari 2025