Davis DAV-7747 Bruksanvisning

Davis Inte kategoriserad DAV-7747

Läs nedan 📖 manual på svenska för Davis DAV-7747 (16 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/16

Daytime Fan-Aspirated Radiation

Shield Kit Installation Manual

For Vantage Pro2™ & Vantage Pro2 Plus™ Stations

Introduction

The instructions describe how to upgrade a non-aspirated Vantage Pro2 radia-

tion shield to a Daytime Fan-Aspirated Radiation Shield.

The upgrade kit can be installed on any Vantage Pro2 or Vantage Pro2 Plus

Integrated Sensor Suite (ISS) equipped with a non-aspirated radiation shield.

Components

The upgrade kit includes the following components:

Closed Cap Plate

Open Cap Plate

Open Plate

SIM Cover

Fan Plate

Daytime Fan Kit Components

Davis Instruments, 3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A. • 510-732-9229 • www.davisnet.com

Installing the Daytime Fan Kit

The kit also includes the following hardware:

Tools Needed

You may need some or all of the following tools to complete the upgrade:

• A medium Phillips-Head screwdriver

• A medium slot-tip screwdriver

• Other tools as required to remove and re-mount the ISS

Installing the Daytime Fan Kit

Installation Overview

These are the steps to install the Daytime Fan components:

1. — Put the console into Setup Mode.For Consoles Only

2. Take the ISS down from its installed position.

3. Disassemble the standard radiation shield.

4. Check Temperature/Humidity sensor orientation.

5. Assemble the lower section of the fan-aspirated shield.

6. Install the fan unit.

7. Assemble the upper section of the fan-aspirated shield.

8. Re-Install the ISS.

9. Take the console out of Setup Mode.

For Consoles Only— Put Console in Setup Mode

If you have a console, you need to put it in Setup Mode. This prevents the

reception of erroneous data while you are removing the ISS.

If you have an Envoy and are concerned with erroneous data, you may edit the

data via the WeatherLink software. See the WeatherLink Online Help for more

information.

#8-32 x 3-1/4" Screws

(3)

#8-32 x 1/2" Screws

(3) Threaded Spacers

(3)

#8 Split-Lock Washers (6)

#8 Flat Washers (6)

12" Cable Ties (2)

Daytime Fan Kit Hardware

Installing the Daytime Fan Kit

To put your console in Setup Mode:

At your Vantage Pro2 console, press and hold DONE and then press the

down arrow (-) to put the console in Setup Mode. This prevents the

reception of erroneous data while you are removing the ISS.

Note: If the console acquires erroneous data during the upgrade, see Take the Console Out

of Setup Mode on page 16 for instructions on clearing data. Additional information on

clearing console data can be found in the .Vantage Pro2 Console Manual

Take Down the ISS

Please work on your Vantage Pro2 ISS in a safe place. If you are installing the

Daytime Fan Kit on an ISS that has already been placed into service, you will

need to take down the ISS from its sited location and move it to a convenient

and safe place to perform the installation.

To disassemble the ISS:

1. Locate the Sensor Interface

Module (SIM) housing cover

on the side of ISS and open it.

2. Disconnect the Solar Panel

wire on the SIM cover from

the SIM board by pulling the

Solar Panel connector.

3. Pull the foam insert out of the

cable access port in between

the cables and set the foam

insert aside.

4. Disconnect the anemometer

cable from the sensor

connector labeled WIND and,

if you are using a cabled

model, disconnect the console

cable from the SIM and slide

the cables out of the cable

access port.

5. You can now remove the ISS from its mounted position. Move it to a safe

place to install the kit components.

Disassemble the Standard Radiation Shield

Note: We recommend using a workbench or table to perform the following procedures.

1. Open and remove the SIM cover if you have not done so already.

2. Disconnect the Temperature/Humidity cable from the SIM and slide the

cable out of the cable access port.

Lift off cover,

unplug solar power

connector

Detaching the SIM Cover

Produktspecifikationer

Varumärke:	Davis
Kategori:	Inte kategoriserad
Modell:	DAV-7747

Behöver du hjälp?

Om du behöver hjälp med Davis DAV-7747 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Davis Manualer

Davis DAV-7720 Bruksanvisning

26 Oktober 2024

Davis DAV-7716 Bruksanvisning

26 Oktober 2024

Davis DAV-7714 Bruksanvisning

26 Oktober 2024

Davis DAV-6351 Bruksanvisning

26 Oktober 2024

Davis DAV-7654 Bruksanvisning

26 Oktober 2024

Davis DAV-6316 Bruksanvisning

26 Oktober 2024

Davis DAV-6420 Bruksanvisning

25 September 2024

Davis DAV-6410 Bruksanvisning

25 September 2024

Davis DAV-7747 Bruksanvisning

13 September 2024

Davis WeatherLink Bruksanvisning

13 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024