Chauvin Arnoux CA 10101E Bruksanvisning

Chauvin Arnoux Mätutrustning CA 10101E

Läs nedan 📖 manual på svenska för Chauvin Arnoux CA 10101E (36 sidor) i kategorin Mätutrustning. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/36

pH-meter

EN - User’s manual

CA 10101E

Information or useful tip.

Battery.

Earth.

The product is declared recyclable following an analysis of the life cycle in accordance with standard ISO 14040.

Chauvin Arnoux has adopted an Eco-Design approach in order to design this appliance. Analysis of the complete life-

cycle has enabled us to control and optimize the e󰀨ects of the product on the environment. In particular this appliance

exceeds regulation requirements with respect to recycling and reuse.

The CE marking indicates compliance with the European Low Voltage Directive (2014/35/EU), Electromagnetic

Compatibility Directive (2014/30/EU), and Restriction of Hazardous Substances Directive (RoHS, 2011/65/EU and

2015/863/EU).

The rubbish bin with a line through it indicates that, in the European Union, the product must undergo selective disposal

in compliance with Directive WEEE 2012/19/EU. This equipment must not be treated as household waste.

PRECAUTIONS FOR USE

This instrument is compliant with safety standard IEC/EN 61010-2-030 or BS EN 61010-2-030, for voltages 5V with report to

ground. Failure to observe the safety instructions may result in electric shock, re, explosion, and destruction of the instrument

and of the installations.

■The operator and/or the responsible authority must carefully read and clearly understand the various precautions to be taken

in use. Sound knowledge and a keen awareness of electrical hazards are essential when using this instrument.

■Observe the conditions of use, namely the temperature, the relative humidity, the altitude, the degree of pollution, and the place

of use.

■Do not use the instrument if it seems to be damaged, incomplete, or poorly close.

■Before each use, check the condition of the housing. Any item of which the insulation is deteriorated (even partially) must be set

aside for repair or scrapping.

■All troubleshooting and metrological checks must be done by competent, accredited personnel.

Thank you for purchasing this CA 10101E pH-meter.

For best results with your instrument:

■read these operating instructions carefully,

■comply with the precautions for use.

CONTENTS

1. FIRST USE ............................................................................................................................................................................... 4

1.1. Delivery condition 4 ...........................................................................................................................................................

1.2. Accessories .................................................................................................................................................................... 4

1.3. Replacement parts 4 .........................................................................................................................................................

1.4. Inserting the batteries 5 .....................................................................................................................................................

2. PRESENTATION OF THE INSTRUMENT ............................................................................................................................. 6

2.1. CA 10101E 6 .....................................................................................................................................................................

2.2. Terminal strip .................................................................................................................................................................. 6

2.3. Functions of the instrument 7 ............................................................................................................................................

2.4. Keypad 7 ...........................................................................................................................................................................

2.5. Display 8 ............................................................................................................................................................................

2.6. Setting the time 8 ...............................................................................................................................................................

2.7. Prop 9 ................................................................................................................................................................................

3. USE IN STAND-ALONE MODE ........................................................................................................................................... 10

3.1. pH measurement 10 ..........................................................................................................................................................

3.2. Oxidation reduction potential measurement (ORP) 16 .....................................................................................................

3.3. Recording the measurements 19 ......................................................................................................................................

3.4. Analogue outputs .......................................................................................................................................................... 20

3.5. Errors 22 ............................................................................................................................................................................

4. USE IN RECORDING MODE ............................................................................................................................................... 23

4.1. Connection 23 ...................................................................................................................................................................

4.2. Get Data Logger Transfer software 23 ..............................................................................................................................

4.3. USB link 23 ........................................................................................................................................................................

4.4. Data Logger Transfer software 25 .....................................................................................................................................

4.5. Other software 27 ..............................................................................................................................................................

5. TECHNICAL CHARACTERISTICS ..................................................................................................................................... 28

5.1. Reference conditions 28 ....................................................................................................................................................

5.2. Characteristics 28 ..............................................................................................................................................................

5.3. Memory 29 .........................................................................................................................................................................

5.4. USB 30 ..............................................................................................................................................................................

5.5. Power supply 30 ................................................................................................................................................................

5.6. Environmental conditions 31 .............................................................................................................................................

5.7. Mechanical characteristics 31 ..........................................................................................................................................

5.8. Compliance with international standards 31 ......................................................................................................................

5.9. Electromagnetic compatibility (EMC) 31 ............................................................................................................................

6. MAINTENANCE ..................................................................................................................................................................... 32

6.1. Cleaning 32 .......................................................................................................................................................................

6.2. Replacement of batteries 32 ..............................................................................................................................................

6.3. Serial number 32 ...............................................................................................................................................................

6.4. Calibration log 33 ...............................................................................................................................................................

6.5. Embedded software version 33 .........................................................................................................................................

6.6. Updating the embedded software 33 .................................................................................................................................

7. WARRANTY ........................................................................................................................................................................... 35