Clarion CC-6500E Bruksanvisning

Clarion Dashcam CC-6500E

Läs nedan 📖 manual på svenska för Clarion CC-6500E (1 sidor) i kategorin Dashcam. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

Printed in Japan 2016/7 CC-6500E/CC-6600E 274-0630-12

Installation/Owner’s Manual

CC-6500E (WITH SHUTTER)

CC-6600E

HEAVY DUTY CMOS CAMERA

● Thank you very much for your purchase of this Clarion product.

● Read this "Installation and Instruction Manual" carefully to ensure correct and safe use.

Clarion Co., Ltd.

SAFETY PRECAUTIONS

When using this system, follow the precautions listed below.

WARNING

● Do not use this camera in any way other than vehicle installation.

This device is a vehicle-mounted rear view camera. Doing so may lead to a malfunction, fire,

electric shock or accident.

● Do not attempt to disassemble or modify the unit.

Never disassemble, modify or cut the cable covering to draw power from another device.

Doing so may lead to a malfunction, fire, electric shock or accident.

● Do not damage the cable.

Moisture or water may get inside the camera through the damaged part, resulting in

malfunction or fire.

● Never use the vehicle’s safety-related parts* for mounting or grounding the device.

* Nuts and bolts in the steering system, seat rails, brake system, tanks, etc.

Doing so may result in loss of control, fire or accident.

● Before making connections, disconnect the negative battery terminal.

Failure to do so may cause a short circuit, resulting in a malfunction, fire, electric shock or

accident.

● Route the cables avoiding high-temperature areas.

The covering of the cables may melt, causing a short-circuit and resulting in a malfunction,

fire or accident. Pay particular attention when routing the cables inside the engine

compartment.

● Installation and removal of the device should be requested to a professional service

engineer.

Doing so may lead to a malfunction, fire or accident. Contact the dealer where the device was

purchased.

● After completing installation and wiring work, check and make sure the vehicle’s

electrical equipment* is working properly.

* Brakes, lights, horn, hazard lamps, blinkers, etc.

Malfunctioning electrical equipment in the vehicle may lead to fire, electric shock or accident.

● For vehicles fitted with an auxiliary brake light, move the camera to the left or right

and mount it in a location where the auxiliary brake light can be seen fully.

If not, the auxiliary brake light may be obstructed, resulting in an accident.

● When mounting the camera outside a vehicle, mount it within the legally-stipulated

range.

A protruding camera may hit a passer-by and cause an accident.

● If installation of the device requires making a hole in the chassis, check the position of

the pipes, tanks, electrical wires, etc. and be sure to avoid interference or contact.

Damaged pipes or other parts may lead to a malfunction, fire or accident.

● Route and bundle the cables so that they do not interfere with driving operation.

If a cable coils round the steering column, gear lever, brake pedals, etc., it may lead to an

accident.

● Never drive looking solely at the monitor.

There is a limit in the range of the monitor image that can be captured as the camera is an

auxiliary device used for checking obstructions, etc. Actual distances and perceptions may

differ, so be sure to visually check safety while driving. Failure to do so creates the risk of

hitting a person or object in the camera’s blind spot, causing a serious accident.

● Discontinue use in the event of malfunction or abnormality.

If no image is displayed, smoke is emit ted or there is a strange smell, stop using the device

immediately and consult the dealer where it was purchased. Continued use may result in a

malfunction, fire, electric shock or accident.

● Do not pour water or place foreign objects inside the device.

If a foreign object or water gets inside the device, smoke or a strange smell is produced, or

any other abnormality occurs, stop using the device immediately and consult the dealer where

it was purchased. Continued use may result in a malfunction, fire, electric shock or accident.

● Reverse your vehicle at a slow speed.

This camera uses a wide-angle lens. The image captured may differ from the actual distance

so reversing the vehicle at a high speed may cause a collision with people or objects, resulting

in a serious accident.

CAUTION

● Follow the instructions in the manual when mounting and connecting the device.

Incorrect connection may result in a malfunction, fire or accident.

● After mounting the device, check that the monitor image is a mirror image (same

image as the rear mirror).

Incorrect setup may mean that the monitor image is not horizontally flipped, resulting in

accident.

● Be sure to use the accessories and specified parts.

Using components other than those specified may lead to damage or detachment of the

camera, resulting in them becoming detached and leading to a malfunction, fire or accident.

CAUTION

● After wiring the various cables, secure them with clamps and/or insulating tape.

If the cables come into contact with the chassis, they will fray and short-circuit, leading to a

malfunction, fire or accident.

● If a hole is made in the chassis to route the cables, use protective tubing or insulating

grommet.

If the cables come into contact with the openings, they will fray and short-circuit, leading to

an accident or fire.

● If a hole is made in the chassis for mounting or cable routing purposes, seal the gap in

the hole and the gap between the hole and the cable with silicon adhesive or similar.

If exhaust gas or water gets inside the vehicle through the gap, it may result in an accident.

● Route the cables so that they do not get caught in the chassis, screws, seat rails or

other moving parts.

Damaged or short-circuited cables may result in a malfunction, fire, electric shock or

accident.

● Do not subject the equipment to strong impacts e.g. by dropping or hitting it etc.

Doing so may lead to a malfunction or fire.

● If screws are used to mount the device, be sure to tighten them securely.

Loose screws may result in a malfunction or accident.

● Do not use the camera underwater.

If used underwater, water may get inside the camera, resulting in a malfunction, electric

shock or accident.

● After mounting the camera, do not subject it to strong impacts e.g. by hitting it etc.

The mounting angle may change, resulting in a normal image not being captured. In addition,

this device utilises precision electronic parts. Subjecting it to shock may result in malfunction,

fire or electric shock.

● Do not spray high-pressure water onto the camera when washing the vehicle with a

high-pressure washing machine.

Detachment of the camera or loosening of the screws may result in damages or malfunctions.

Moreover, if water gets inside the camera, it may result in a malfunction, fire or electric shock

● Check the mounting screws occasionally and tighten any that have come loose.

This camera may get detached and drop off due to loosening of the screws, resulting in

contact with pedestrians and accidents.

● The monitor image of this camera is inverted left to right just like the rear view mirror

of your vehicle. In addition, note that the field of vision may also differ depending on

the vehicle.

PRECAUTION

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to consult the dealer or an

experienced radio/ T V technician for help.

■INFORMATION FOR USERS:

CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL

VOID THE WARRANT Y AND WILL VIOLATE FCC APPROVAL.

PACKAGE CONTENTS

This device consists of the following components.

In the event of any defect, contact the retailer where it was purchased.

1 Installation/Owner’s manual

(This Booklet) 1 .......................................................

2 Main camera unit 1 ................................................

3 Mounting bracket 1 ................................................

4 Camera cover 1 .....................................................

5 Grommet ............................................................ 1

Accessory bag 1 ...............................................

6 Hexagon head bolts with built-in washer

(M4 mm x 10 mm)

(for installing on the main unit) 4 ............................

7 M4 bush (for installing on the main unit) 4 .............

8 Hexagon head bolts with built-in washer

(M5 mm x 20 mm) (for installing on the vehicle side) 2 ...................................................................

9 Flanged nuts (M5 mm) (for installing on the vehicle side) 2 .............................................................

SPECIFICATIONS

CC6500E

(with attached shutter) CC6600E

Power supply

voltage*

Camera power supply DC 9.0 V

Shutter drive power

supply DC 12 V —

Current

consumption

Camera power supply 50 mA or less

Shutter drive power

supply 300 mA or less —

Image sensor 1/3.7 inch 0.33 million pixel CMOS

Angle of view Horizontal 118° / Vertical 97.8°

Weight 180 g (including cable) 140 g (including cable)

Main body external dimensions 77 (W) × 38 (H)

× 55 (D) mm

77 (W) × 38 (H)

× 51.4 (D) mm

* Use only the power supplied by the special camera EUC box or monitor. Never connect to and supply

power directly from a power supply line such as the vehicle battery etc.

77 mm

38 mm

55 mm 77 mm

38 mm

51.4 mm

CC6500E (with attached shutter) CC6600E

Shutter Surface glass area

Declarationof conformity

We Clarion declares that the product CC6500,CC6600 is following the provisions of Directive

2014/30/EU and Directive 2011/65/EU.

Authorized Representative

Clarion Europe S.A.S.

244 rue du Pré à Varois, 54670 Custines, France

Telephone: +33 3 83 49 44 00 Fax: +33 3 83 24 17 62

HOW TO INSTALL

Installation Precautions

●

Be sure to use the supplied bolts to mount the bolts to the

camera. If any bolts are lost when mounting the camera,

be sure to use M4 mm x 10 mm hexagon head bolts with

built-in washer. Do not under any circumstances use bolts

longer than this. To ensure watertightness, the bolt stoppers

in the camera case have a bag structure. Use of long bolts

may damage the screw thread and camera main body,

compromising watertightness

●

Never swing the camera by the cable or pull the cable. Doing

so may impair the camera's watertightness or break the

cable, resulting in malfunction.

●

Avoid mounting the camera where the surface glass area is

easily stained by mud splashes, exhaust fumes, etc

Installation Precautions

10 mm

M4 x 10 mm

Hexagon head bolts with

built-in washer

(M4 mm x 10 mm)

(camera mounting bolts)

Drill camera mounting holes ( 5.5 mm) at 2 locations, and cable routing

holes (14 mm if the enclosed grommet is used) on the chassis end.

To prevent camera shake, make a hole in a strong part and mount the camera. If the part is not

strong enough, carry out appropriate reinforcement.

Fix the mounting bracket securely to the chassis using the enclosed bolts and

flange nuts. (2 locations)

Secure the camera main body temporarily to the mounting bracket using the

enclosed bolts and bushes. (2 locations on the left and right)

Never secure the camera to the mounting bracket on the right or left side only.

Hexagon head bolts with built-in

washer (M5 mm x 20 mm)

Hexagon head

bolts with built-in

washer (M4 mm

x 10 mm)

* Take note of the

bolt length

6 Hexagon head

bolts with built-in

washer (M4 mm

x 10 mm)

* Take note of the

bolt length

2 Main camera unit

Camera cover

7 M4 bush

3 Mounting bracket

To A1

To A2 To B2

To B1

9 Flanged nuts

(M5 mm)

Pitch dimension of installation holes

= 29 mm - 47 mm

Vehicle side :

Installation holes (5.5mm)

See “WIRING AND CONNECTIONS” for the wiring instructions.

After connecting the cables, mount the camera and

adjust the angle so that the rear bumper or back

end of the vehicle appears in the monitor. (See

diagram on the right)

After adjusting the mounting angle of the camera,

fully tighten the bolts to secure the camera main

body properly.

Be sure to use a sealing material (e.g. a sealant

etc.) on the mounting holes, screws and cable

routing holes on the chassis for water-proofing and rust-proofing.

■Mounting example

Installation example

on a horizontal surface

(mounting angle 46°)

56 mm

57.8 mm

67.3 mm

12.6 mm

1.1 mm

3 mm

25 mm

76.5 mm

76.5 mm 67 mm

46°

5.4 mm

44°

Installation example-1

on a vertical surface

(mounting angle 44°)

Installation example-2

on a vertical surface

(mounting angle 44°)

WIRING AND CONNECTIONS

Wiring Precautions

●

Disconnect the negative terminal of the battery before connecting

the cables. Failure to do so may cause a short circuit, resulting in a

malfunction, fire, electric shock or accident

●

Lay the relay cable inside the vehicle so as to prevent it from

getting damaged. If you have to lay the cable outside the vehicle,

make sure it is securely fastened to the chassis in order to preven

it from flapping and getting caught by tree branches etc. In addition, besides ensuring that the

connectors are connected properly, install the camera in a location where water will not splash

onto it.

●

When wiring the cables, as far as possible keep them away from hot areas such as the engine

exhaust pipe, transmission, etc., rotating parts such as the cooling fan, alternator, etc., and noise

generating sources, and cover them with a corrugated tube before securing with clamps etc

●

Never cut the cables as they are special cables with built-in coaxial lines

●

When bake painting the vehicle, be sure to wire the cables only after the painting

●

Use a protective tube or the enclosed grommet etc. to

protect the metallic parts of the routing holes, cross

sections of the metal plate and parts of the cables that

are easily cut. In addition, lay the cables without damaging

them such as by twisting or bending them strongly as this

will result in internal short-circuiting. Be careful not to

scratch the outer skin as this will damage the waterproof

property

●

For the power supply (camera power / shutter drive

power), use only the power supplied by the special EUC

box or monitor. Never supply power directly by connecting to a power supply line such as the

vehicle battery as this will result in a malfunction, fire, electric shock or accident due to an over-

voltage or over-current

Wiring Precautions

■Wiring example

Special waterproof

relay cable

(sold separately)

Connect the connectors properly.

Car Exterior

Car Interior

5Grommet (with notch)

Connect to the special camera ECU box or monitor.

■Connection procedure for special waterproof relay cable (sold separately)

Align the arrow mark on the relay cable to the

 mark on the camera cable

to insert the connector.

Pull the cable lightly to make sure that the connector is locked properly.

 mark on the camera cable

Do not pull or bend the connected part with a force of 30 N or higher.

The connector may be damaged if an excessive load is applied.

Arrow mark on the relay cable

CLEANING THE CAMERA

●Do not use benzine, thinner, or alcohols.

●Do not wipe the camera with a cleaner that contains polishing powder etc. This may result in scratches

on the camera.

●If the surface glass area is stained, wipe lightly with a soft and wet cloth etc. Scratches may occur if

you rub the camera strongly with a dry cloth.

●If the surface glass area is stained, you can clean it by opening and closing the shutter with your hands.

When you open and close the shutter by hand, the shutter may not close completely sometimes. In this

case, operate the shutter to return it to the original position.

TROUBLESHOOTING

The following situations may not be malfunctions. Check the following one more time before sending the

camera for repair. Contact the dealer where the product was purchased if you have any questions or if

you still cannot resolve the problem.

Symptom Possible reasons Remedy

There is no image Check the connections and connect the Incomplete wiring

camera correctly.

Image quality is bad Surface glass area is stained Wipe lightly with a soft and wet cloth etc.

Note that scratches may occur if you rub

the camera strongly with a dr y cloth.

The lens is exposed to sunlight

or the headlight from another

vehicle

The camera will return to normal if the

light shining on the lens disappears.

Surrounding is too dark Image quality deteriorates at night or in

dark places. The image returns to normal

when it brightens up.

Shutter does not open The area is constricted by

obstructions such as rubbish

etc.

Remove the obstructions. Note that the

shutter may be damaged if the obstruction

is removed unreasonably then.

Snow, ice, etc. is stuck to the

camera

Melt the snow, ice, etc., first before use.

2 3

4 5

6 7 98

Rear bumper or

rear end of the vehicle

approx. 7 mm

Monitor screen

English

Produktspecifikationer

Varumärke:	Clarion
Kategori:	Dashcam
Modell:	CC-6500E
Färg på produkten:	Zwart
Husmaterial:	Metaal
Monteringsmetod:	Muur
Lämplig för skärmstorlekar:	- "
Maximal viktkapacitet:	60 kg
Kompatibilitet:	LED/LCD/Plasma
Kompatibilitet med monteringsgränssnitt (min):	800 x 400 mm
Kompatibilitet med monteringsgränssnitt (max):	800 x 400 mm
Maximal skärmstorlek:	80 "
Minsta skärmstorlek:	- "