EMOS M0320 Bruksanvisning
EMOS
Multimeter
M0320
Läs nedan 📖 manual på svenska för EMOS M0320 (40 sidor) i kategorin Multimeter. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/40
2202014000_31-M0320_00_01 90 × 130 mm
www.emos.eu
M0320 | MD-110
GB Digital Multimeter
CZ Digitální multimetr
SK Digitálny multimeter
PL Multimetr cyfrowy
HU Digitális multiméter
SI Digitalni multimeter
RS|HR|BA|ME Digitalni multimetar
DE Digitales Multimeter
UA Цифровий мультиметр
RO Multimetru digital
LT Skaitmeninis multimetras
LV Digitālais multimetrs
EE Digitaalne multimeeter
BG Цифров мултиметър
3
• Do not measure voltages higher than 300 V or current higher than 200 mA!
• Do not measure current, if the void voltage in an open circuit is higher than 300 V.
• The „COM“ terminal must always be connected to the reference measuring ground.
• If you detect abnormal measurement results, do not use the multimeter. If you are
not sure about the cause of a failure, contact the service center.
• Do not measure higher voltages and currents than those indicated on the front
panel of the multimeter. There is a risk of electric shock and damage of the
multimeter!
• Verify that the multimeter is working properly before use. Test a circuit where you
know its electrical parameters.
• Turn o the power supply of the circuit before you connect the multimeter to the
circuit of which current you intend to measure to.
• Do not use or store the multimeter in environments with high temperature, dust
and moisture. It is also not recommended to use the device in an environment
where a strong magnetic eld is present or where there is a risk of explosion or a re.
• When replacing the battery or other parts of the multimeter, use spare parts of
the same type and specication. Replace the parts only when the multimeter is
switched o and disconnected!
• Do not change or modify the internal circuits of the multimeter!
• Caution when measuring voltages higher than 30 V AC rms, 42 V peak or 60 V
DC. Risk of electric shock!
• When handling the measuring pins make sure to hold them behind the nger
barrier.
• To avoid electric shock, do not touch any bare wires with your hands or skin.
• Disconnect the measuring pins from the circuit before opening the cover of the
multimeter.
• Do not take any measurements if the cover of the multimeter is removed or it
is loose.
• When the display shows a discharged battery icon „ “, replace the battery.
Otherwise, the subsequently performed measurements can be inaccurate. This
can lead to biased results of the measurement resulting in an electric shock!
WARNING
Use a multimeter MD-110 only as specied below, otherwise it may result in damage
of the device or your health. Pay attention to the following instructions:
• Disconnect circuits from their power source and discharge high-voltage capacitors,
before you make any measurement of resistance, diode or current.
• Check if a round range selector switch knob is in the correct position before
measurement. Do not make any changes in the measuring range (by turning
the round range selector switch knob) during the measurement in any case! This
could cause damage of the device.
• When measuring current, turn o the power supply of circuit before you connect
the multimeter.
Description of the device
Digital multimeter MD-110 belongs to a series of compact devices with 3.5 digital
display, designed to measure AC and DC voltage, DC current, resistance and diode
4
testing. It indicates exceeding of the measured range. It has an auto power o feature. The
multimeter oers an overload protection and information about low battery. Ideal use of
the multimeter MD-110 is for example in workshops, laboratories and homes.
Technical specications
Display: LCD, 1999 (3.5 digits) with an automatic polarity indication
Working temperature: 0°C to 40°C <75%
Storage temperature: -10°C to 50°C, relative humidity <85%
Power: 1× 12 V (23 A)
Low battery: indication by battery symbol on the display
Over range indication: display number “1” on the LCD
Measurement category: CAT III (300 V)
Dimensions and weight: 57×95×30 mm, 82 g (including battery)
Front view of the multimeter
1. Display - 3.5 digit LCD display with maximum indication up to 1999
2. Rotary switch knob
It is used for the desired function selection and also for turning the measuring device
on and o. Set the rotary switch knob to the OFF position, when you are not using the
device.
3. Test conductors
Measurement accuracy
Accuracy is specied for a period of one year after calibration, at 18°C to 28°C and at a
relative humidity of 75%.
Accuracy specication has the following form:
± ([% of device reading] + [number of the lowest valid digits])
DC voltage (DC)
Range Resolution Accuracy
200 mV 100 µV ± (0.5 % + 5)
2000 mV 1 mV
± (0.8 % + 5)20 V 10 mV
200 V 100 mV
300 V 1 V ± (1 % + 5)
Input impedance: 1 MΩ
Maximum allowable voltage input: 300 V
Alternating voltage (AC)
Range Resolution Accuracy
200 V 100 mV ± (1.2 % + 10)
300 V 1 V ± (1.2 % + 10)
Input impedance: about 500 kΩ
Frequency range: 40 Hz to 400 Hz
Maximum allowable voltage input: 300 V
Response: Average, calibrated to a virtual value of the sine wave
Produktspecifikationer
| Varumärke: | EMOS |
| Kategori: | Multimeter |
| Modell: | M0320 |
Behöver du hjälp?
Om du behöver hjälp med EMOS M0320 ställ en fråga nedan och andra användare kommer att svara dig
Multimeter EMOS Manualer
25 September 2024
6 September 2024
2 September 2024
29 Augusti 2024
27 Augusti 2024
25 Augusti 2024
17 Augusti 2024
22 Juli 2024
Multimeter Manualer
- Multimeter Abus
- Multimeter Alecto
- Multimeter Appa
- Multimeter Amprobe
- Multimeter Amiko
- Multimeter Silverline
- Multimeter Ferm
- Multimeter Workzone
- Multimeter Yato
- Multimeter Milwaukee
- Multimeter Elro
- Multimeter Extech
- Multimeter Tacklife
- Multimeter Schneider
- Multimeter Metrix
- Multimeter Benning
- Multimeter Voltcraft
- Multimeter Somogyi
- Multimeter Velleman
- Multimeter Profile
- Multimeter Steren
- Multimeter Kyoritsu
- Multimeter Ideal
- Multimeter Flir
- Multimeter Maxwell
- Multimeter Digitus
- Multimeter Testboy
- Multimeter Hager
- Multimeter TFA
- Multimeter Clas Ohlson
- Multimeter Powerfix
- Multimeter Owon
- Multimeter Fluke
- Multimeter Basetech
- Multimeter Projecta
- Multimeter Etekcity
- Multimeter Greenlee
- Multimeter Högert
- Multimeter Laserliner
- Multimeter REV
- Multimeter Testo
- Multimeter Keithley
- Multimeter Monacor
- Multimeter Metrel
- Multimeter Multimetrix
- Multimeter Digi-tool
- Multimeter Brandson
- Multimeter GW Instek
- Multimeter Skandia
- Multimeter Elma
- Multimeter Testec
- Multimeter Beha-Amprobe
- Multimeter Vimar
- Multimeter Uni-T
- Multimeter Kewtech
- Multimeter Strex
- Multimeter Mastech
- Multimeter PeakTech
- Multimeter Sonel
- Multimeter MBS
- Multimeter MGL Avionics
- Multimeter Chauvin Arnoux
- Multimeter Megger
- Multimeter Gossen Metrawatt
- Multimeter Rigol
- Multimeter PCE Instruments
- Multimeter Micronta
- Multimeter CEM
- Multimeter Horex
- Multimeter Cosinus
- Multimeter Joy-it
- Multimeter Klein Tools
- Multimeter Aim TTi
- Multimeter Kurth Electronic
- Multimeter Wiha
- Multimeter IWH
- Multimeter Weltron
- Multimeter Sanwa
- Multimeter Rohde & Schwarz
- Multimeter EEVBlog
- Multimeter Kingcraft
- Multimeter Weidmüller
- Multimeter HT Instruments
- Multimeter Caltek
- Multimeter Elworks
- Multimeter Qian
- Multimeter Bearware
- Multimeter Noyafa
Nyaste Multimeter Manualer
8 Januari 2025
3 Januari 2025
1 Januari 2025
29 December 2024
29 December 2024
29 December 2024
29 December 2024
28 December 2024
23 December 2024
22 December 2024