CyberData Systems 011324 Bruksanvisning

CyberData Systems mottagare 011324

Läs nedan 📖 manual på svenska för CyberData Systems 011324 (3 sidor) i kategorin mottagare. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/3
Quick Start Guide 931155B
The IP Endpoint Company
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick
Reference placemat.
1.2. Download the current manual, otherwise known as an Operations Guide,
which is available in the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011324/
Note You can also navigate to the Downloads tab by going to
www.CyberData.net and following the steps that are indicated by
the following figures:
2.0 Select Power Source
IEEE 802.3af or 802.3at PoE Switch IEEE 802.3af or 802.3at PoE Injector
Set PoE power type to Class 0 = 15.4W
OR
for high power PoE+ set Class 4 = 30W
CAT6 cable recommended—
for longer distances
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
Set port to full duplex/ 100mbps
Spanning Tree Protocol (STP) must be disabled or Portfast enabled
1
34
2
SIP
OUR PRODUCTS
VOIP PRODUCTS
A
B
011324 SIP PAGING AMPLIFIER Downloads
SIP Paging Amplifier
Quick Start Guide
Quick Start Guide 931155B
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity on the front of
the device during the initialization process. See the following figure:
3.2. The Power (Pwr) LED is GREEN for 802.3af and is BLUE for 802.3at. The
GREEN Status LED and the GREEN Power (Pwr) LED come on
immediately. The Speed (SPD) LED illuminates AMBER for a 100Mb link or
is off for 10MB when the network link to the device is established. The Link/
Activity LED blinks to indicate network traffic.
After about 20 seconds, the GREEN Status LED will blink fast to indicate
that the device is acquiring an IP address and attempting to autoprovision.
It will turn off thereafter until the device has finished booting. When the
device has fully booted, the GREEN Status LED will turn on solid.
If there is no DHCP server available on the network, it will try 12 times for 60
seconds and eventually fall back to the programmed static IP address (by
default 10.10.10.10) or the previously used DHCP address if a prior lease
was established. This process will take approximately 80 seconds.
3.3. When the device has completed the initialization process, press and hold
the RTFM switch for 3 seconds to announce the IP address.
This concludes the power test. Go to Section 4.0, "Connecting to a Network
in a Test Environment".
SPD
PWR
Link/Act
Status
Volume
Power (Pwr) LED
( )BLUE/GREEN
Speed (SPD) LED
(AMBER) (100Mb)
Link/Activity (Link/Act.) LED
( )GREEN
Status LED
( )GREEN
Quick Start Guide 931155B
4.0 Connecting to a Network in a Test Environment
Note The following connections are usually needed for this procedure:
• Computer
• PoE switch or injector
• CyberData device
4.1. In a test environment, use a computer that is connected to the same switch
as a single CyberData device. Note the subnet of the test computer.
4.2. Use the CyberData Discovery Utility program to locate the device on the
network. You can download the Discovery Utility program from the following
link:
https://www.cyberdata.net/pages/discovery
4.3. Wait for initialization to complete before using the Discovery Utility program
to scan for a device. The device will show the current IP address, MAC
address, and serial number.
4.4. Select the device.
4.5. Click Launch Browser. If the IP address is in a reachable subnet from the
computer that you are using to access the device, the Discovery Utility
program should be able to launch a browser window pointing to the device’s
IP address.
4.6. Log on to the web interface by using the default username (admin) and
password (admin) to configure the device.
4.7. Perform an audio test by pressing the Test Audio button that is located at
the bottom of the Device Configuration page. If the audio test message is
clearly audible, then your CyberData device is functioning properly.
4.8. The device is now ready to be set for your desired network configuration.
You may search the Compatible IP-PBX Servers index for available
sample VoIP phone system configurations and set up guides at the following
website address:
https://www.cyberdata.net/pages/connecting-to-ip-pbx-servers

Produktspecifikationer

Varumärke: CyberData Systems
Kategori: mottagare
Modell: 011324

Behöver du hjälp?

Om du behöver hjälp med CyberData Systems 011324 ställ en fråga nedan och andra användare kommer att svara dig


mottagare CyberData Systems Manualer

CyberData Systems

CyberData Systems 011407 Bruksanvisning

20 September 2024
CyberData Systems

CyberData Systems 011324 Bruksanvisning

16 September 2024
CyberData Systems

CyberData Systems 011404 Bruksanvisning

16 September 2024
CyberData Systems

CyberData Systems 011405 Bruksanvisning

16 September 2024

mottagare Manualer

Nyaste mottagare Manualer

Alto

Alto D1 Bruksanvisning

16 Januari 2025
Alto

Alto MC700.4 Bruksanvisning

16 Januari 2025
Alto

Alto MC250.4 Bruksanvisning

16 Januari 2025
Alto

Alto MC250.8 Bruksanvisning

16 Januari 2025
Alto

Alto D4 Bruksanvisning

16 Januari 2025
Alto

Alto D3 Bruksanvisning

16 Januari 2025
Alto

Alto MC500.4 Bruksanvisning

16 Januari 2025
S.M.S.L

S.M.S.L PA200 Bruksanvisning

15 Januari 2025
Peavey

Peavey CKd 608 Bruksanvisning

15 Januari 2025
Wavtech

Wavtech link700.4plus Bruksanvisning

14 Januari 2025