Control4 CA-1 Bruksanvisning

Control4 övervakningskamera CA-1

Läs nedan 📖 manual på svenska för Control4 CA-1 (2 sidor) i kategorin övervakningskamera. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

Supported model

• C4-C A1 Automation Controller, CA-1

Introduction

The Control4® CA-1 Automation Controller enables control of lights, security

systems, sensors, door locks, and other devices controlled by IP, Zigbee, Z-Wave®,

or serial connections. The controller has a fast processor, external antennas for Wi-

Fi and Zigbee® radios, an internal slot for a Z-Wave™ module (sold spearately), and

can be powered by PoE. This controller is perfect for home, apartments, and other

installations that do not require IR control or audio streaming.

After you install and conﬁgure the controller with other Control4 devices, your

customers can control their system using the Control4 apps, system remote

controls, touch screens, or other Control4-supported interface devices (sold

separately).

Box contents

• CA-1 Automation Controller

• External power supply with international plug adaptors

• Antennas (2)

Accessories available for purchase

• Z-Wave Module - Region H (C4-ZWH)

• Z-Wave Module - Region U (C4-ZWU)

• Z-Wave Module - Region E (C4-ZWE)

Warnings

Caution! To reduce the risk of electrical shock, do not expose this

apparatus to rain or moisture.

AVERTISSEMENT ! Pour réduire le risque de choc électrique, n’exposez

pas cet appareil à la pluie ou à l’humidité.

Caution! In an over-current condition on USB, the software disables

the output. If the attached USB device does not appear to power on,

remove the USB device from the controller.

AVERTISSEMENT ! Dans une condition de surintensité sur USB le

logiciel désactive la sortie. Si le périphérique USB connecté ne semble

pas s’allumer, retirez le périphérique du contrôleur.

For more information, visit the Products pages at dealer.control4.com.

Requirements and speciﬁcations

Note: We recommend using Ethernet instead of Wi-Fi for the best

network connectivity.

Note: The Ethernet or Wi-Fi network should be installed before starting

the CA-1 controller installation.

Note: The software required to conﬁgure this device is Composer Pro.

See the (Composer Pro User Guide ctrl4.co/cpro-ug) for details.

Speciﬁcations

Model number C4-CA1

Connections

Network Ethernet—10/100BaseT compatible (required for controller

setup)

Wireless Wireless N (2.4GHz, 802.11n/g/b)

Wireless security WEP, WPA, and WPA2

Wireless antenna External reverse SMA connector

Zigbee Pro 802.15.4

Zigbee antenna External reverse SMA connector

USB port 2 USB 2.0 ports-500mA

Serial out 1 serial out RJ45 port (RS-232)

Z-Wave Integrated Z-Wave slot accepts Control4 Z-Wave modules

(sold separately)

Music services Requires Triad One for audio output. Does not support

Spotify Connect, ShairBridge, or My Music scanning.

Power

Power requirements 5VDC 3A, external power supply included

Power supply AC power supply accepts 100-240V ~ 50-60 Hz (0.5A)

PoE 802.3af (<13 W)

Power consumption Max 15W (51 BTU/hr)

Miscellaneous

Operating temperature 32˚ - 104˚ F (0˚ - 40˚ C)

Storage temperature 4˚ - 158˚ F (-20˚ - 70˚ C)

Dimensions (L x W x H) 5.5" 5.5" 1.25" (14 × 14 × 3.8 cm) × ×

Weight 0.65 lb (0.3 kg)

Shipping weight 1.5 lb (0.68 kg)

Additional resources

The following resources are available for more support.

• Control4 Knowledgebase: kb.control4.com

• Dealer Forums: forums.control4.com

• Control4 Technical Support: dealer.control4.com/dealer/support

• Control4 website: www.control4.com

• Composer Pro documentation in online help or PDF format available on the

Dealer Portal under Support: ctrl4.co/docs

• Z-Wave documentation: ctrl4.co/z-wave

Front view

A Status LED—The RGB status LED gives system status feedback. See

“Troubleshooting” in this document for LED status information.

B Z-Wave port—Removable plastic cover on top of the controller with a Z-Wave

port underneath for a Control4 Z-Wave module.

4 Connect the power cord to the controller’s power port and then into an

electrical outlet (if the controller is not powered by PoE).

Connecting the serial port (optional)

The controller includes one RJ-45 serial port that can be conﬁgured for RS-232

serial communication.

The following serial communication conﬁgurations are supported:

• RS-232—Hardware ﬂow control, up to 115,200 Kbps.

(TXD, RXD, CTS, RTS, GND)

To set up the serial port:

1 Connect a serial device to the controller using Cat5/Cat6 cable and an RJ-45

connector.

Important: The serial port pinout follows the EIA/TIA-561 serial wiring

standard. Use the wiring shown in the diagram below. Many pre-built

DB9 to RS-232 cables, including network switch console cables, will not

work.

2 To conﬁgure the serial port settings, make the appropriate connections in

your project using Composer Pro. See the Composer Pro User Guide for

details.

Note: Serial settings are deﬁned in the device driver in Composer. Serial

settings (baud, parity, and serial port type) are automatically conﬁgured

when a device driver is connected in Composer Pro to the serial port

connection of the CA-1 driver.

Serial port pinout and wiring recommendation

9 8 7 6

1234

Pin 4 SG

Pin 5 RXD

Pin 6 TXD

Pin 7 CTS

Pin 8 RTS

Pins 1-3 not used

EIA-561 wiring recommended

DB9 rear view

RS-232 pinout

Back view

A Zigbee—External antenna connector for Zigbee radio.

B Power port—Power connection for external power supply.

C ETHERNET (PoE)—RJ-45 port for 10/100BaseT Ethernet network connection.

Network connection used for conﬁguration and device control. Supports PoE.

D SERIAL—RJ-45 port for serial communications. Can be used for RS-232

communication for device control.

E USB—Two USB 2.0 ports for external USB drives (e.g., FAT32-formatted

devices). See “Setting up external storage devices” in this document.

F ID / RESET buttons—Buttons used to identify the device in Composer Pro and

reset the controller. See “Troubleshooting” in this document.

G Wi-Fi—External antenna connector for 2.4 GHz 802.11n/g/b Wi-Fi radio. Wi-Fi

connection can be used for device control, but controller must have a wired

connection for initial setup.

Installing the controller

Requirements:

• Ensure that the home network is in place before starting system setup.

• A wired connection to the network is required for initial controller setup.

• The controller requires a network connection (Ethernet is recommended or

Wi-Fi) to use all of the features as designed. When connected, the controller

can communicate with other IP devices in the home and access Control4

system updates.

• Composer Pro software version 2.10.0 or newer is required for conﬁguration.

Mounting options:

• On-wall—The controller can be mounted to the wall using screws. Remove

the rubber feet, measure the distance between them, and insert 2 screws into

the wall so that the heads are about 1/4 to 1/2 inch from the wall. Position

the holes on the back of the controller over the screw heads and slide the

controller onto the screws.

• DIN rail—The controller can be mounted to the wall using a section of DIN rail

channel. Mount the rail to the wall, and then attach the controller to the rail.

Important: The CA-1 is not rated to be installed inside an electrical

panel. DIN-rail installation is only intended for a wall-mount or other

section of DIN rail outside of an electrical panel.

Connecting the controller

1 Connect the controller to the network.

• Ethernet—To connect using an Ethernet connection, plug the data cable

from the home network connection into the controller’s RJ-45 port

(labeled “Ethernet”) and the network port on the wall or at the network

switch.

• Wi-Fi—To connect using Wi-Fi, ﬁrst connect the unit to Ethernet, attach

the Wi-Fi antenna to the controller, and then use Composer Pro System

Manager to reconﬁgure the unit for Wi-Fi.

2 Attach serial devices as described in “Connecting the serial port.” Serial

port is only used for controlling external devices, the controller must be

connected over Ethernet or Wi-Fi to set up the Control4 programming.

3 Connect any external storage devices (USB) as described in “Setting up

external storage devices” in this document.

BA C D E F G

CA-1 Automation Controller

Installation Guide

Snap AV and their respective logos are registered trademarks or trademarks of

Wirepath Home Systems, LLC, dba “Control4” and/or dba “SnapAV” in the United States

and/or other countries. 4Store, 4Sight, Control4 My Home, Snap AV, Mockupancy, Neeo,

OvrC, Triad, and Wirepath are also registered trademarks or trademarks of Wirepath

Home Systems, LLC. Other names and brands may be claimed as the property of their

respective owners. All speciﬁcations subject to change without notice.

Installing a Z-Wave module (optional)

An optional Z-Wave module can be added to the Z-Wave port on top of the

controller. Z-Wave Modules are speciﬁc to your region. See the Z-Wave Setup

Guide for software conﬁguration and more information (ctrl4.co/z-wave-sg)

To install the a Z-Wave module into the controller:

Important: Power o the controller before you install the Z-Wave Module.

1 Using a small ﬂathead screwdriver, remove the small plastic cover on top of

the Z-Wave module.

4 Replace the plastic cover.

Setting up external storage devices

You can store and access media from an external storage device, for example, a

network hard drive or USB memory device, by connecting the USB drive to the

USB port and conﬁguring the media in Composer Pro.

Note: Media scanning is not supported on the CA-1 controller.

Note: We support only externally-powered USB drives or solid state

USB sticks. USB-powered external hard drives are not supported.

Note: When using USB storage devices with the CA-1 controller you can

only use one partition with a 2TB maximum size. This limitation applies

to USB storage devices with all other controllers also.

Composer Pro driver information

Use Auto Discovery and SDDP to add the driver to the Composer project. See the

Composer Pro User Guide for details.

Note: A CA-1 controller may only run as Director in a single-controller

project. CA-1 controllers may be used as secondary controllers in

projects with other controllers that can be a Director in a multiple-

controller project.

Note: The CA-1 controller requires OS 2.10.1 or higher.

Connecting Z-Wave and Zigbee devices

All software conﬁguration including connecting Zigbee and Z-Wave devices is

done with Composer Pro. See the for more information.Composer Pro User Guide

Troubleshooting

Reset to factory settings

Caution! The factory reset process will remove the Composer project.

Note the location of the con-

Orient the Z-Wave module to

3Orient the Z-Wave

module to ﬁt in the port

opening, hold it by the

tab on top of the module,

and insert it straight

down into the port.

Note the location of the connector on

the Z-Wave port and the location of

the connector on the Z-Wave module.

To restore the controller to the factory default image, perform the following

steps:

1 Insert one end of a paper clip into the small hole on the back of the

controller labeled .RESET

2 Press and hold the button, the controller will reset and the Status LED RESET

will go solid red.

3 Hold the button until the LED blinks double yellow. This should take ﬁve to

seven seconds. The LED will blink yellow while the factory restore is running.

When complete, the LED will turn o and the device will reset to complete

the factory restore process.

Power cycle the controller

Press and hold the button for ﬁve seconds. The controller will restart.ID

Reset the network settings

To reset the controller network settings to the default, follow these steps:

1 Disconnect power to the controller.

2 While pressing and holding the button on the back of the controller, ID

power on the controller.

3 Hold the button until the LED is solid orange, then immediately release ID

the button.

4 If during the boot sequence the LED stays orange, press and hold the ID

button until the LED blinks blue, and then release it.

LED troubleshooting guide

LED legend: = solid = ﬂashing (4 Hz)

(Hz = ﬂashes a

second)

= ﬂashing (1 Hz) = ﬂashing (1/2 Hz)

Status LED

Power up No IP address

Controller is booting Controller is updating

Reset check Update error

Boot complete Factory restore in progress

Connected to Director (link) Factory restore error

USB over-current detected

Regulatory/Safety information

To review regulatory information for your particular Control4 products, see the

information located on the Control4 website at ctrl4.co/reg.

Warranty

Visit ctrl4.co/warranty for details.

More help

For the latest version of this document and to view additional materials, open the

URL below or scan the QR code on a device that can view PDFs.

200-10001-B

2020-9-9 DH

MOST RECENT VERSION

ctrl4.co/ca1-ig

MORE INFO ON CA CONTROLLERS

ctrl4.co/ca

Produktspecifikationer

Varumärke:	Control4
Kategori:	övervakningskamera
Modell:	CA-1

Behöver du hjälp?

Om du behöver hjälp med Control4 CA-1 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

övervakningskamera Control4 Manualer

Control4 CA-1 Bruksanvisning

22 September 2024

övervakningskamera Manualer

Nyaste övervakningskamera Manualer

Speco Technologies WDRB11H Bruksanvisning

27 Oktober 2024

Vivotek AI-108 Bruksanvisning

27 Oktober 2024

Acti E88 Bruksanvisning

27 Oktober 2024

Yale WIPC-303W Bruksanvisning

27 Oktober 2024

Grandstream GXV3611IR_HD Bruksanvisning

27 Oktober 2024

Airlive DM-720 Bruksanvisning

27 Oktober 2024

Speco Technologies O8B7M Bruksanvisning

27 Oktober 2024

Grandstream GXV3615W Bruksanvisning

27 Oktober 2024

Vivotek IP8133 Bruksanvisning

27 Oktober 2024

Olympia OC 1280P Bruksanvisning

27 Oktober 2024