Da-Lite Large Advantage Deluxe Electrol 36861 Bruksanvisning
Da-Lite
Projektionsduk
Large Advantage Deluxe Electrol 36861
Läs nedan 📖 manual på svenska för Da-Lite Large Advantage Deluxe Electrol 36861 (8 sidor) i kategorin Projektionsduk. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/8
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com
The Da-Lite Difference.
Instruction Book for
LARGE ADVANTAGE® DELUXE ELECTROL®
PRE-INSTALLATION
1
CASE INSTALLATION
1. The case provides multiple attachment points for bolts, cables, or threaded rod. Page 5 shows threaded rod
installed. The variable position-mounting bracket may be located anywhere along the length of the case. It is
recommended to keep the brackets spaced evenly enough to distribute the weight of the screen. One mounting
bracket is required for every 4' of case length.
The case has a self-trimming flange around the bottom. Ceiling tiles or drywall may be placed on top of this flange
to provide a finished appearance.
2. After securing the case in the ceiling check that the case is level and plumb.
3. Install electrical connections that apply to your unit. Review the wiring diagrams on page 4 for proper installation.
1. Carefully unpack screen and remove outer wrapping from case.
2. Make sure to recheck measurements of screen location before installation.
Please Note: Motor Operator Projection Screen Models LADT, LADDT, LAD
and LADD must be installed in accordance with the requirements of the
Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA C22.1
and the National Electric Code (NEC), NFPA 70. An appropriate disconnect
device shall be provided as part of the building installation.
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions should always be followed, including the
following:
1. Read and understand all instructions before using.
2. Close supervision is necessary when any appliance is used by or near children. Do not leave
appliance unattended while in use.
3. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged –
until it has been examined by a qualified serviceman.
4. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
5. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance
should be used. Cords rated for less amperage than the appliance may overheat.
6. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
7. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized
service dealer when repair work is required. Incorrect reassembly can cause electric shock when
the appliance is used subsequently.
8. The use of an accessory attachment not recommended by the manufacturer may cause a risk of
fire, electric shock, or injury to persons.
SAVE THESE INSTRUCTIONS
BOLTS
ACCESS
DOOR
FIGURE 1
DOOR SUPPORT SCREWS
(NOT ALL SIZES)
2
If your screen was shipped with the motor and roller already installed proceed to step 7.
1. Remove four bolts from ends of door assembly (2 bolts on each end) (Fig. 1). This will allow the door assembly to
drop open for access to case. For larger sizes, you will also need to remove the door support screws.
2. Carefully unpack screen and roller assembly. Leave packing paper on the roller.
3. Remove the square peg bracket from the motor end of the roller assembly.
4. Remove the safety clip from the motor attachement bracket located in the motor end of the screen housing.
5. Place the roller assembly into the case with the motor on the left side. The limit switches should be facing down.
Line up the head of the motor with the motor attachment bracket.
6. Loosen four bolts that secure pin end mounting bracket into housing. Lift pin end of roller into position and slide
the bracket into the roller pin. Tighten all four bolts.
7. Complete electrical hook-up by snapping motor 1/3 wire connectors into case connectors.
8. Return to motor end and insert safety clip over casting bracket to secure motor end.
CAUTION! DO NOT CUT TAPE ON FABRIC WITH A KNIFE OR ANY SHARP TOOL. REMOVE BY HAND.
9. Carefully remove tape strips securing picture surface around roller. Slat should move freely (Fig. 2). (Only if the
roller assembly is pre installed.)
10. Test installation by operating the screen several times. Be prepared to stop the screen. The door assembly will not
close until the wall switch is placed in the up position and when the screen motor stops at its limit switch in the up
direction.
NOTE: Unit duty cycle is 1 minute on, 3 minutes off.
NOTE: Excessive continuous operation may cause the motor to overheat. If this happens the motor will shut off until it cools to
a normal operating temperature.
11. Close door assembly and replace four bolts at ends of door (2 bolts on each end) (Fig. 1).
SCREEN AND ROLLER ASSEMBLY INSTALLATION
SCREEN MOTOR
FIGURE 2
DUAL MOTOR LVC
CONTROL BOX
SCREEN MOTOR
LIMIT SWITCHES
s
!
DOOR MOTOR
DOOR MOTOR
LIMIT SWITCHES ACCESS DOOR
ASSEMBLY
Produktspecifikationer
| Varumärke: | Da-Lite |
| Kategori: | Projektionsduk |
| Modell: | Large Advantage Deluxe Electrol 36861 |
Behöver du hjälp?
Om du behöver hjälp med Da-Lite Large Advantage Deluxe Electrol 36861 ställ en fråga nedan och andra användare kommer att svara dig
Projektionsduk Da-Lite Manualer
6 Oktober 2024
2 Oktober 2024
29 September 2024
27 September 2024
26 September 2024
25 September 2024
11 September 2024
5 September 2024
2 September 2024
1 September 2024
Projektionsduk Manualer
- Projektionsduk Draper
- Projektionsduk Pyle
- Projektionsduk Vestel
- Projektionsduk Kodak
- Projektionsduk GPX
- Projektionsduk Optoma
- Projektionsduk AV:link
- Projektionsduk Luxburg
- Projektionsduk Elite
- Projektionsduk Projecta
- Projektionsduk Oregon Scientific
- Projektionsduk Duronic
- Projektionsduk Elite Screens
- Projektionsduk EluneVision
- Projektionsduk Celexon
- Projektionsduk Lumene
- Projektionsduk Stewart
- Projektionsduk AWOL Vision
- Projektionsduk Avers
- Projektionsduk Instaal
- Projektionsduk Elite ProAV
- Projektionsduk KHOMO GEAR
- Projektionsduk EPV
Nyaste Projektionsduk Manualer
28 Januari 2025
11 Oktober 2024
29 September 2024
25 September 2024
25 September 2024
23 September 2024
23 September 2024
Celexon Ultramobile Plus Professional 194 x 146 Bruksanvisning
22 September 2024
22 September 2024
22 September 2024