Da-Lite Cinema Contour 87157V Bruksanvisning

Da-Lite Projektionsduk Cinema Contour 87157V

Läs nedan 📖 manual på svenska för Da-Lite Cinema Contour 87157V (8 sidor) i kategorin Projektionsduk. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/8
INSTRUCTION BOOK FOR
Cinema Contour® Screen
2
High Power® Frame Bracket
Screens with High Power® quantity = 2
Screens with 2-piece side frame rails quantity = 2
Quantity Included ___________________________
Included Hardware
Frame Assembly
1. Unwrap the frame pieces. Assemble frame pieces on padding
material or other soft, clean surface. This will help keep the
frame clean and protect it from scratches.
2. Slide the frame pieces together at corners (Note: Frame
assembly holes may not appear toit properly at the corners
until all fasteners have been attached. Once fasteners are
attached, the frame corners will be drawn in for a properit.)
Secure frame pieces with #10 screws provided. Do not tighten
screws until all are started, then tighten. See Figure 1.
NOTE: The frame pieces are labeled “top” and “bottom”. Be
sure the frame pieces are assembled according to the labels.
This will ensure the snap pattern on the frame and screen
surface will match.
3. Attach the eight snap studs to the back of the frame in the
predrilled holes.
Figure 1 (Rear View)
Large Wall Bracket (47" Long)
Installation screws not included
Quantities vary by screen size:
Screens 80" and smaller viewing width = 1
Screens over 80" to 96" viewing width = 2
Screens over 96" viewing width = 3
Quantity Included ___________________________
Small Wall Bracket (8" Long)
Installation screws not included
Quantity = 1. Only for screens 80" and smaller viewing width.
Quantity Included ___________________________
Snap Stud
Quantity Included ___________________________
#10 Screw
Quantity Included ___________________________
Use Installation Method Number ____________
Screws
Snaps
3
Installation
Method 1 (Screens 80" And Smaller
In Viewing Width)
Method 1 (Screens 80" And Smaller
In Viewing Width)
There are four methods of installation based on the size of the
screen and type of viewing surface. Measure the width of the
viewing area of your screen and refer to the appropriate method
of installation below. The wall bracket diagram shows the type
and quantity of bracket(s) supplied based on the size of the
screen.
Method 1: Screens 80" and smaller in viewing width.
Method 2: Screens over 80" up to 96" in viewing width.
Method 3: Screens over 96" in viewing width.
Method 4: Any size screen with High Power® viewing surface.
1. Secure the wall bracket to wall studs at the desired height.
Make sure the bracket is level. The top of the frame will be
1/8" above the top of the wall bracket when mounted. You will
need at least 5/8" clearance above the bracket to hang the
screen. Figures 2, 3, and 4 show the proper orientation for the
supplied wall brackets.
2. To install the lower wall bracket, you must measure the
overall height of the screen frame and subtract 1-3/8". Using
that dimension, measure down from the top edge of the wall
bracket and mark the wall for two screw holes. The holes
should be centered within the frame and 6" apart. Refer to
Figure 3.
3. Attach the small wall bracket to the wall. Refer to Figure 4 for
proper orientation. Do not tighten the screws completely. The
bracket should slide up and down easily.
4. Unroll the screen on a clean surface. Do not use newspaper.
The viewing side is rolled to the inside of the roll. Place the
frame over the screen surface, and while lifting the frame
with one hand, snap the screen surface onto the frame
with the other hand while maintaining a steady pull
on the surface.
5. Hang the screen on the brackets by hooking the bottom of
the frame onto the lower wall bracket and lift up until you can
hook the top of the frame on the top bracket. Push down on
the frame to seat it on the brackets. Refer to Figure 4.
Figure 2
Small Wall Bracket
1-Piece
Figure 3
Large Wall
Bracket
1-Piece
Large Wall Bracket
6"
Small Wall Bracket
Overall Height Less 1 ⅜"
Overall
Height
Figure 4
2
Lift
1
3
Wall

Produktspecifikationer

Varumärke: Da-Lite
Kategori: Projektionsduk
Modell: Cinema Contour 87157V

Behöver du hjälp?

Om du behöver hjälp med Da-Lite Cinema Contour 87157V ställ en fråga nedan och andra användare kommer att svara dig


Projektionsduk Da-Lite Manualer

Da-Lite

Da-Lite Designer Manual 76456MO Bruksanvisning

6 Oktober 2024
Da-Lite

Da-Lite Cinema Vision Bruksanvisning

2 Oktober 2024
Da-Lite

Da-Lite Model C 83401 Bruksanvisning

29 September 2024
Da-Lite

Da-Lite Model B Bruksanvisning

27 September 2024
Da-Lite

Da-Lite Perm-Wall 78676 Bruksanvisning

26 September 2024
Da-Lite

Da-Lite Model C With CSR Bruksanvisning

25 September 2024
Da-Lite

Da-Lite Dual Format Imager 38063EV Bruksanvisning

11 September 2024
Da-Lite

Da-Lite DescenderPro 29788LS Bruksanvisning

5 September 2024
Da-Lite

Da-Lite 88629 Bruksanvisning

29 Augusti 2024
Da-Lite

Da-Lite Ascender Electrol 84766E Bruksanvisning

21 Augusti 2024

Projektionsduk Manualer

Nyaste Projektionsduk Manualer

Optoma

Optoma DS-3120PMG Bruksanvisning

11 Oktober 2024
Optoma

Optoma DS-9120PMG Bruksanvisning

29 September 2024
EPV

EPV PGF106WH1-A4K Bruksanvisning

25 September 2024
EPV

EPV PGF84WH1 Bruksanvisning

25 September 2024
KHOMO GEAR

KHOMO GEAR GER-1252 Bruksanvisning

23 September 2024
KHOMO GEAR

KHOMO GEAR GER-1273 Bruksanvisning

23 September 2024
Celexon

Celexon Ultramobile Plus Professional 194 x 146 Bruksanvisning

22 September 2024
Celexon

Celexon Statief Economy (4:3) 176 x 132 Bruksanvisning

22 September 2024
Celexon

Celexon Economy (4:3) 158 x 118 Bruksanvisning

22 September 2024
Celexon

Celexon Ultramobil Professional Bruksanvisning

22 September 2024