Da-Lite ViewShare Tensioned Advantage Electrol 24055LS Bruksanvisning

Da-Lite Projektionsduk ViewShare Tensioned Advantage Electrol 24055LS

Läs nedan 📖 manual på svenska för Da-Lite ViewShare Tensioned Advantage Electrol 24055LS (12 sidor) i kategorin Projektionsduk. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/12
INSTRUCTION BOOK FOR
ViewShare Tensioned
Advantage Electrol
2
Tools Required for Installation
1. Hang case and attach to support structure with bolts.
See Suggested Methods of Installation.
2. Tighten bolts until trim lange is lush with ceiling.
NOTE: For proper operation, screen assembly must be level
after installation.
3. Remove 2 screws to open junction box. Install electrical
connections that apply to your unit. Make sure to review the
wiring diagram for proper hook up. Replace junction box cover
and secure with 2 screws.
NOTE: Must be installed in accordance with the requirements of
the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
If your case was ordered in advance of the screen and roller
assembly, your installation is now complete. Continue to
step 4 if your Tensioned Advantage Electrol was ordered as a
complete unit.
4. Use supplied 1/8" hex key to remove silver shipping brackets
attached to slat and screen case.
5. Test installation by running screen up and down a few times.
Be prepared to stop screen should any objects obstruct the
movement of the screen. To prevent damage to the motor, the
standard duty cycle is 1 minute on and 3 minutes of.
Case Installation
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
Save These Instructions
Pre-Installation
1. Carefully unpack case from shipping carton.
2. Set aside the Installation Kit. Items inside will be used during
installation.
3. Make sure to recheck measurement of case for proper
installation clearance.
4. Remove any protective foam covering the outside of
the case.
5. For shipping purposes, foam is also inserted between the roller
brackets and endcaps (Figure 1). Remove these foam blocks from
the ends.
6. Remove the hanger brackets from the top of the case using a 1/2”
wrench. Do not discard the hardware; it will be used during case
installation to re-attach the hanger brackets for mounting.
1/2 Open Wrench
or Socket Driver
1/8Hex Key
(included)
3
Suggested Methods of Installation
" Threaded Rod
(Not Supplied)
Hanger Bracket
Electrical
Junction Box
Motor
End
Variable Position
Mounting Bracket
Audience Side
6 ⁄"
6 ⁄"
7 ¾"
" Threaded Rod
(Not Included)
Attached To
Mounting Bracket
Self-Trimming
Flange Finished
Ceiling
7 ¾"
7 ¾"
8"
6 ⁄"
6 ⅜"
3⁄"
7 ⁄"
6 ⁄"
Method 1
Method 2

Produktspecifikationer

Varumärke: Da-Lite
Kategori: Projektionsduk
Modell: ViewShare Tensioned Advantage Electrol 24055LS

Behöver du hjälp?

Om du behöver hjälp med Da-Lite ViewShare Tensioned Advantage Electrol 24055LS ställ en fråga nedan och andra användare kommer att svara dig




Projektionsduk Da-Lite Manualer

Projektionsduk Manualer

Nyaste Projektionsduk Manualer