Draper 218089 Bruksanvisning
Draper
Projektionsduk
218089
Läs nedan 📖 manual på svenska för Draper 218089 (2 sidor) i kategorin Projektionsduk. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/2
Assembly Instructions
Cinefold Portable Projection Screen by Draper
Frame Hinges and
hinge locks
Handy
Crank
Viewing
Surface
KE
Adjustment
Knob
2" Min.
44" Max.
Anti-sway stabilizers
optional with HD legs
Standard
T-Leg
Frame
Snaps
Handy Crank Viewing
Surface
Bottom row of snap
studs to accept skirt
Standard T-Leg
Heavy duty legs optional
Frame/Screen Assembly
① Open carrying case and remove pouch containing screen surface, and
three aluminum assemblies. The largest package is the frame. Unwrap and
unfold it completely in one direction only, locking all hinges. Frame should
lie with snaps facing up.
② Remove surface from its envelope. With male snaps at bottom, snap
surface to frame. For easier surface attachment, start in one corner, then
work your way around the frame. Make sure snaps are secure.
Please note: For steps 3-5, screen should remain on fl oor or table, with
surface facing up. Carefully lift screen from fl oor or table to complete each
step.
③ Lock corner braces.
④ Unfold leg assemblies and lock hinges. Check that ad just ment knob is in
the hole desired (upper for vertical screen position, lower for keystone
elimination). DO NOT unfold feet at this time.
⑤ Attach legs to back side of vertical frame sections, as indicated by the
color coded markings, using Handy Cranks. For standard screen height,
match colored tapes exactly. Height is adjustable in 6" increments.
⑥ Raise Cinefold to a vertical position and unfold feet. Tighten ad just ment
knobs to maintain legs at desired angle. If your screen includes Heavy-
Duty Legs, unfold and lock the extensions on the backs of the feet, hinge
up to the backs of the leg, and attach with Handy Crank.
⑦ If Anti-Sway stabilizers are supplied with your screen, refer to illustration
and attach with Handy Cranks.
A Note About Surfaces
① Always fold with snaps face-to-face. Do not permit screen fabric to
contact border material or snaps when folded. Store in pouch
provided.
② Take care at all times not to permit Cinefold viewing surface to contact any
dusty or dirty area, nor any varnished or painted object.
③ When necessary, clean Cinefold viewing surface with soap and water. mild
USE NO SOLVENTS! Surface must be completely dry before folding.
Caution
① Read instructions through completely before proceeding; retain for future
reference.
② Handle viewing surface with care; do not allow it to come in contact with
sharp or dirty objects.
③ Use Handy Cranks provided; failure to do so may lead to screen damage.
④ Make sure screen is level.
⑤ Do not write on viewing surface.
⑥ The ideal temperature range for assembling folding screens to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
Copyright © 2011 Draper Inc. Form Cinefold_Inst11 Printed in U.S.A.
®
Caution: Beware
of pinch points.
Caution: Make sure all hinges and joints are locked
before raising screen to standing position.
Caution: Make sure screen
is placed on level surface.
Assembly Instructions
Truss-Style Cinefold Portable Projection Screen by Draper
Truss Assembly
① Remove pouch containing viewing surface from case and set aside.
Remove all aluminum assemblies.
② Unfold all folded aluminum assemblies completely, noting labels and
color-coded marks. Lock all hinges. Position Stage Right and Stage Left
sections in appropriate positions with snaps facing . Top and Bottom up
sections should be set with snaps facing .down
③ To increase frame rigidity, hinges on top and bottom frame sections have
rivnuts marked with red and green. Insert a Handy Crank through the
threadless rivnut (red) and tighten into the threaded rivnut (green).
④ Apply small sections marked “Stiffener Bars” to back of Bottom frame
section, using eight Handy Cranks each. Failure to use all Handy Cranks
may result in damage to screen frame. Turn Bottom frame section over so
snaps face up.
⑤ If your screen frame is less than 25' wide, repeat step 4 for Top frame sec-
tion. Frames 25' wide and over are equipped with a special full-width Stiff-
ener for the top frame section. To attach it, place Stiffener fl at with green
rivnuts face down. Place top frame section on top of and at right angles
to Stiffener, over the green rivnuts. Insert and tighten standard Handy
Cranks. Install 45° angle braces to the Top frame section and Stiffener with
short Handy Cranks. Turn Top frame so snaps face up.
Dress-Up Kit Assembly
PLEASE NOTE: All components are labeled and color coded to
facilitate assembly.
A. Valance Bar attaches to frame with simple bayonet-style mounting.
B. Draper Bars mount to Valance Bar, bayonet-style.
C. Optional adjustable Skirt Bar is secured to frame at desired level with
positive-locking plunger mechanism. If Skirt Bar is not used, Skirt may
be snapped to bottom of viewing surface.
D. Valance, Drapes, and Skirt snap onto Mounting Bars.
E. Gaps between the frame and the valance can be easily removed by
pulling the bottom edge of the valance to close the gap.
F. Pulling and smoothing the edges of the panels will remove any
wrinkles or puckers that might be present when product is unfolded.
Drapery
Bar
Valance Bar
Drapery
Bar
Adjustable Skirt Bar
Rigid
Truss
Frame
Anti-Sway
Stabilizers
Heavy-Duty
Legs
Frame & Legs
Assemble with
Handy Cranks
Handy Crank
⑥ Join Top and Bottom to Stage Right and Stage Left, using two Handy
Cranks on each of the four corners. Match numbers on white labels, and
keep in mind that no Handy Crank should protrude outside screen frame.
⑦ Remove surface from pouch. With the row of male snaps at bottom, posi-
tion screen surface over frame. Snap each of the four corners, then snap
across bottom, up sides, and across top.
⑧ Attach feet to inner side of legs with Handy Cranks, matching color-coded
markings. Attach legs to Stage Right and Stage Left with Handy Cranks,
matching colored tapes.
⑨ Raise screen to a vertical position. Add Heavy-Duty Legs and Anti-Sway
Stabilizers with Handy Cranks in the positions indicated below.
Copyright © 2010 Draper Inc. Form Cinefold_Inst11 Printed in U.S.A.
®
Caution: Make sure all hinges and joints are locked
before raising screen to standing position.
Caution:
Make sure
screen is placed
on level surface.
Caution: Beware
of pinch points.
Caution
① Read instructions through completely before proceeding; retain for future
reference.
② Handle viewing surface with care; do not allow it to come in contact with
sharp or dirty objects.
③ Use Handy Cranks provided; failure to do so may lead to screen damage.
④ Make sure screen is level.
⑤ Do not write on viewing surface.
⑥ The ideal temperature range for assembling folding screens to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
A Note About Surfaces
① Always fold with snaps face-to-face. Do not permit screen fabric to
contact border material or snaps when folded. Store in pouch
provided.
② Take care at all times not to permit Cinefold viewing surface to contact any
dusty or dirty area, nor any varnished or painted object.
③ When necessary, clean Cinefold viewing surface with soap and water. mild
USE NO SOLVENTS! Surface must be completely dry before folding.
Produktspecifikationer
| Varumärke: | Draper |
| Kategori: | Projektionsduk |
| Modell: | 218089 |
Behöver du hjälp?
Om du behöver hjälp med Draper 218089 ställ en fråga nedan och andra användare kommer att svara dig
Projektionsduk Draper Manualer
22 September 2024
21 Augusti 2024
17 Augusti 2024
17 Augusti 2024
15 Augusti 2024
12 Augusti 2024
9 Augusti 2024
8 Augusti 2024
8 Augusti 2024
7 Augusti 2024
Projektionsduk Manualer
- Projektionsduk Pyle
- Projektionsduk Optoma
- Projektionsduk Da-Lite
- Projektionsduk AV:link
- Projektionsduk Projecta
- Projektionsduk Duronic
- Projektionsduk Celexon
- Projektionsduk Lumene
- Projektionsduk Stewart
- Projektionsduk Avers
- Projektionsduk Instaal
- Projektionsduk Elite ProAV
- Projektionsduk KHOMO GEAR
- Projektionsduk EPV
Nyaste Projektionsduk Manualer
11 Oktober 2024
6 Oktober 2024
2 Oktober 2024
29 September 2024
29 September 2024
27 September 2024
26 September 2024
25 September 2024
25 September 2024
25 September 2024