Drayton Erie Digistat 2 Bruksanvisning

Drayton Erie Termostat Digistat 2

Läs nedan 📖 manual på svenska för Drayton Erie Digistat 2 (2 sidor) i kategorin Termostat. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

8. Press the “SET?” button, this tells you

that at 8.30 a.m., the heating system

will control your home at 16°C. If you

wish to alter this temperature use the

+ and – buttons.

9. Continue to press the “SET?” button

as in steps 6 and 7 above to advance

through the times and temperatures.

If you wish to alter any of the times

and temperatures use the + and

– button, when the one you wish to alter is flashing.

10. Continue to press “SET?” button until

you return to normal operating mode

with a display similar to the one shown

here.

OPERATING MODES

The Digistat can be operated in one of three modes.

1) – Timed, all preset times and temperatures

2) – Continuous night temperature (useful for low limit

temperature protection when on holiday)

3) – Continuous ‘DAY 1’ temperature

Use the SELECT button to change the operating mode to suit

your requirements, the symbols are positioned on the right

hand side of the display.

TEMPERATURE OVERRIDE

If at anytime during normal operation you wish to temporarily

increase or decrease the set temperature, use the + or –

buttons to change to your desired setting. This can be done

without entering the SET mode. Five seconds after releasing the

+ or – button the display will revert to showing the actual

room temperature. The Digistat will now control the

temperature to the override setting until the next programmed

switching time, when it will revert to the times and

temperatures you have already programmed.

Continued overleaf.

4. Press “SET?” button twice to return

to normal operating mode.

PRE-PROGRAMMED TIMES AND

TEMPERATURES

The Digistat 2 comes with the following preset programme.

Symbol Setting Time Temperature

1st day time 6.30 am 20°C

2nd day time 8.30 am 16°C

3rd day time 4.30 pm 21°C

Night time 10.30 pm 7°C*

* 16°C if selector pin removed, see installation instructions

TO VIEW OR CHANGE THE FACTORY

SETTINGS (steps 5-10)

5. Press the “SET?” button until this

display is shown.

6. Press the Yes (–) button again. This

tells you that at 6.30 a.m., the heating

system will control your home at

20°C. If you wish to alter the

temperature use the + and – buttons.

7. Press the “SET?” button. The time

will now flash. If you wish to alter the

switching time use the + and

– buttons. This will change the

switching time in 10 minute steps.

Digistat 2 user instructions

INITIAL START UP

Open the battery compartment situated at the bottom left

hand corner (press to unlatch and slide down). Remove the

insulator strip from between the batteries and their contacts

and close the compartment.

The unit will now display the actual

room temperature and time at 12.00 am,

midnight (Diagram A).

If the unit has been stored in a cold

place, it may take time to warm up.

Digistat 2 has an indicator to show

when the heating system is ON or OFF,

e.g. if the SET temperature is 20°C and

the actual room temperature is below

20°C a flame symbol will appear on the

display (Diagram B). This indicates a de-

mand for heat (system will switch ON).

During normal operation, the Digistat 2 will display actual

room temperature continuously.

SETTING THE TIME OF DAY (steps 1-4)

The diagram next to each step description shows resulting display.

1. Press “SET?” button

2. Press “Yes” (–) button. The hours

will flash as shown here. Use the +

and – buttons to set correct hour.

3. Press “SET?” button again and the

minutes will flash, use + and –

buttons to set correct minute time.

SYSTEM OFF

SYSTEM ON

Diagram A

Diagram B

BATTERY REPLACEMENT

30 days before the batteries need

replacing, a battery symbol will flash in

the right hand side of the display,

(Diagram C). This signifies that two

1.5V type AA alkaline batteries

will be needed to replace the existing

ones. If battery replacement is carried out in this condition

the programmed settings will only be held in the memory for

a maximum of one minute, after which re-programming may

be necessary.

IMPORTANT

To avoid the possibility of having to

re-programme the switching times

and temperatures, it is advisable to

wait until the display with a flashing

battery symbol changes to a

continuous battery only display

(after 30 days – Diagram D). In this condition the unit will

remain OFF but your programmed settings will be held in

memory for a number of weeks. The battery compartment

can now be left open, to replace the batteries, for

approximately one hour. If the compartment is left open for

longer, the unit will revert to the factory preset times and

temperatures. It may be necessary to reset the correct time

of day after changing the batteries.

The battery compartment is situated at the bottom of the

unit (press to unlatch and slide down). Ensure new batteries

are installed correctly.

HELPFUL HINTS

1) First/last set times

The Day 1 setting cannot be programmed before

12.00am. The night setting can be programmed at

whatever time you require, even after 12.00 am (midnight) so

long as it is not programmed more than 23 hours 50 minutes

after the Day 1 setting.

2) Part or full day omission

If during programming the Digistat, one of the symbols on the

left hand side of the screen starts to flash, this indicates that

two or more of the switching times have been set to the

same time. This facility enables you to omit one or more of the

switched periods. When one or more switching times are

programmed together the later setting takes precedent. For

example, if all four switching times were set together the

Digistat would control continuously at the fourth (night)

temperature setting .

3) Programme sequence

The Digistat will not allow you to program the switched

periods out of sequence but will hold the times together as

stated above.

4) Reset

If at any time during the programming you get confused and

would like to start the procedure from the beginning press the

SELECT and – buttons at the same time and hold for two

seconds. This resets the Digistat to the factory pre-set times

and temperatures shown in the table (overleaf).

5) Self revert

If during programming no button is pressed for between one

and two minutes the Digistat will revert automatically to its

normal operating mode.

Diagram D

Digistat 2

User instructions

Diagram C

CONFORMS TO THE ESSENTIAL

REQUIREMENTS OF THE FOLLOWING

DIRECTIVES:

89/336/EEC – Electromagnetic compatibility

73/23/EEC – Low voltage directive

Drayton

Siebe Climate Controls Limited

Chantry Close, West Drayton, Middlesex UB7 7SP

Telephone: (01895) 444012 Sales Fax: (01895) 421901

Technical Helpline Telephone: (01895) 460444

A Siebe Group Product

Siebe Climate Controls reserve the right to make changes without notice and 090 678

cannot accept liability for errors. 0898

Produktspecifikationer

Varumärke:	Drayton Erie
Kategori:	Termostat
Modell:	Digistat 2

Behöver du hjälp?

Om du behöver hjälp med Drayton Erie Digistat 2 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Termostat Drayton Erie Manualer

Drayton Erie Digistat 3 Bruksanvisning

14 September 2024

Drayton Erie Digistat 2 Bruksanvisning

12 September 2024

Termostat Manualer

Nyaste Termostat Manualer

Danfoss ORT-10 Bruksanvisning

27 Oktober 2024

Hunter 44279 Bruksanvisning

27 Oktober 2024

Heatmiser PRT-ETS Bruksanvisning

26 Oktober 2024

Heatmiser PRT-W Bruksanvisning

26 Oktober 2024

Heatmiser PRTHW Bruksanvisning

26 Oktober 2024

Heatmiser PRT-EWTS Bruksanvisning

26 Oktober 2024

Heatmiser DT-N Bruksanvisning

26 Oktober 2024

Heatmiser DT-EW Bruksanvisning

26 Oktober 2024

Heatmiser PRTHW-WTS Bruksanvisning

26 Oktober 2024

Heatmiser PRT-RPTS Bruksanvisning

26 Oktober 2024