EAT E-Glo Bruksanvisning

EAT Inte kategoriserad E-Glo

Läs nedan 📖 manual på svenska för EAT E-Glo (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/6
EAT E-Glo
Phono Preamplifier
Owner´s Guide
Thank You for choosing EAT. Please take a few moments to review this manual so you may
enjoy all the benefits of your new E-Glo phono preamplifier.
IMPORTANT SAFETY INSTRUCTIONS
- Read all the safety and operating instructions before operating this product. Retain safety
and operating instructions for future reference.
- Operate this product only from the type of power source indicated on the label on back
panel of EAT Power Supply unit. Use of any other voltage will likely damage the unit and void
the warranty.
- Avoid letting liquids enter the device or the power supply. Never place any item containing
liquid, such as a flower vase on or near the device. Never spill any liquid on the device or the
power supply. Never place any naked flame sources, such as lighted candles on or near the
device. The product shall not be used in damp or wet locations, next to a bathtub, sink,
swimming pool or any other similar conditions.
- The product should be situated away from heat sources such as radiators, heat registers,
stoves and other products that produce heat.
- Do not attempt to repair or service this product yourself. Opening or removing covers may
expose you to dangerous voltage and other hazard. Refer all servicing to qualified service
personnel.
- Never push objects of any kind into this product through any openings. They may touch
dangerous voltage points or short out parts that could result in fire or electric shock.
- Do not block ventilation slots or heatsinks.
- Unplug this product during lightning storms or when unused for long periods of time.
- Always disconnect your entire system from the AC mains before conecting or disconnecting
any cables or when cleaning any component.
Unpacking
The EAT E-Glo phono preamplifier should be removed from its box with care.We suggest that you
keep all of the original packaging, storing it in a safe, dry place in the event that you´re required to
transport this product.
EAT Power Supply unit
Power cables
Connect the grey power cable from the EAT Power Supply unit to the POWER socket of the EAT E-Glo
phono preamplifier and then connect the unit to the mains (mains power cable is not suplied).
Prior to turning this preamplifier on, make sure that every cable on both units is properly connected
to avoid any problems.
Main Power switch is located on the rear panel of the Power Supply unit.
The state of the unit is indicated by the LED´s on the front panel.
Power : the green LED illuminate, indicating that the unit is in stand by.
Anodes: the green LED illuminate, indicating that the EAT phono preamplifier is powered up and
ready to play.
On sequence: the unit heats up for 40seconds after the main power switch is turned ON.
Fuse replacement : For the 230V version use a T1A L / 250V (5x20mm size).

Produktspecifikationer

Varumärke: EAT
Kategori: Inte kategoriserad
Modell: E-Glo

Behöver du hjälp?

Om du behöver hjälp med EAT E-Glo ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad EAT Manualer

EAT

EAT E-Glo Bruksanvisning

23 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024