EXSYS EX-3515 Bruksanvisning

EXSYS Kontroller EX-3515

Läs nedan 📖 manual på svenska för EXSYS EX-3515 (10 sidor) i kategorin Kontroller. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/10
1
Thank you for purchasing this 2-Port SATA3 RAID/HyperDuo PCIe
Card. It is designed to support up to 2 SATA3 ports in RAID 0 and
RAID 1 modes and HyperDuo modes for SSD (Solid State Drive) and
hard drive combination. It supports SATA3 SSD and hard drives with
up to 6.0Gbps data rate. It is an ideal solution to add new SATA3 SSD
and hard drives for your system.
Features:
Supports 1-lane 5.0Gb/s PCI Express Gen.2 Data Transfer Rate
Built-in 2 Internal SATA3 Ports
Supports RAID 0, RAID 1, HyperDuo (Safe or Capacity) Modes
Supports Windows based RAID GUI (Marvell Storage Utility, MSU)
Supports SATA3 transfer rate up to 6.0Gb/s (600Mbytes/sec)
Supports RAID 1 Rebuild by BIOS Setup Utility
Supports Windows 2003, 2008, XP, Vista and Win 7
EX-3515
2-Port SATA3 RAID/HyperDuo PCIe Card
1. Introduction
2. Board Layout
JP1 BIOS
Enable/Disable
Jumper
J2:
SATA3
Channel 1
J1:
SATA3
Channel 0
Extra secure
mounting
holes
2-Port SATA3 RAID/HyperDuo PCIe Card
2
The JP1 can be used to disable the BIOS on the card for some
critical applications, please leave the jumper at “ENA” all the time.
JP1: BIOS Enable/Disable Jumper
1. Power down the computer, remove the computer cover.
2. Choose an unused PCI Express bus slot, unscrew and remove the slot
cover.
3. Place the SATA3 RAID PCIe Card into the slot. Carefully press the
board into the slot until it seats firmly.
4. Secure the SATA3 RAID PCIe Card with the slot cover screw.
5. Install the SATA cables from the SATA connectors to your SATA devices.
6. Carefully reinstall the computer cover. Insert and tighten the
computer cover screws.
7. Power up the PC and observe the monitor. The BIOS lists all Serial ATA
devices attached to the SATA3 RAID/HyperDuo PCIe Card. For
example:
Marvell 88SE91xx Adapter – BIOS Version x.x.x.xxxx
PCIe p2-x1 5.0Gbps
Mode: CPU AHCI
Virtual Disk
No Virtual Disk!
Physical Disk
[ID] [DISK Name] [Size] [Speed]
0 SATA ST32000641AS 1.83TB 6.0G
1 SATA ST32000641AS 1.83TB 6.0G
Press <Ctrl>+<M> to enter BIOS Setup or <Space> to continue
If the information displayed on your monitor is correct (the installed
devices are listed with the correct device name, etc.), congratulations!
You have successfully installed the SATA3 RAID/HyperDuo PCIe Card in
4. Hardware Installation
BIOS Enabled:
Jumper Installed at “ENA”
(Default)
BIOS Disabled:
Jumper Installed at “DIS”
3. Jumper Settings
ENA DIS
ENA DIS
2-Port SATA3 RAID/HyperDuo PCIe Card
3
your computer. If you want to configure your RAID drives, press and
hold the 2 keys, Ctrl M and , to enter the BIOS Setup Utility for this card.
You can configure the SATA RAID or HyperDuo modes in the BIOS
Setup.
5.1 RAID Modes
This chapter will help you to know the RAID and HyperDuo modes
supported by the SATA3 RAID/HyperDuo PCIe Card.
5.2 Non-RAID mode (Single Disk Mode)
This mode is the Single Disk mode. Each disk drive will be treated as
one disk volume in the operating system.
5.3 Striping (RAID 0)
Read and write sectors of data interleaved between multiple drives.
When any disk member fails, it affects the entire array. Performance
is better than a single drive since the workload is balanced
between the array members. This array type is for high performance
systems. Identical drives are recommended (but not necessary, if
the sizes differ, it will truncate the bigger drive so the sizes match, it
will cause a waste) for performance as well as data storage
efficiency. The disk array data capacity is equal to the number of
drive members times the smallest member capacity.
5.4 Mirroring (RAID 1)
Writes duplicate data on to a pair of drives while reads are
performed in parallel. The RAID controller performs reads using
advanced data handling techniques that distribute the workload in
a more efficient manner than using a single drive. When a read
Write data Streams
… ….. 4, 3, 2, 1
1
3
:
:
2
4
:
:
Read data Streams
….. 4, 3, 2, 1
Stripe member 1
Stripe member 2
5. RAID and HyperDuo Modes

Produktspecifikationer

Varumärke: EXSYS
Kategori: Kontroller
Modell: EX-3515

Behöver du hjälp?

Om du behöver hjälp med EXSYS EX-3515 ställ en fråga nedan och andra användare kommer att svara dig


Kontroller EXSYS Manualer

EXSYS

EXSYS EX-3517 Bruksanvisning

18 September 2024
EXSYS

EXSYS EX-3516 Bruksanvisning

18 September 2024
EXSYS

EXSYS EX-3670 Bruksanvisning

18 September 2024
EXSYS

EXSYS EX-3455 Bruksanvisning

18 September 2024
EXSYS

EXSYS EX-3515 Bruksanvisning

18 September 2024

Kontroller Manualer

Nyaste Kontroller Manualer

8BitDo

8BitDo Ultimate C Wired Controller Xbox Bruksanvisning

26 Oktober 2024
DJI

DJI Motion Controller Bruksanvisning

18 Oktober 2024
PCE Instruments

PCE Instruments PCE-RE100P Bruksanvisning

16 Oktober 2024
PCE Instruments

PCE Instruments PCE-RE21R Bruksanvisning

16 Oktober 2024
Thrustmaster

Thrustmaster Ferrari GT Experience Bruksanvisning

13 Oktober 2024
Thrustmaster

Thrustmaster T3PA Add-On Gaming Pedal Set Bruksanvisning

6 Oktober 2024
Hori

Hori Battle Pad Bruksanvisning

4 Oktober 2024
Razer

Razer Wolverine V3 Pro Bruksanvisning

3 Oktober 2024
Hori

Hori Fighting Commander OCTA Bruksanvisning

3 Oktober 2024
Saitek

Saitek PS2700 Bruksanvisning

3 Oktober 2024