Datalogic 94A151115 Bruksanvisning

Datalogic Laddare för mobil enhet 94A151115

Läs nedan 📖 manual på svenska för Datalogic 94A151115 (2 sidor) i kategorin Laddare för mobil enhet. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
Datalogic Kyman™ Ethernet Multi Cradle
The Datalogic Kyman™ Ethernet Multi Cradle provides power for
charging up to four mobile computers simultaneously and also connects
up to four mobile computers to an Ethernet network.
Figure 1 – Datalogic Kyman™ Ethernet Multi Cradle General View
Key:
A) Link LED for Ethernet Port 1
B) Speed LED for Ethernet Port 1
C) Datalogic Kyman™ Charging Status LED
D) Power supply connector
E) Ethernet Port 1 (with integrated Link and Speed LEDs)
F) Ethernet Port 2 (with integrated Link and Speed LEDs)
822000790
The Ethernet cradle drivers are pre-installed on the Datalogic Kyman™
and initiate automatically when the Datalogic Kyman™ is placed in a
properly connected Four Slot Ethernet cradle.
When the mobile computer is inserted into the Four Slot Ethernet cradle,
the LAN icon indicates that the mobile computer is connected to a
network.
The green Speed LED lights to indicate that the transfer rate is 100 Mbps.
When it is not lit it indicates that the transfer rate is 10Mbps.
NOTE
The maximum bandwidth capacity for each Mobile
Computer is 12Mbps.
The yellow Link LED blinks to indicate activity, or stays lit to indicate that
a link is established. When it is not lit it indicates that there is no link.
The Speed LED and the Link LED integrated in Ethernet Port 1 and 2
function in the same way.
The Charging Status LED on the mobile computer shows the status of the
battery charging. The maximum time required to recharge a completely
run-down battery pack is about 3 hours for Li-Ion batteries. See Datalogic
Kyman™ User’s Manual for Charging Status LED indications.
Correct Mobile Computer Insertion / Removal
Insert the mobile computer into a slot to begin charging and start
communication.
For correct insertion onto the cradle, insert the mobile computer from the
top of the cradle and push it down firmly.
Figure 2 - Mobile Computer Insertion
To remove the mobile computer from the Datalogic Kyman™ Ethernet
Multi Cradle, simply pull it upwards while holding the cradle firmly down.
TECHNICAL FEATURES
Electrical Features
Power supply from 12 to 14 VDC ± 5%
Consumption Max 7 A
Indicators Ethernet Link LED (yellow)
Ethernet Speed LED (green)
Charge time (when PDA is off) max 3 hours (Li ION batteries)
Communication Features
Interface Ethernet 10/100 Base T
Environmental Features
Working temperature 0° to +50°C / 32° to 140°F *
Storage temperature -20° to +70°C / -4° to 158°F
Humidity 90% non condensing
Degree of protection IP20
Mechanical Features
Dimensions 480 x 137 x 190 mm
18.89 x 5.4 x 7.48 in
Weight about 2940 g / 104 oz
* Batteries must be charged at a temperature ranging from 0° to 45 °C
(+32° to 113°F).
F
E
D
B
A
C
CONNECTIONS
CAUTION
Connections should always be made with power OFF!
Ethernet Connection
Connect the Ethernet cradle (Ethernet port 1) to an Ethernet hub or a port on
the host device. Connect the Ethernet cradle (power port) to power supply.
Figure 3 - Ethernet Connection
Key:
A) Datalogic Kyman™ Ethernet Multi Cradle
B) 94ACC1337 FPS19 W/O Power Cord
94ACC1150 Power cord EU 3-pin
C) UTP CAT 5E cable (recommended use)
D) Ethernet hub
Daisychaining Ethernet Connection
To connect several cradles to an Ethernet network, Ethernet cradles may be
daisychained. It is recommended not to connect more than 4 cradles in order
to maintain the optimal baud rate. The Speed LED and the Link LED on the
Ethernet Port 2 function in the same way as the Speed LED and the Link LED
on the front of the cradle.
To daisychain cradles:
1. Connect the first Ethernet cradle to power and to the Ethernet Switch as
shown on Figure 4.
2. Connect power to the second Ethernet cradle.
3. Connect the daisychain Ethernet cable (either straight or twisted cable
can be used) between Ethernet Port 2 of the first cradle, and Ethernet
Port 1 of the second cradle.
4. Connect additional cradles as shown in Figure 4.
Figure 4 - Daisychaining Ethernet Connection
Key:
A) Ethernet hub
B) Ethernet Port 1
C) Ethernet Port 2
D) 94ACC1337 FPS19 W/O Power Cord
94ACC1150 Power cord EU 3-pin
E) UTP CAT 5E cable (recommended use).
Power Supply
Each Ethernet Multi Cradle requires a power supply to be connected to
the cradle. We recommend the DL FPS19 power supply.
Figure 5 - Power Supply Polarity
COMPLIANCE
WEEE Compliance
DATALOGIC MOBILE S.r.l.
Via S. Vitalino, 13
40012 - Lippo di Calderara
Bologna - Italy 06
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
KYMAN Ethernet Desk Multi Cradle
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi
and further amendments
et ses successifs amendements
und späteren Abänderungen
y succesivas enmiendas
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla
sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product
safety.
Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité
des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit
und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad
electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:
EN 55022 (C LASS A ITE), AUGUST 1994:
AMENDMENT A1 (CLASS A ITE), OCTOBER 2000:
LIMITS AND METHODS OF MEASUREMENTS OF RADIO
DISTURBANCE OF INFORMATION TECHNOLOGY EQUIPMENT
EN 55024, S EPTEMBER 1998: INFORMATION TECHNOLOGY EQUIPMENT. IMMUNITY
CHARACTERISTICS
. LIMITS AND METHODS OF
MEASUREMENTS
Lippo di Calderara, May 19th, 2007
Paola Chientaroli
Quality Assurance Manager
D
A
B
C
D
C B
A
E

Produktspecifikationer

Varumärke: Datalogic
Kategori: Laddare för mobil enhet
Modell: 94A151115

Behöver du hjälp?

Om du behöver hjälp med Datalogic 94A151115 ställ en fråga nedan och andra användare kommer att svara dig


Laddare för mobil enhet Datalogic Manualer

Datalogic

Datalogic 94A151115 Bruksanvisning

17 Augusti 2024
Datalogic

Datalogic 94A151132 Bruksanvisning

25 Juli 2024

Laddare för mobil enhet Manualer

Nyaste Laddare för mobil enhet Manualer

Tripp Lite

Tripp Lite CSC32USBW Bruksanvisning

20 Oktober 2024
Anker

Anker PowerCore+ 20100 USB-C Bruksanvisning

16 Oktober 2024
Bauhn

Bauhn ACRWC-0424-M Bruksanvisning

15 Oktober 2024
Bauhn

Bauhn AFTC3-0424-W Bruksanvisning

15 Oktober 2024
Bauhn

Bauhn AFTC3-0424-B Bruksanvisning

15 Oktober 2024
Bauhn

Bauhn ACRWC-0424-W Bruksanvisning

15 Oktober 2024
Bauhn

Bauhn ADMWC-0224 Bruksanvisning

15 Oktober 2024
Black Box

Black Box Deluxe UCCSM-10-30TP-HASP Bruksanvisning

14 Oktober 2024
Trust

Trust 90W Notebook Power Adapter Bruksanvisning

11 Oktober 2024
Black Box

Black Box Deluxe UCCSL-12-36HP Bruksanvisning

10 Oktober 2024