Elite Screens ZSP-TR01 Bruksanvisning

Elite Screens Kontroller ZSP-TR01

Läs nedan 📖 manual på svenska för Elite Screens ZSP-TR01 (3 sidor) i kategorin Kontroller. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/3
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
Wireless RF Projector Trigger Controller
Part# ZSP-TR01
User Guide
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
SPECIFICATIONS
1. Size and Weight: W x H x D: 4.8”x2”x0.7”, Weight: 0.09LBS
2. : 80 feet (25M) Max. Control Distance
Control Type: ASK / FSK
3. 15V Projector Output Support Trigger Voltage: 3－
4. 315Mhz, Power Below 2 milli-watts RF Spec. Frequency: ：
5. : Directions for user
a. Connect the wireless RF trigger controller and the projector as shown below.
b. Use the wireless RF trigger controller to synchronize the screen drop/rise with the
projection s power cycle via remote control according to the version number on ’
your screen. Version number can be located either on the screen’s end cap
sticker or on the outside sticker of the packaging box.
Location of version number
on end cap sticker.
Fig. 1
Location of version number
on packaging box sticker.
Fig. 2
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
Note: Directions for synchronizing your 5-12V wireless trigger according to the
version number.
Version 1.4 (5-12V wireless trigger and Elite electric screen must be the same version)
Step 1: Push the small button located on the circuit board on the left side of the projection screen
(please note: you may require a small sharp object to achieve this After the light turns on, ). LED
press & hold the button on your Wireless RF Trigger Controller and make sure the LED light on UP
circuit board turns on.
Step 2: Continue to hold the button for an additional 3-4 seconds. After 3-4seconds, your 5- V up 12
Wireless Trigg should er be activated and you’ll be able to control your screen with your projector s ’
power cycle .
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around
20-30 seconds for full off and on cycle each time)
Version 2.0 (5-12V wireless trigger and Elite electric screen must be the same version)
Step 1: Make sure to unplug your screen from the power outlet
Step 2: Hold the UP button on your 5-12V wireless trigger
Step 3: While holding the button, plug the screen back to the power outlet UP
Step 4: Wait 5 seconds and then release the button UP
Step 5: Your 5-12V wireless trigger should now be activated with your screen and ready to be used
and able to control your screen with your projector s power cycle. ’
Repeat the steps again if not successful.
Note: Once your RF remote has been activated, th synchronization will be saved even the power e if
is cut off.
Fig. 3

Produktspecifikationer

Varumärke: Elite Screens
Kategori: Kontroller
Modell: ZSP-TR01

Behöver du hjälp?

Om du behöver hjälp med Elite Screens ZSP-TR01 ställ en fråga nedan och andra användare kommer att svara dig


Kontroller Elite Screens Manualer

Elite Screens

Elite Screens ZSP-TR01 Bruksanvisning

11 September 2024

Kontroller Manualer

Nyaste Kontroller Manualer

8BitDo

8BitDo Ultimate C Wired Controller Xbox Bruksanvisning

26 Oktober 2024
DJI

DJI Motion Controller Bruksanvisning

18 Oktober 2024
PCE Instruments

PCE Instruments PCE-RE100P Bruksanvisning

16 Oktober 2024
PCE Instruments

PCE Instruments PCE-RE21R Bruksanvisning

16 Oktober 2024
Thrustmaster

Thrustmaster Ferrari GT Experience Bruksanvisning

13 Oktober 2024
Thrustmaster

Thrustmaster T3PA Add-On Gaming Pedal Set Bruksanvisning

6 Oktober 2024
Hori

Hori Battle Pad Bruksanvisning

4 Oktober 2024
Razer

Razer Wolverine V3 Pro Bruksanvisning

3 Oktober 2024
Hori

Hori Fighting Commander OCTA Bruksanvisning

3 Oktober 2024
Saitek

Saitek PS2700 Bruksanvisning

3 Oktober 2024