Extech DL160 Bruksanvisning

Extech Mätutrustning DL160

Läs nedan 📖 manual på svenska för Extech DL160 (5 sidor) i kategorin Mätutrustning. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/5
USER GUIDE
Dual Input True RMS
AC Voltage/Current Datalogger
Model DL160
Additional User Manual translations available at www.extech.com
3 - - 6 7/DL160 en US_V1. 22
Description and Button Functions
1. LCD Description
Auto power off (does not apply when recording), the meter
will automatically shuts off after 5mins without any button
presses.
REC: Recording status. After the record mode is set up by the
software, press the START/STOP button for more than 4
seconds to begin recording. icon the meter is recording This will be displayed and indicates
data. Press the same button again for more than 4 seconds to stop recording.
. Wh . Record until full is selected en the memory is full, the datalogger will stop recording
Continuous recording is selected. When the memory is full, the data will overwrite the oldest
data.
FULL . Memory full and recording has stopped
Battery status, when completely filled in (black) the battery power is full. When there is only
one section should be replaced with a new one. , filled in the battery is exhausted and
2. AC adaptor Jack
3. ON/OFF Button
4. MAX/MIN: Press the button one time to display the MAX (maximum)
reading. Press again to display the MIN (minimum) reading. A third press
will exit MAX/MIN mode. The meter will automatically exit MAX/MIN mode
in 10 seconds if no button is pressed.
5. CH Input Jacks: Insert the current voltage sensor to these ports or to
measure and record the data.
6. CHANNEL: Select the channel for display on the LCD
7. START/STOP: After the datalogger is setup from the software, press the
START/STOP button for 4 seconds to begin recording. Press the button again for 4 seconds to stop
recording.
Recording cannot be started again until the data is downloaded to the software!
8. USB Port
9. AC Current Clamp Jaw: Clamp the jaws around a single conductor
for AC current measurements to 200A
10. Jaw Opening Trigger
11. CH Plug
12. AC Voltage Probes or Alligator clips
13. Voltage module
14. CH Plug
4 - - 6 7/DL160 en US_V1. 22
Operation
1. Install 4 fresh AAA batteries or connect the AC adaptor.
2. - Set up the datalogger using the software provided.
See the Software Help Guide that comes with the software.
3. . Connect either the voltage or current probes, or one of each the bottom of the meter
4. . Connect the voltage test leads or the current probes to the AC source to be measured
5. t Press and Hold the START/STOP button for four seconds o start recording. The “REC” icon
will appear in the display indication that recording has begun.
6. Press and Hold the START/STOP button for four seconds to stop recording. The “REC” icon
will disappear from . the display
NOTE: if you STOP the recording you MUST reprogram the meter with the software before
recording again.
7. Remove the probes from the test circuit, connect the datalogger to a PC and use the
supplied software to download the data.
Voltage Test Leads
Single Phase: Connect one lead to one phase and the other lead to the Neutral line.
Multi phase: Connect one lead to one phase and the other lead to another phase.
Current clamps
Connect the clamp over one lead only and the clamp jaw must fully close in order to measure
correctly.
Note: If the clock does not set to the correct time, replace the 3V button battery internal to the
meter
PC Software
This meter has the capability to connect to and communicate with a PC.
Check the software download page of the website www.extech.com/software for the latest
version of the PC software and its operating system compatibility.
Download and unzip the software. Run ExtechInstaller.exe and then refer to the instructions
provided in the HELP Utility within the software program.

Produktspecifikationer

Varumärke: Extech
Kategori: Mätutrustning
Modell: DL160

Behöver du hjälp?

Om du behöver hjälp med Extech DL160 ställ en fråga nedan och andra användare kommer att svara dig


Mätutrustning Extech Manualer

Extech

Extech 380941 Bruksanvisning

23 Oktober 2024
Extech

Extech 380926 Bruksanvisning

23 Oktober 2024
Extech

Extech PRC20 Bruksanvisning

25 September 2024
Extech

Extech PRC30 Bruksanvisning

25 September 2024
Extech

Extech SD900 Bruksanvisning

25 September 2024
Extech

Extech PRC15 Bruksanvisning

25 September 2024
Extech

Extech 412300A Bruksanvisning

25 September 2024
Extech

Extech 412400 Bruksanvisning

25 September 2024
Extech

Extech 433201A Bruksanvisning

25 September 2024
Extech

Extech SD910 Bruksanvisning

25 September 2024

Mätutrustning Manualer

Nyaste Mätutrustning Manualer

PCE Instruments

PCE Instruments PCE-PMI 1 Bruksanvisning

14 Januari 2025
PCE Instruments

PCE Instruments PCE-324 Bruksanvisning

14 Januari 2025
PCE Instruments

PCE Instruments PCE-TC 32N Bruksanvisning

14 Januari 2025
PCE Instruments

PCE Instruments PCE-ACO 9500 Bruksanvisning

14 Januari 2025
Klein Tools

Klein Tools CL810 Bruksanvisning

14 Januari 2025
Klein Tools

Klein Tools CL710 Bruksanvisning

14 Januari 2025
Ebro

Ebro PHT 830 Bruksanvisning

13 Januari 2025
Gossen Metrawatt

Gossen Metrawatt PROFiTEST H+E EASY CHECK Bruksanvisning

10 Januari 2025
PCE Instruments

PCE Instruments PCE-VT 3950S Bruksanvisning

9 Januari 2025
PCE Instruments

PCE Instruments PCE-VT 3750S Bruksanvisning

9 Januari 2025