Extech SDL310 Bruksanvisning

Extech Multimeter SDL310

Läs nedan 📖 manual på svenska för Extech SDL310 (11 sidor) i kategorin Multimeter. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/11
USER GUIDE
Vane Thermo-Anemometer /
Datalogger
Model SDL310
2 SDL310-EU-EN V1.4 07/13
Introduction
Congratulations on your purchase of the Extech SDL310 Thermo-Anemometer Datalogger. This meter
displays and stores air velocity and temperature readings. Temperature readings from the
thermometer built into the vane probe or from an externally connected type K or J thermocouple
temperature probe can be displayed and recorded. Data is stored on an SD card for transfer to a PC.
In addition, an RS232 port allows data streaming to a PC. This instrument is shipped fully tested and
calibrated and, with proper use, will provide years of reliable service. Please visit the Extech
Instruments website (www.extech.com) to check for the latest version of this User Guide. Extech
Instruments is an ISO-9001 certified company.
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer to the
manual for further information.
Meter Description
1. Thermocouple input
2. Vane input plug
3. Air velocity reading
4. Units of measure
5. HOLD / Backlight key
6. MAX-MIN key
7. SET and Clock key
8. PC interface jack
9. Reset key
10. Power Adaptor jack
11. SD card slot
12. ENTER and LOG key
13. Down ▼arrow and FUNCTION key
14. Up ▲ arrow and UNITS key
15. Power ON-OFF key
16. Temperature reading with units of measure
17. Anemometer vane
18. Colored dot faces the air flow
19. Vane handle
20. Vane connecting cable
Notes:
Battery compartment, tilt stand, and tripod mount are located on the rear of the instrument.
Items 8, 9, and 10 are located behind the snap-off compartment cover on right side of meter.
3 SDL310-EU-EN V1.4 07/13
Operation
Power ON-OFF
Power the meter by pressing and holding the power key for at least 1.5 seconds.
Press and hold the power key for at least 1.5 seconds to power OFF the meter.
Meter Functions
This meter has two modes of operation. Press and hold the FUNCTION key for at least 1.5 seconds
to switch from one mode to the other.
Air Velocity plus Temperature mode (meter briefly displays An icon)
Type K or J thermocouple temperature mode (meter briefly displays tP icon)
Air Velocity plus Temperature Mode
1. Select the Air Velocity and Temperature mode.
2. Connect the vane probe to the meter’s probe jack (top right of meter) via the probe plug.
3. Hold the probe by its handle and allow the air flow to enter the vane. Note that the air flow must
face the vane’s colored dot.
4. The meter will display the air velocity measurement (upper display area) and the air
temperature (lower display area)
Changing the Air Velocity Unit of Measure
This meter offers five (5) units of measure selections for air velocity: m/s (meters per second), FPM
(feet per minute), Km/h (kilometers per hour), knots, and mph (miles per hour).
1. Press and hold the UNIT key for at least 1.5 seconds to switch from one unit of measure to
another.
2. Note that pressing and holding the UNIT key continuously allows for quicker scrolling. Release
the key when the desired unit of measure is displayed.
Thermcouple (Type J or K) Temperature Mode
1. Select the Thermocouple Temperature mode using the FUNCTION button.
2. The meter will display a ‘J’ or a ‘K’; on the left side of the display indicating the current setting.
To change the thermocouple type, refer to the Setup Mode section.
3. Connect a Type J or Type K thermocouple to the meter’s sub-miniature thermocouple jack (top
of meter on the left).
4. Hold the thermocouple in the air in the area to be tested.
5. The meter will display the thermocouple temperature in the main display area.
6. To change the temperature unit of measure (°C and °F) refer to the Setup Mode section.
Data Hold
To freeze a measurement on the display, press the HOLD key momentarily. The meter will emit a
beep, the reading will hold, and the HOLD display icon will switch on. Press the HOLD key again to
release the display and exit the Data Hold mode returning the meter to the normal operating mode.

Produktspecifikationer

Varumärke: Extech
Kategori: Multimeter
Modell: SDL310

Behöver du hjälp?

Om du behöver hjälp med Extech SDL310 ställ en fråga nedan och andra användare kommer att svara dig


Multimeter Extech Manualer

Extech

Extech 380942 Bruksanvisning

23 December 2024
Extech

Extech DM220 Bruksanvisning

19 September 2024
Extech

Extech MA440 Bruksanvisning

16 September 2024
Extech

Extech EX355 Bruksanvisning

16 September 2024
Extech

Extech EX623 Bruksanvisning

16 September 2024
Extech

Extech MA443 Bruksanvisning

16 September 2024
Extech

Extech MG302 Bruksanvisning

11 September 2024
Extech

Extech Ex 830 Bruksanvisning

6 September 2024
Extech

Extech Ex 810 Bruksanvisning

3 September 2024
Extech

Extech EX 710 Bruksanvisning

2 September 2024

Multimeter Manualer

Nyaste Multimeter Manualer

Metrix

Metrix MTX 3293B Bruksanvisning

8 Januari 2025
Testboy

Testboy Pen 1000 Bruksanvisning

3 Januari 2025
Testec

Testec TT-CC 220 Bruksanvisning

1 Januari 2025
Megger

Megger DPM1000 Bruksanvisning

29 December 2024
Rigol

Rigol RP1300H Bruksanvisning

29 December 2024
Klein Tools

Klein Tools MM300 Bruksanvisning

29 December 2024
Klein Tools

Klein Tools ET910 Bruksanvisning

29 December 2024
Ideal

Ideal 61-342 Bruksanvisning

28 December 2024
Owon

Owon HDS100 Bruksanvisning

22 December 2024
Owon

Owon 1000A Bruksanvisning

19 December 2024