Elektrobock PT52 Bruksanvisning

Elektrobock Termostat PT52

Läs nedan 📖 manual på svenska för Elektrobock PT52 (14 sidor) i kategorin Termostat. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/14

MADE IN CZECH REPUBLIC

• LARGE BACKLIT DISPLAY

with intuitive navigation in English

• 9 WEEKLY PROGRAMS FOR

CENTRAL HEATING (C.H.)

6 temperature changes per day

• OPERATION OPTIMIZATION

preliminary switch-on function

• CONTROL TYPE SELECTION

according to room or equitherm control

• 1 WEEKLY PROGRAM FOR

HOT SERVICE WATER (D.H.W.)

3 temperature changes per day

• UP TO 30 % ENERGY SAVINGS

quick investment return

DESCRIPTION

PT52 is intended for controlling gas and electric boilers which use the OpenTherm Plus (OT+) communi-

cation protocol. Its great advantages are the backlit display and navigation in CZ/PL/EN/DE/RU.

INSTALLATION AND LOCATION

Install the thermostat at a suitable place where its operation will not be affected by direct ﬂ ow of hot air

from a heating source, by sunshine or other disturbing effects. Do not install it on an external wall either.

The installation height should be at least 1.5 m above the ground. Locate the thermostat in the so-called

reference room, such as the living room (the heat source will be switched according to the temperature

in this room).

The installation can only be done by a person with adequate qualiﬁ cation! Before

installation, disconnect the power supply!

1) Remove the control part from the bottom cover of the device (Fig. 1, page 3).

2) Chip off the plastic piece in the middle of the bottom cover to lead in the conductors.

3) Run the conductors through the hole and connect them to the terminal board acc. to the diagram.

4) Fasten the bottom cover to the wiring box by means of screws (Fig. 2, page 3).

5) Mount the control part onto the bottom cover.

6) Upon the ﬁ rst start (or reset), the thermostat shows the “SET TIME” message; set the current

time and date acc. to the instructions on page 5.

7) To change the navigation menu language, follow page 8 (Czech set by default).

8) Ask the boiler manufacturer, whether it communicates by means of the standard OpenTherm Plus

protocol (for the Thermona, Ferolli and Viessmann boilers, change the constant No. 26, see page 13).

Wiring diagram:

Backlit display

After you press any button, the display is backlit automatically for at

least 5 s (activated within 30 min after connecting the OT line).

Controls

turning = change of temperature setting

short press = selection (entry) conﬁ rmation

= quick change of required

temperature or program (see page 3);

viewing other information (see page 4)

long press = step back (only in the CONST mode,

page 8)

press = opening the main menu or returning

a step back

PT52 BOILER

OpenTherm communication line,

max. length of 50 m, no polarity

The OpenTherm

communication terminals

are marked differently

with every boiler type;

therefore, observe the

electric connection

recommended by the

boiler manufacturer!

TEMP. IN AUTO

TEMP. IN MANU

8 9

11 13 14

Fig.1

USER TIPS

Fig.2

QUICK CHANGE OF REQUIRED TEMPERATURE / PROGRAM

Press twice the“ “ button; the required temperature starts ﬂ a-

shing on the display. Change the required temperature by turning

the “ “ pbutton for further informati- “ button and press the “

on, or “ “ to return to the main menu.

In the AUTO mode, the change will last until the next program

change. In this mode, another program can be selected in the

same way.

In the MANU mode, the change is permanent.

By successively pressing the “ “ button, you can view further informa-

tion on the: required temperature of hot service water, external tempera-

ture, central heating temperature, boiler output, and operating hours of

the central heating and hot service water; for detailed description, see

page 4.

1, Current day (in the

Prog mode, selection

of days to be

programmed)

2, Heating on indication

3, Hot service water

indicator

4, Central heating

indicator

5, Current room

temperature

6, Anti-freeze temperature

7, Modes for setting

programs (PROG) and

constants (CONST)

(page 6 and 8)

8, Automatic mode

(page 5)

9, Manual mode (page 5)

10, Holiday mode (page 5)

11, Clock setting mode

12, Permanent shut-off

(page 5)

13, Summer mode

14, Boiler inspection indic.

15, OpenTherm (OT+)

communication indic.

16, Current time

17, Current date/

required temperature/

modulation output in %

(in the CONST mode,

for example, number

of the equitherm curve;

for details, see page 9 )

18, Status line, dynamically

changing according to

the running process

19, Key lock indication

Produktspecifikationer

Varumärke:	Elektrobock
Kategori:	Termostat
Modell:	PT52
Färg på produkten:	Beige, Red
Snäll:	Modelspoorbaan/trein
Rekommenderad ålder (min):	14 jaar
Antal per paket:	4 stuk(s)
Längd:	1117 mm
Föreslaget kön:	Jongen/meisje
Antal bitar:	4 stuk(s)
Typ produkt:	Treinmodel
Ljud:	Ja
Ej för barn 0-3 år:	Ja
Lättnad:	Ja