Cateye Enduro CC-ST250v3 Bruksanvisning

Cateye Cykeldator Enduro CC-ST250v3

Läs nedan 📖 manual på svenska för Cateye Enduro CC-ST250v3 (2 sidor) i kategorin Cykeldator. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

#169-9731

Heavy Duty Wire and Bracket Sensor Kit

Kit de Fil Renforce et Supports d'Unité Principale et de Détecteur

Nachrüstset mit Halterung, Sensor und verstärktem Sensorkabel

Extra sterke kabel en bracket sensor set

Filo Ultra Resistente e Attacco Completo

Kit Soporte del Sensor y Alambre de Servicio Pesado

ヘビーデューティワイヤ&ブラケットセンサーキット

#169-9750

Attachment Kit

Kit de Gamitures

Befestigungsmaterial

Kabelbevestigingset

Guarnizioni da montare

Elementos de fijación

アタッチメントキット

#169-6280

Universal Sensor Band

Garniture Universelle pour Détecteur

Universal Befestigungsband

Universele Sensor klemstrip

Guanizione Universale per Sensore

Banda del Sensor Universal

ユニバーサルセンサーバンド

#166-5120

Wheel Magnet

Aimant pour roue

Radmagnet

Wielmagneet

Magnete ruota

Iman de la rueda

ホイールマグネット

#169-6180

Lithium Battery (CR1620)

Pile au lithium

Lithium-Batterie

Lithum Batterij

Bateria al Litio

Bateria de Litio

リチウム電池

Setting Values Cross Reference Table (The tire size is marked on both sides of the tire.)

Table de Correspondance des Valeurs de Réglage (La dimension du pneu figure de chaque côté du pneu)

Wertetabelle zur Einstellung des Radumfanges (die Radgröße entnehmen Sie der Aufschrift des Reifens)

Tabel voor het bepalen van de wielomtrek (de bandenmaat staat vermeld aan beide zijden van de band)

Tabella delle Corrispondenze dei Valori di Regolazione (La dimensione del pneumatico figura su ogni lato del pneumatico)

Tabla de Valores (El tamaño de la rueda está marcado al lado de la llanta)

タイヤ周長ガイド（タイヤサイズは通常タイヤの側面に記載されています）

Specificat ions/Caracteristiques techniques/ / /Technische daten Specificaties

Caratteristiche tecniche/

Especificaciones

/仕様

Controller/Calculateur/Controler/ /Controleur Elaboratore/

Contador

/制御方式

------------------------------------------------------------------ 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)

Display/Affichage/Anzeige/ / /Display Visualizzazione

Pantalla

/表示方式

----------------------------------------------------------------------------------------------------------------- Liquid Crystal Display

Sensor/Détecteur/Sensor/Sensor/ /Rivelatore

Sensor

/検知方式

------------------------------------------------------------------------------------------------------- No Contakt Magnetic Sensor

Operating Temperature Range/Température d’utilisation/zulässige Betriebstemperatur/ /Toegestane temp. Temperatura di utilizzo/使用温度範囲

------------------------------------------------------------------------------------------------------------ 0 C(32 F)°C - 40° °F - 104°

CO.,L TD.

U.S. Pat. Nos. 4636769/4642606/5236759/5226340

and Design Patented

CCMST25-970422 Printed in Japan 0687265

CATEYE ENDURO

CYCLOCOMPUTER

Model CC-ST250

TIRE SIZE L(cm) TIRE SIZE L(cm) TIRE SIZE L(cm)

dimension du pneu dimension du pneu dimension du pneu

Radgröße Radgröße Radgröße

bandenmaat bandenmaat bandenmaat

dimensione del pneumatico dimensione del pneumatico dimensione del pneumatico

Tamaño de rueda Tamaño de rueda Tamaño de rueda

タイヤサイズタイヤサイズタイヤサイズ

20 x 1.75 150 26 x 1.40 200 650 x 38B 211

24 x 1 175 26 x 1.50 199 700 x 18C 207

24 x 3/4 Tubular 178 26 x 1.75 202 700 x 19C 209

24 x 1-1/8 Tubular 179 26 x 1.95 205 700 x 20C 209

24 x 1-1/4 191 26 x 2.00 206 700 x 23C 210

24 x 1.75 189 26 x 2.1 207 700 x 25C 211

24 x 2.00 192 26 x 2.125 207 700 x 28C 214

24 x 2.125 196 26 x 2.35 208 700 x 30C 217

26 x 1(559mm) 191 27 x 1 215 700 x 32C 216

26 x 1(650c) 195 27 x 1-1/8 216 700C Tubular 213

26 x 1.25 195 27 x 1-1/4 216 700 x 35C 217

26 x 1-1/8 Tubular 197 27 x 1-3/8 217 700 x 38C 218

26 x 1-3/8 207 650 x 35A 209 700 x 44C 222

26 x 1-1/2 210 650 x 38A 212

LIMITED WARRANTY

1-Year Warranty for Main Unit Only

(Accessories/Attachments and Battery Consumption excluded)

If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. The service must be

performed by Cat Eye Co., Ltd. To return the product, pack it carefully and remember to enclose the warranty certificate with

instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and

transportation charges to our service shall be borne by person desiring service.

(Address for service)

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

Attn.: CAT EYE Customer Service Section

Service & Research Address for United States Consumers:

CATEYE Service & Research Center

1705 14th St. 115 Boulder, CO 80302

Phone: 303-443-4595 Toll Free: 800-5CATEYE

Fax: 303-473-0006 e-mail: CatEyeUSA@aol.com

GARANTIE LIMITÉE

1 An de Garantie sur l'Unité Principale Uniquement

(Les accessoires et la pile sont exclus de la garantie)

En cas de problème en cours d'utilisation normale, l'unité principale sera réparée ou remplacée gratuitement.

Par Cat Eye Co., Ltd. Lors du renvoi du produit, il y a lieu de l'emballer soigneusement et de joindre le certificat

de garantie avec les instructions de réparation. Les nom et adresse de l'acheteur doivent figurer de manière

lisible sur le certificat de garantie. Les frais d'assurance, de manutention et d'envoi à notre Service Réparations

seront supportés par le demandeur de la réparation.

Adresse Service Réparations

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

Attn.: CAT EYE Customer Service Section

BEGRENZTE GARANTIE

1-Jahr-Garantie: Auf den Computer

(Ersatzteile/Zubehörteile sowie Batterie nicht eingeschlossen)

Falls während des normalen Gebrauchs Fehler auftreten, wird das entsprechende Teil kostenlos repariert

oder ersetzt. Die Reparatur muß von CAT EYE Co., Ltd. durchgeführt werden, und das zu reparierende

Produkt muß direkt durch den Händler an CAT EYE Co., Ltd. gesandt werden. Bei der Rückgabe des

Gerätes zur Reparatur packen Sie es sorgfältig anbei. Achten Sie darauf, Ihren Namen und Ihre Anschrift

klar und deutlich lesbar auf die Garantiekarte zu schreiben, damit das Gerät so schnell wie möglich nach

Beendigung der notwendigen Reparatur/Einstellung an Sie zurückgesandt werden kann.

Anschrift bei Garantieansprüchen

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

z. H.: CAT EYE Kundendienstabteilung oder wenden Sie sich bitte an den entsprechenden Importeur.

GARANTLEBEPALINGEN

1 jaar garantie, alleen geldig op de computer (accessoires, aansluitingen en

gebruik van batterij uitgezonderd)

Mochten er problemen optreden gedurende normaal gebruik, dan geschiedt reparatie of vervanging kosteloos. Dit doent door de

fabrikant Cateye Co., Ltd. uitgevoerd te worden. Bij terugzending van de computer moet deze zorgvuldig verpakt worden en dient het

garantiebewijs en een beschrijving van het probleem meegezonden te worden. Vermeld duidelijk uw naam en adres in blokletters o f

getypt op het garantiebewijs. Verzekerings- verzend- en transportkosten zijn voor rekening van de koper.

Service adres:

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

ter attentie van: Cateye klantenservice

GARANZIA LIMITATA

1 Anno di Garanzia soltanto sull'Unità Principale

(Gli accessori e la pila sono esclusi dalla garanzia)

In caso di problema durante l'impiego normale, l'unità principale verrà riparata o sostituita gratuitamente da Cat Eye Co., Ltd.. Al

momento del ritorno del prodotto occorre imballarlo con cura allegandovi il certificato di garanzia con le istruzioni per le riparazioni.

Il nome e l'indirizzo dell'acquirente devono essere presenti in modo leggibile sul certificato di garanzia. Le spese di assicurazione,

di manutenzione e di spedizione al nostro Servizio Riparazioni saranno a carico del richiedente la riparazione.

Indirizzo Servizio Riparazioni

2-8-25 Kuwazu, Higashi Sumiyoshi-ku, OSAKA 546, Giappone.

Att:Dipartamento Assistenza Clienti

GARANTIA LIMITADA

Se garantiza por un año únicamente el grupo central

(Los accesorios, aditamentos y el consumo de la pila están excluidos)

Si ocurriera alguna avería durante el uso normal, se reparará o sustituirá la pieza o el grupo central. Cat Eye Co., Ltd.

deberá realizar la reparación. Para devolver el producto, envuélvalo cuidadosamente y no olvide incluir el certificado de

garantía y las instrucciones para repararlo. Rogamos escribir claramente a mano o a máquina su nombre y dirección. Los

gastos de seguro, manipulación y transporte serán a cargo de la persona que solicite la reparación.

Dirección para las reparaciones:

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan

Attn.: CAT EYE Customer Service Section

製品保証について

1年保証：コンピュータのみ（付属品及び電池の消耗は除く）

正常な使用状態で万一故障した場合は無料で修理・交換いたします。保証書にお客様のお名前・ご住所・

ご購入日・故障状態をご記入の上、製品と共に当社宛て直接お送りください。お送りいただく際の送料は

お客様にてご負担願います。修理完了後、当社より郵送にてお届けさせていただきます。

［宛先］

製品サービス課

〒546 大阪市東住吉区桑津2丁目8番25号

TEL: (06)719-2631 FAX: (06)719-2362

＊アクセサリーパーツを別途販売していますのでご利用ください。

MEASURING AND DISPLAY FUNCTIONS

OPERATING INSTRUCTIONS

magnet

sensor

band B

sensor

band A

Fig.12

Fig.10

rubber pad

sensor band B

Fig.11

sensor band A

sporkes

Fig.8

Fig.9

screw

markingline

of sensor

magnet sensor

Fig.13

nyron ties

Fig.14

bracket

screw cap

Fig.15

SPD Current Speed

0.0(3.0) - 65 mile/h(27inch) 1 mile/h under31 miles/h±

This is always displayed on the main display and updated once a second.

ODO Total Distance (Odometer) 0.0 - 9999.9 mile ±0.1 mile

This is continuously measured until battery wears down or all clear operation is

done. At 10,000 miles(km), it returns to zero and counting begins anew.

DST Trip Distance 0.00 - 999.99 mile ±0.01 mile

The trip distance from start to current point is displayed. With Reset operation,

it returns to zero.

TM Elapsed Time 0:00'00" - 9:59'59" ±0.003 %

Elapsed time is measured from start to current point, in units of hours, minutes

and seconds. At 10 hours, it returns to zero and counting begins anew. With

Reset operation, it returns to zero.

AVS Average Speed 0.0 - 65.0mile/h ±0.3 mile/h

The average speed from start to current point is displayed within 27 hours 46

minutes 39 seconds (99,999 seconds) or 999.99 miles (km). If either is ex-

ceeded, (.E) is displayed and calculation ceases.

MXS Maximum Speed 0.0(3.0) - 65 mile/h(27inch) ±1 mile/h

With Reset operation, it returns to zero and counting begins anew.

12-hour clock time 0:00' - 11:59' ±0.003 %

The current time is displayed by a 12-hour clock.

DST

ODO

DST

AVS

MXS

This function switches the main unit to start or stop automatically, in which AUTO

symbol appears on the screen, and you are free from pressing S/S button each

time.

•How to switch on/off the Auto Function.

In TM, DST or AVS, this function switches on/off with each press of SET button.

When on, AUTO symbol appears. *With this function, it ceases measuring

elapsed time during a stop.

* 2 seconds may be elapsed if mount the main unit to the bracket with this func-

tion on.

AUTO

DST

TROUBLE SHOOTING

• The following situations do not indicate malfunction of the cyclocomputer. Check the

following before taking to repair.

* When current speed does not appear, short-circuit the contact on the back with metal.

The unit will function normally if the speed display appears.

Display response is slow.

----- Is it at a low temperature under 32° °F(0 C)?

----- It returns to normal state when temperature rises.

No display.

----- Has the Lithium Battery in the main unit worn out?

----- Replace the Lithium Battery with a new one.

Incorrect data appear.

----- Execute "All Clear" operation.

Current speed does not appear.

----- Is there anything on the contact of the main unit or of the bracket?

----- Wipe the contact clean.

----- Is the distance between sensor and magnet too far?

----- Are the marking line of the sensor and the center of magnet matched each other?

----- Refer to "Sensor/Magnet Mounting" and re-adjust correctly.

----- Is the wire broken?

----- Replace the Bracket & Sensor part with a new one.

Transmission signal loss in damp or wet conditions.

----- Contacts on the bracket might not be repelling wets efficiently.

----- Water or condensation may collect between the bracket sensor and the computer causing an

interruption in the data transmission. Wipe the contacts with dry cloth. Contacts can also be

treated with a water repellent silicon jell from an automotive parts or hardware store. Do not

use industrial water repellent; it may damage the bracket.

When the S/S button is pressed, the unit doesn't activate or stop.

----- Is the unit in the Auto function?

----- The S/S button doesn't function in the Auto function.

MAINTENANCE/PRECAUTIONS

• Do not leave the main unit exposed to direct sunlight when the unit is not in use.

• Do not disassemble the main unit, sensor and magnet.

• Don't pay too much attention to your computer's functions while riding! Keep your eyes on the

road and duly consider to traffic safety.

• Check relative position of sensor and magnet periodically.

• For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth. Do not apply

paint thinner, benzine, or alcohol, to avoid damages on the surface.

• If there is mud, sand or the like clogs between the button and the body, the movement of the

button may be disturbed. Softly wash away such objects with water.

SPECIFICATIONS

Applicable Cycle Sizes 130cm - 229cm

Applicable Fork Diameter 11ø - 40ø (S:11 - 26ø L:21 - 40ø)

The length of the wire 70cm

Power Supply Lithium Battery (CR1620/CR1616) x 1

Battery Life Approx. 3 years(The life of the first factory-loaded battery may

be shorter than this period.)

Dimension/Weight 1-15/16" x 1-25/32" x 5/8" (49 x 45 x 16 mm) / 0.74 oz (21 g)

* The specifications and design are subject to change without notice.

center of

magnet

rubber pad

POWER SAVING FUNCTION

A. Main Display (Speed)

B. Sensor Pulse Symbol

C. Mode Symbol

D. Speed Scale Symbol

E. Auto Mode Symbol

F. Sub-Display

(Selected Function)

G. M (Mode) Button

H. S/S (Start/Stop) Button

I. Set Button

J. Battery Case Cover

K. Contact

1. Bracket

2. Wire

3. Sensor

4. Sensor Bands-A (S)(L)

5. Sensor Bands-B

6. Magnet

7. Sensor Band Rubber Pad

Bracket Rubber Pad (2 pcs.)

9. Nylon Tie (3 pcs.)

10. Sensor Band Screw (S)(L)

11. Spiral Tube

When main unit is left without receiving any signal for 60-70 minutes continu-

ously, power supply is shut down and main unit will display ( ) only as the

figure. By pressing M button or S/S button, or by receiving signal, this function is

released.

rubber pad

parallel

sensor

about 2mm

outer cable

wire

OPEN

AUTO (AUTOMATIC START/STOP) FUNCTION

BUTTON FUNCTION

• M button (Fig.1)

Changes the display in the order shown in fig. 1, and data is displayed

on the sub-display. *If held over 2 seconds, 12-hour clock appears.

• S/S button

Starts and stops the measurement of trip distance and elapsed time.

During operation, speed scale symbol flashes. In Auto Function, this

button is invalid.

• SET Button

This is for setting the wheel circumference and clock time, switching on/

off Auto Function and to clear all present data and any irregularity.

When pressed in stop state in each mode, the following can be revised.

• In ODO mode --------------------- Wheel circumference

• In mode ----------------------- 12-hour clock

• In TM, DST or AVS mode ----- On/off the Auto function

Reset Operation: (Fig.2)

Select any mode except ODO, then press M button and S/S button si-

multaneously. MXS, AVS, DST and TM will become zero. (When done

in ODO, registered wheel circumference will be displayed.)

All Clear Operation: (Fig.3)

When M button, S/S and set buttons are pressed simultaneously, all

data stored (ODO, speed scale, Wheel circumference and clock time) is

erased. All displays illuminate, then mile/h symbol illuminates. This

should only be executed after replacing battery or when irregular dis-

play occurs due to static electricity, etc. Since all memories are erased,

set necessary data again according to "Main Unit Preparation".

MAIN UNIT PREPARATION

The following must be completed before operating.

(1) How to measure wheel circumference (L) of your bike (Fig.4)

Put a mark on the tire tread and ride the bike one full wheel revolution.

Mark the start and the end of the revolution on the ground and then

measure the distance between the two marks. This is your actual cir-

cumference. Or, the "Selecting Values Cross Reference Table" tells

you an approximate circumference according to tire size.

(2) Setting Speed Scale

Preform all clear operation. All displays will illuminate. Then mile/h

alone will be displayed as illustrated in fig.5. Km/h and mile/h are alter-

nately displayed with each press of S/S button. Press M button to set

desired speed scale. The display will change as fig. 6.

(3) Setting the wheel circumference (Fig.6)

The standard wheel circumference of 216 cm for 27" wheel is displayed.

When using 216 cm without revision, press M button. ODO will be dis-

played and 216 cm is set. For revision, press S/S button to increase the

number by one. To increase rapidly, hold down the button. When the

desired number appears, press M button. ODO will be displayed, and

the desired number is set.

(4) Resetting or changing the wheel circumference

Set main unit in ODO with M button, and stop it with S/S button. Press

SET button. The stored number will flicker on the sub-display. Revise

the number as desired according to the instructions in (3).

Setting the clock time (Fig.7)

Press M button over 2 seconds to select , and stop it with S/S but-

ton. Then press SET button, and minutes flash. Press S/S button to

advance minutes by one. To advance rapidly, hold down the button. Set

the time one or two minutes ahead of the current time. Then press M

button, and hours will flash. Use S/S button the same way. Press SET

button to complete time setting. *When you press the SET button, the

undisplayed seconds will turn to zero. For accuracy, set by the radio

time signal.

MOUNTING TO BIKE

• The spokes must run correctly through the inside the magnet as in

fig.8.

• Attach the sensor with Sensor Bands-A-B to the right fork. Choose a

band that fits the fork diameter (S size for up to 24ø, L for oversize).

If the front fork is thick, use the longer screw.

1. Insert the band-B into the slit of the band-A, and put the rubber pad

inside of the band-A(fig. 9). Adjust the length in order that the

screw-fastening part of the bands are parallel when mounted to

the fork(fig. 10). *To pull out the band B from band A, tug strongly.

2. Mount the adjusted bands to the fork along with the sensor, by

temporarily tightening the screw(fig. 11).

3. Align the magnet's center and the sensor's marking line(fig. 12),

and make sure of 2mm clearance between the magnet and sensor

(fig. 13). Then tighten the screw securely. Cut the excess of the

band-B with a nipper or the like.

• Secure the wire with nylon ties as shown in fig. 14. Wind the wire

round the outer cable and wrap these wires with the spiral tube. Ad-

just the length of the wire. Loosen the wire in the area marked with

the arrow so that the wire does not hinder handlebar operation.

• Use either 1mm- or 2 mm-thick pads if necessary, according to

handlebar diameter. Attach the bracket close to the handlebar stem

(fig. 15).

• Slide main unit onto the bracket from front until it clicks into position.

To remove, pull it off forward while pushing down the lever. (fig. 16)

•Test (Fig.16)

Mount main unit. If main display does not show any figures, press either

M button or S/S button to release from power saving function. Spin the

wheel to check if sensor pulse symbol flashes. If not, adjust relative

positions of magnet and sensor following the instructions.

HOW TO REPLACE THE BATTERY

Turn main unit over, remove battery case cover with coin and insert a

new lithium battery properly (CR1620 or CR1616) with the (+) pole up-

ward (fig.17), and close the cover securely.

* Please make sure to do the All Clear operation after replacing bat-

tery, and to set the unit again.

Fig.6

Fig.7

Fig.4

Fig.5

Fig.1

Fig.2

Fig.3

RESET

ALL CLEAR

fork

lever

Fig.16

Fig.17

spiral tube

sensor band A

Produktspecifikationer

Varumärke:	Cateye
Kategori:	Cykeldator
Modell:	Enduro CC-ST250v3

Behöver du hjälp?

Om du behöver hjälp med Cateye Enduro CC-ST250v3 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Cykeldator Cateye Manualer

Cateye Inou MSC-GC100 Bruksanvisning

29 September 2024

Cateye Quick CC-RS100W Bruksanvisning

21 September 2024

Cateye Padrone+ CC-PA110W Bruksanvisning

21 September 2024

Cateye Padrone Digital CC-PA400B Bruksanvisning

21 September 2024

Cateye Mate CC-3000 Bruksanvisning

21 September 2024

Cateye Padrone CC-PA100W Bruksanvisning

24 Augusti 2024

Cateye Padrone Smart plus CC-VT235W Bruksanvisning

24 Augusti 2024

Cateye V3N CC-TR210DW Bruksanvisning

22 Augusti 2024

Cateye Velo CC-VT230W Bruksanvisning

19 Augusti 2024

Cateye Stealth CC-GL50 Bruksanvisning

14 Augusti 2024

Cykeldator Manualer

Nyaste Cykeldator Manualer

Bosch Purion BUI215 Bruksanvisning

18 Oktober 2024

BBB BCP-35W Bruksanvisning

12 Oktober 2024

Crivit HG01734A Bruksanvisning

4 Oktober 2024

Sigma Pure GPS Bruksanvisning

2 Oktober 2024

Bryton Rider 20 Bruksanvisning

2 Oktober 2024

Lezyne Mega XL GPS Bruksanvisning

30 September 2024

Sigma BC 1600 Bruksanvisning

30 September 2024

Wahoo Elemnt Roam v2 Bruksanvisning

26 September 2024

VDO R4 Bruksanvisning

25 September 2024

VDO R5 Bruksanvisning

25 September 2024